Resumen del contenido incluido en la página 1
Resumen del contenido incluido en la página 2
Introduction KS-Series System Components Owner’s Manual Models: KS65.2 / KS6.2 / KS5.2 Attention: Congratulations! You have purchased one of the most Please record your purchase information in the area advanced speaker component systems in car below. We recommend attaching the original sales audio. The KS-Series Component System was receipt to this manual for future reference. designed by the award-winning KICKER speaker design team, tested in the judging If you require service on this speaker d
Resumen del contenido incluido en la página 3
Features CIMP ™ (Curvilinear Injection-Molded Polypropylene High-Power Tinsel Lead Wires eliminate broken leads and Woofer Cones) is a high performance composite, which power loss, due to the common use of “insufficient-gauge” lead remains rigid, minimizes cone flex and lowers harmonic wires. distortion. The CIMP ™ consists of a one-piece, injection-molded polypropylene material that moves as a Aluminum Dome Tweeter with Neodymium Magnet piston, exhibiting power and control. provides a
Resumen del contenido incluido en la página 4
Specifications Performance Model: KS5.2 KS6.2 KS65.2 Speaker Design 2 - Way 2 - Way 2 - Way Rated Impedance, ohm 4 4 4 DC Resistance, ohm 3 3 3 Sensitivity [SPLo], dB @ 1W, 1m 88 88 88 Power Range, Watts RMS 6-65 6-75 6-75 Peak Power Handling, Watts 130 150 150 Effective Frequency Range, Hz 38-21k 35-21k 33-21k Top-Mount Depth, in (cm) 2 (5.1) 1 15/16 (4.9) 2 1/8 (5.4) Bottom-Mount Depth, in (cm) 2 1/4 (5.7) 2 1/4 (5.7) 2 1/4 (5.7)
Resumen del contenido incluido en la página 5
Installation Your Kicker KS-Series System Component drivers are specifically designed for mounting in free-air applications. The speakers do not require a sealed enclosure for optimum performance. It is important to isolate the sound coming off the front of the driver from the sound radiating from the back of the driver. This isolation is usually accomplished by using the correct size driver in a factory speaker location. Mounting Use caution when mounting speakers through the rear deck or packa
Resumen del contenido incluido en la página 6
Installation Installation If custom door mounting locations for the KS-Series System Components are desired, be careful to avoid interference from the window and door lock mechanisms. The first step is to find a location on the door panel that will accept the dimensions of the speaker. Then remove the door panel from the door, and check for operational clearance of the window. Cycle the window all the way down and up. If metal must be cut to mount the speakers, avoid structural metal and brace
Resumen del contenido incluido en la página 7
Installation Tweeter Mounting The tweeter can be mounted one of four ways: flush, surface, angled and coaxial mounting. For flush mounting applications, please refer to the illustration in Figure 3. Mount the tweeter as high up on the door and as far forward as possible without interference from the dashboard. Choose a flat location on the door with space behind the panel to allow room for the mounting nut. After checking the clearances, cut a 2” (5.1 cm) hole in the door panel. Place the mounti
Resumen del contenido incluido en la página 8
Installation Installation Tweeter Mounting continued The tweeter can be mounted in the center of the midrange. This creates a high quality coaxial speaker. Remove the tweeter face plate by screwing it off and install the supplied smaller face plate. Then install the tweeter back plate by securing the supplied phillips-head machine screw to the plate, as outlined in Step 1, in Figure 4. Unscrew the bullet shaped phase plug from the center of the midrange, Step 2. Feed the wires through the inclu
Resumen del contenido incluido en la página 9
Wiring Options There are three sets of wires supplied with the Kicker KS-Series System Components. One set has two different size female connectors .205” (5.2 mm) and .110” (2.8 mm) and is designed to plug on to the terminal of the midrange. The other end of this wire goes to the midrange output on the supplied crossover. The other two sets of wires do not have any connectors on either end. One set goes from the tweeter output of the crossover to the short wire coming out of the tweeter; join t
Resumen del contenido incluido en la página 10
Installation Butt Connectors Butt Connectors Wiring Options Wiring two KS-Series System Components to a single channel Modern high performance system components have a lower DC Resistance than what used to be available. The Kicker KS-Series System Components are rated at four ohms and work with any source unit or amplifier designed to operate at a four ohm load. If you want to use two KS-Series System Components on each channel of your source unit or amplifier wire the system compone
Resumen del contenido incluido en la página 11
WHAT IS NOT COVERED? Acoustics LIMITED WARRANTY This warranty is valid only if the product is used for the purpose for which it was Kicker warrants this product to be free from defects in material and workmanship designed. under normal use for a period of THREE (3) MONTHS from date of original It does not cover: purchase with receipt. When purchased from an Authorized KICKER Dealer it is warranted for ONE (1) YEAR from date of original purchase with receipt. In all cases • Damage due to impr
Resumen del contenido incluido en la página 12
