Resumen del contenido incluido en la página 1
Leader in Audio Engineering
KRC-HR
PREAMPLIFIER
OWNER’S REFERENCE
Resumen del contenido incluido en la página 2
TABLE OF CONTENTS 2 INTRODUCTION UNPACKING 3 4 THEATER-THROUGHPUT SETUP 5 BASIC INSTALLATION 6 INPUT/OUTPUT CONNECTIONS REAR PANEL DESCRIPTION 7 8 BASIC PREAMPLIFIER OPERATION 9 FRONT PANEL DESCRIPTION 10 REMOTE CONTROL 11 PROTECTION CIRCUITRY INDICATORS 12 QUESTIONS AND ANSWERS 14 SPECIFICATIONS 15 WARRANTY AND SERVICE
Resumen del contenido incluido en la página 3
INTRODUCTION Thank you for your purchase of the KRELL KRC-HR remote control preamplifier. The KRC-HR combines refinements of the original KRC with a radical approach to volume control circuitry. The HR designation signifies HIGHEST RESOLUTION due to the substantial improvement in sonic quality provided by our most sophisticated electronic volume control. The unit also has a Theater-Throughput, which allows easy installation of the unit within a home theater system. Please see page 4 for details
Resumen del contenido incluido en la página 4
UNPACKING i. Open the box and remove the top layer of foam. 2. Remove the KRC-HR and the foam tray surrounding it. The following items will now be visible: 1 KRC-HR power supply 1 KRC-HR remote control 1 8 ft. DC power cable 1 T- 10 torx (for remote) 1 T-15 torx 1 AC power cord If any of these items are not included, please contact your authorized dealer immediately for assistance. 3. Remove from the plastic bags, the preamplifier, power supply, remote control and power supply cable connectors.
Resumen del contenido incluido en la página 5
THEATER-THROUGHPUT SETUP NOTE: If the KRC-HR must be handled after the top cover has been removed, the unit must be held only on the sides of the chassis. Never move the KRC-HR while the top cover is off by holding the front panel. When reinstalling the top cover, insert the four screws into the chassis sides first and lightly tighten them. Install the screws in the top surface and tighten them lightly. Then tighten all screws firmly, starting with the side screws and finishing with the top scre
Resumen del contenido incluido en la página 6
BASIC INSTALLATION 1. Place the unit on a firm level surface free from excessive dirt or moisture. The KRC-HR is not particularly hum sensitive, allowing other components to be placed on or around it. If the optional phono card is installed in the KRC-HR, some components such as Digital to Analog converters, power supplies or components with motors can induce hum into the phono stage. 2. Place the power supply in a location away from hum sensitive components such as turntables or phonostages. Co
Resumen del contenido incluido en la página 7
INPUT AND OUTPUT CONNECTIONS CAUTIONS: When making connections to this component or any other, make sure that the power amplifier is OFF. Make sure all cable terminations are of the highest quality, free from frayed ends, shorts or cold solder joints. 1. Connect the left and right inputs of your source equipment to the inputs on the KRC-HR. The KRC-HR is equipped with 4 single-ended inputs, 2 balanced capable inputs and 1 single-ended tape input. 2. If the optional phono card is included in your
Resumen del contenido incluido en la página 8
REAR PANEL DESCRIPTION INPUTS Four single-ended inputs via standard RCA connectors PH (Line level input if phono board is not installed) S-2 S-3 S-4 Two balanced inputs via standard XLR connectors B-1 B-2 Tape input via standard RCA connectors MAIN OUTPUTS Single ended RCA output connectors Balanced XLR output connectors Balanced XLR output pin configuration: Pin 1 Shield (ground) Pin 2 Non-inverting (hot) Pin 3 Inverting TAPE OUTPUT Record output via RCA connectors 7
Resumen del contenido incluido en la página 9
BASIC PREAMPLIFIER OPERATION The KRC-HR has the flexibility of a remote controlled device but does not require special attention in order to perform simple functions. The KRC-HR will function much like. other KRELL preamplifiers. The unit can be operated from the front panel controls or via the remote control. All functions available on the front panel can also be accomplished from the KRC-HR remote control. This provides the ability to sit in your favorite listening position while controlling a
Resumen del contenido incluido en la página 10
