Manual de instrucciones de Krell Industries KSP7B

Resumen del contenido incluido en la página 1

KSP-7B STEREO PREAMPLIFIER OWNER’S MANUAL

Resumen del contenido incluido en la página 2

45 Connair Road Orange, CT 06477-0533, USA INTRODUCTION & GENERAL INFORMATION Thank you for purchasing the KRELL KSP-7B Preamplifier. The KSP-7B is the latest evolution of KRELL’s entry level preamplifier technology. Many of its design concepts are similar to our more expensive preamplifiers and are wholly unique to KRELL. Two important design features are dual- mono operation (all active stages are powered by independent tracking regulators) and the complete absence of any capacitors in the sig

Resumen del contenido incluido en la página 3

ABOUT THE OWNERS~ MANUAL The KSP-7B Owner’s Manual is divided into various groups of information. The purpose of he document as a whole is to familiarize you with the unit and guide you through its set-up, installation and operation in a logical progression. The Table of Contents is as follows: A. Unpacking B. Phono Section Set-Up C. Installation: 1. Cautions 2. Unit Location Guidelines and Installation 3. Connection of Inputs and Outputs 4. Turn-on of the Preamplifier D. Operation E. Warranty a

Resumen del contenido incluido en la página 4

Moving Coil Cartridges:’ The KSP-7B is shipped with the phono section gain set for moving coil cartridges and a load of 800 ohms. The load can be changed with a set of internal switches. To access these the top cover must be removed with the supplied allen driver. At the left-rear of the unit there is a two-position toggle switch. In the factory-supplied position the switch lever is towards the rear panel of the unit. If you are using a moving coil cartridge do not change the switch position. To

Resumen del contenido incluido en la página 5

When installing th’e KSP-7B, always connect the DC cable between the Co preamplifier chassis and the power supply before plugging the power supply into the AC mains. Always disconnect the AC from the mains before disconnecting the d. DC cable from the preamplifier. e. The KSP-7B Select switch should be in the Mute position and the volume control fully counterclockwise while making connections. Our custom RCA connectors are made to very exacting standards. Connectors of lesser quality may damage

Resumen del contenido incluido en la página 6

This supply does not’ require that an AC circuit be dedicated for its use only. It should be connected to a 15 or 20 amp circuit that is dedicated for the source components and preamplifier. Do not connect this supply to the mains with light-gauge (18 or higher) extension cords or multiple outlet adapters. AC extension cords, outlet strips and good quality surge protectors that are rated for 15 amps and are grounded are acceptable. b. Preamplifier Location Guidelines The KSP-7B chassis measures

Resumen del contenido incluido en la página 7

i. For use with an~plifiers with single-ended (unbalanced) inputs: connect the RCA Main Outputs to the amplifier inputs. This constitutes the conventional hook-up for a single-ended unbalanced system. ii. For use with amplifiers with balanced inputs: connect the XLR Main Outputs to the amplifier inputs. The pin assignments are as follows: 1 = ground, 2 = non-inverted output, 3 = inverted output. Make the connections between the Main Outputs and amplifier(s) and/or crossovers at this time. 4. Tur

Resumen del contenido incluido en la página 8

Note: Components that are not being listened to should be turned off or have their volume turned down. For instance, a tuner should be turned off or have its volume lowered while it is not being listened to. Use the ~ switch to choose between the output of the ~ switch or the playblack from a tape deck for monitoring. This can be done when a recording is being made, such as with a three-head tape deck, or during playback only. Use the Gain toggle switch to adjust the overall gain of the line sec

Resumen del contenido incluido en la página 9

The KSP-7B has a limited warranty of five years from the date of purchase. Please return the completed warranty card immediately after successful installation and operation are completed. The warranty for KRELL products is valid in the country to which they were originally shipped and at the factory. If you think there are problems with your unit, please contact your dealer or the factory immediately. Should your unit need to be repaired, contact the factory or your dealer (distributor) for a re