Resumen del contenido incluido en la página 13
Setting up the system Connecting the speakers Front Speakers Right Left Center Speaker FRONT CENTER + - R L C RED WHITE GREEN SPEAKERS (8-16Ω ) + + - - SURROUND SURROUND BACK SUB WOOFER + PRE OUT - R L SB GRAY BLUE PURPLE SPEAKERS (8-16Ω ) Powered sub woofer Right Left Surround Back Surround Speakers (Be sure to connect both surround speakers) EN 13 *5330/08-15/EN 13 1/21/03, 9:53 PM
Resumen del contenido incluido en la página 14
Setting up the system Connecting the terminals Connecting the antennas AM loop antenna 1 Strip coating. 2 Push the lever. The supplied loop antenna is for use indoors. Place it as far as possible from the receiver, TV set, speaker cords and power cord, and adjust the direction for best reception. AM antenna terminal connections 1 Push lever. 2 Insert cord. 3 Release lever. 3 Insert the cord. 4 Return the lever. FM indoor antenna • Never short circuit the + and – speaker cords. • If the left and
Resumen del contenido incluido en la página 15
Setting up the system Connecting the system control Connecting system control cords after connecting a KENWOOD SYSTEM CONTROL OPERATIONS audio component system lets you take advantage of convenient system control operations. Remote Control Lets you operate this unit with the system remote supplied with the This unit is compatible only with the [SL-16] mode. The system receiver. control operation is not available if the unit is connected in the [XS8], [XS], or [XR] connection mode. Automatic Oper
Resumen del contenido incluido en la página 16
Preparing for surround sound Speaker settings 2 Use the MULTI CONTROL knob or Multi %/fi keys to select the To enable you to obtain optimum enjoyment from the receiver’s listening modes, make sure to complete the speaker settings (subwoofer, front, speaker system setting. center, and surround speakers) as described below. 1 2WAY 2SPKR : For selected Kenwood speaker – for example, KS-307HT. POWER ON/STANDBY (KRF-V6070D) 2 2WAY 3SPKR : For selected Kenwood speaker – for example, ON/STANDBY (VR-707)
Resumen del contenido incluido en la página 17
Preparing for surround sound 0 Use the MULTI CONTROL knob or Multi %/fi keys to select 5Adjust the speaker volume level. the appropriate surround speaker setting. From your usual listening position, adjust the volume levels. The volume levels from each speaker should be the same. If you have selected “LRG” as the center speaker setting, 1 SURR NML (normal) : Average size surround speakers are 1 Press the SETUP key to begin TEST TONE. connected to the receiver. The selection of AUTO/MANUAL TEST T
Resumen del contenido incluido en la página 18
Preparing for surround sound Normal playback Preparing for playback 5 Repeat steps 3 and 4 to input the distance for each of the Some preparatory steps are needed before starting playback. speakers. POWER ON/STANDBY 6 Setup is complete when the EXIT indication appears. SPEAKERS (KRF-V6070D) ON/STANDBY ON/OFF (VR-707) • The speakers you have selected should appear on the display. Confirm that all the speakers have been correctly selected. 7 Press the SETUP key to exit the SETUP mode. POWER AUTO
Resumen del contenido incluido en la página 19
Normal playback Listening to a source component Adjusting the sound SPEAKERS ON/OFF VOLUME CONTROL VOLUME CONTROL ACTIVE EQ PHONES MULTI CONTROL MUTE INPUT SELECTOR Input Selector Multi % / fi Mute ¢ + + ¢ + + Tone VOL +/– VOL 4 – – 4 – + + Bass Boost Loudness Active EQ Adjusting the Tone (remote control only) Use the INPUT SELECTOR knob or keys to select the source 1 you want to listen to. You can adjust the sound quality when the receiver is in the PCM stereo and analog stereo mode. The input s
Resumen del contenido incluido en la página 20
Normal playback Recording Recording audio (analog sources) Adjusting the Loudness mode (remote control only) You can adjust the Loudness function which controls the low volume settings to maintain the music’s richness. The adjustment can be made when the receiver is in the PCM stereo and analog stereo mode. Press the Loudness key to turn the Loudness setting ON. To cancel Press the Loudness key again so that the “Loudness” indicator INPUT SELECTOR goes off. Muting the sound Recording a music sou
Resumen del contenido incluido en la página 1
AUDIO VIDEO SURROUND RECEIVER
VR-707
KRF-V6070D
INSTRUCTION MANUAL
KENWOOD CORPORATION
This instruction manual is for some models. Model availability and features
(functions) may differ depending on the country and sales area.