FRONT PANEL DESCRIPTION INPUT SELECTION PH Selects phono input (line level input when phono board not installed) S-2 Selects S-2 input S-3 Selects S-3 input S-4 Selects S-4 input B-1 Selects B- 1 input B-2 Selects B-2 input FUNCTIONS TAPE Selects tape input and allows monitoring of tape return PHASE Inverts absolute polarity of the main output 180 degrees LED illuminates when polarity is reversed GAIN Low 6dB, High 12dB. LED illuminates in High position MUTE No signal output when LED is on L BAL
Resumen del contenido incluido en la página 11
REMOTE CONTROL 1. When a function button on the remote control is pressed and held, the blue pilot LED will flash on the KRC-HR. When the button is released, the flashing stops. This indicates that the KRC-HR has received a command. 2. The functions of the remote control are identical to the front panel functions. BATTERY INSTALLATION Batteries should be replaced when the KRC-HR functions from the remote control become intermittent. 1. Remove the four hex head screws from the back of the control
Resumen del contenido incluido en la página 12
PROTECTION CIRCUITRY The KRC-HR is the first high-end preamplifier to have protection circuitry at the input and output. The indicators on the KRC-HR, which are described below, will give you a general location of a problem in your audio system. 1. When the KRC-HR’s monitoring circuitry recognizes excessive DC levels at one of the inputs, the output disconnects from the front-end circuits and the LED corresponding to that input will flash repeatedly until the problem is removed. If you try to se
Resumen del contenido incluido en la página 13
QUESTIONS AND ANSWERS When I turn up the volume on the KRC-HR, a loud hum is present from the Q. loudspeakers. What could this be? Ao Hum can be caused by several different disturbances. Check to make sure that all of the cables, (in and out of the KRC-HR) are sound and making proper contact. Make sure that there are no power supplies or hum inducing components on top of or directly below the KRC-HR. You could also be experiencing a ground loop in the system. Put a 3-prong to 2-prong AC adaptor,
Resumen del contenido incluido en la página 14
Q. Why do I have to turn up the volume so high to get music at a normal listening level? Ao If your system does not seem to have enough gain, you are probably not using the balanced input and output capabilities of the KRC-HR. Each balanced termination has 6dB more gain than a single-ended termination. More important, however, is that the balanced lines provide superior sonic quality. If you must use single-ended terminations, use the High gain setting, which has 6dB more gain than the Low posit
Resumen del contenido incluido en la página 15
SPECIFICATIONS GAIN: 6dB or 12dB SIGNAL TO NOISE: 96dB unweighted THD: 1KHz less than .01% 20KHz less than .01% INPUT IMPEDANCE: 47,000 Ohms (47K Ohm) OUTPUT IMPEDANCE: 5 Ohms OUTPUT VOLTAGE: 14 volts R.M.S. DIMENSIONS: Unit: 19.0" Wide 14.5" Deep 2.75" High, with feet Power Supply: 1 1" Wide 9" Deep 2.5" High All operational features, functions, and specifications and policies are subject to change without notification. 14
Resumen del contenido incluido en la página 16
WARRANTY AND SERVICE THERE ARE NO USER-SERVICEABLE PARTS INSIDE ANY KRELL PRODUCT. The KRELL KRC-HR has a limited and transferable warranty of five years for parts and labor. The warranty period begins on the date of retail purchase, as noted on the retail sales slip provided by an authorized KRELL Dealer or Distributor, or on the warranty registration card sent to KRELL. In the event adequate proof of purchase date is unavailable, the warranty period will begin on the date the unit was original
Resumen del contenido incluido en la página 17
WARRANTY AND SERVICE KRELL is not responsible for any damage to units incurred in transit. If any shipping damages are incurred during transit of your units to the factory, you must initiate filing of the insurance claim. Likewise, KRELL will file claims for shipping damages incurred during transit of your units from the factory to you. The use of any packing material other than original is not recommended. KRELL may, at its discretion, pack a unit in new material for the return shipment. Krell
Resumen del contenido incluido en la página 18
KRELL 45 Connair Road ¯ Orange, CT 06477-3650 USA 203-799-9954 ¯ Fax: 203-799-9796 ©1997 by Krell® Industries, Inc. All rights reserved. P/N 1960602000023