About the supplied remote control
Compared to standard remote controls, the remote control supplied with this receiver has several
operation modes. These modes enable the remote control to control other audio/video components. In
order to effectively use the remote contro
Resumen del contenido incluido en la página 2
Caution : Read this page carefully to ensure safe Before applying the power operation. Units are designed for operation as follows. How to use this manual U.S.A. and Canada ........................................... AC 120 V only This manual is divided into four sections, Preparations, Operations, Remote Control, and Additional Information. Australia ........................................................... AC 240 V only Europe and U.K. ............................................... AC 230 V
Resumen del contenido incluido en la página 3
Before applying the power Contents Unpacking Unpack the unit carefully and make sure that all accessories are Caution : Read the pages marked carefully to ensure present. safe operation. FM indoor antenna (1) AM loop antenna (1) Before applying the power .............................. 2 Safety precautions ............................................. 2 How to use this manual ..................................... 2 Unpacking .......................................................... 3 Preparing
Resumen del contenido incluido en la página 4
Before applying the power Preparing the remote control Channel space switching (Except for the U.S.A., Canada and Australia) Loading the batteries The space between radio channels has been set to the one that prevails in the area to which the system is shipped. However, if the 1 Remove the cover. 2 Insert the batteries. current channel space setting does not match the setting in the area where the system is to be used, for instance when you move from area 1 or area 2 shown in the following table
Resumen del contenido incluido en la página 5
Before applying the power Special features For the U.S.A. FCC WARNING True home theater sound This equipment may generate or use radio frequency energy. Changes This receiver incorporates a wide variety of surround modes to bring you or modifications to this equipment may cause harmful interference maximum enjoyment from your video software. Select a surround mode unless the modifications are expressly approved in the instruction according to your equipment or the software you are going to play
Resumen del contenido incluido en la página 6
Names and functions of parts Main Unit Frequency display, AUTO DETECT Input display, indicator Preset channel display, Surround mode display DTS indicator 6CH INPUT indicator Speaker indicator MUTE indicator Band indicators DIGITAL indicator AUTO indicator CLIP indicator AB MEMO. indicator ST. indicator TONE indicator TUNED indicator DOLBY DIGITAL DSP indicator Speaker selection indicators indicator LOUDNESS indicator Input channel indicators STEREO indicator Output channel indicators PRO LOGI
Resumen del contenido incluido en la página 7
P. Call r r e e w w o o P Names and functions of parts Remote control unit This remote control unit can be use not only for Kenwood products but also for non-Kenwood products by setting the appropriate manufacturer’s setup codes. º ^ DVD TUNER 6CH CD VID1 1 DVD MD VID2 TAPE & AUX TV POWER RCVR * 2 ( 4 5 3 6 Multi Enter 2 7 3 Multi 1 8 ) 0 9 + 10 + 100 ¡ TV Mute 4 Page Return OSD ™ Last / A/B Exit Guide Disc Skip Menu 5 £ Disc Sel. Mute Input Sel. 6 ¢ ¢ + + Tone 7 VOL CH ∞ Sound 4 – – 8 § Bass TV
Resumen del contenido incluido en la página 8
Setting up the system Make connections as shown in the following pages. Input mode settings When connecting the related system components, be sure to refer to the instruction manuals supplied with CD/DVD, VIDEO2 and DVD/6CH inputs each include jacks for digital audio input and analog audio input. the components you are connecting. After completing connections and turning on the receiver, follow the Do not connect the power cord to a wall outlet until all steps below. connections are completed. L
Resumen del contenido incluido en la página 9
Setting up the system Shape of AC outlets Connecting audio components U.S.A. and Canada Australia Other countries SYSTEM CONTROL jacks % + + To AC wall outlet - - AUDIO L R REC OUT PLAY IN REC OUT PLAY IN AUX CD/DVD MD / TAPE VIDEO1 IN OUT Video component ) IN OUT Cassette deck or MD recorder OUT CD or DVD player Other component OUT EN 9 *5330/08-15/EN 9 1/21/03, 9:53 PM
Resumen del contenido incluido en la página 10
Setting up the system Connecting video components About the S-VIDEO jacks S-VIDEO jacks S-VIDEO S-VIDEO VIDEO 2 DVD MONITOR IN IN OUT Use the S-VIDEO jacks to make connections to video components with S-VIDEO IN/OUT jacks. If you use the S-VIDEO • jacks to connect your video + + playback components, be sure to use the S-VIDEO - - jacks when connecting your monitor and video recording components. VIDEO AUDIO DVD MONITOR IN OUT VIDEO 2 IN REC OUT PLAY IN PLAY IN VIDEO1 VIDEO 2 VIDEO 1 VIDEO 1 IN
Resumen del contenido incluido en la página 11
Setting up the system Digital connections The digital in jacks can accept DTS, Dolby Digital, or PCM signals. Connect components capable of outputting DTS, Dolby Digital, or standard PCM (CD) format digital signals. If you have connected any digital components to the receiver, be sure to read the “Input mode settings” section carefully. 8 + + - - COAXIAL OPTICAL VIDEO 2 CD / DVD DVD / 6CH DIGITAL IN OPTICAL DIGITAL OUT (AUDIO) Optical fiber cable CD or DVD player COAXIAL DIGITAL OUT (AUDIO) Comp
Resumen del contenido incluido en la página 12
Setting up the system Connecting a DVD player (6-channel input) If you have connected a DVD player to the receiver with digital connection, be sure to read the “Input mode settings” section carefully. 8 DVD IN + + - - DVD / 6CH INPUT VIDEO COAXIAL OPTICAL CENTER VIDEO 2 CD / DVD DVD IN MONITOR OUT VIDEO 2 IN SUB DVD / 6CH FRONT SURROUND WOOFER DIGITAL IN VIDEO 1 VIDEO 1 IN OUT VIDEO OUT FRONT SURROUND SUBWOOFER (Yellow RCA OUT L/R OUT L/R OUT pin cord) DVD player CENTER OUT S-VIDEO COAXIAL OUT
