Resumen del contenido incluido en la página 1
User Manual
iNUKE
NU6000DSP/NU3000DSP/NU1000DSP
Ultra-Lightweight, High-Density 6000/3000/1000-Watt Power
Amplifier with DSP Control and USB Interface
Resumen del contenido incluido en la página 2
2 iNUKE NU6000DSP/NU3000DSP/NU1000DSP User Manual Table of Contents Thank you ....................................................................... 2 Important Safety Instructions ...................................... 3 Legal Disclaimer ............................................................. 3 Limited Warranty ........................................................... 3 1. Introduction ............................................................... 5 1.1 Before you get started ......
Resumen del contenido incluido en la página 3
3 iNUKE NU6000DSP/NU3000DSP/NU1000DSP User Manual 9. Do not defeat the safety purpose of the polarized UNDERTAKING OR REPRESENTATION. THIS MANUAL Imp Imp or ot ran tant Safe t Safett y y or grounding-type plug. A polarized plug has two blades IS COPYRIGHTED. NO PART OF THIS MANUAL MAY Instructions Instructions with one wider than the other. A grounding-type plug BE REPRODUCED OR TRANSMITTED IN ANY FORM has two blades and a third grounding prong. The wide OR BY ANY MEANS, ELECTRONIC OR MECHAN
Resumen del contenido incluido en la página 4
4 iNUKE NU6000DSP/NU3000DSP/NU1000DSP User Manual (1) (3) (4) (7) (2) (5) (6) (8) (9) Front panel control elements 1. Introduction Should your BEHRINGER product malfunction, it is our intention to have it repaired as quickly as possible. To arrange for warranty service, please contact 1.1 Before you get started the BEHRINGER retailer from whom the equipment was purchased. Should your BEHRINGER dealer not be located in your vicinity, you may directly contact 1.1.1 Shipment one of our subsi
Resumen del contenido incluido en la página 5
5 iNUKE NU6000DSP/NU3000DSP/NU1000DSP User Manual (10) (11) (12) (13) (14) Rear panel control elements (NU6000DSP shown) 3.2.2 SETUP screens 2.2 Rear panel The SETUP screens access the preset, panel lock, device naming, and LCD screen (10) BREAKER (automated fuse, NU6000DSP only). After eliminating the cause of contrast functions. To access these functions, press the SETUP button, and then faulty operation, simply depress the BREAKER and power up the unit again. move up and down through th
Resumen del contenido incluido en la página 6
6 iNUKE NU6000DSP/NU3000DSP/NU1000DSP User Manual 2. Press the SELECT encoder knob to access the DSP’s internal Preset list on the SETUP 2/4: Panel Lock next sub-screen. The correct sub-screen will display the EDIT TITLE and SAVE The Panel Lock function uses a 4-character alphanumeric access code to lock PRESET options on the right-hand side of the screen. the front panel controls and prevent unauthorized changes to DSP settings. Current settings can still be viewed while the unit is locked,
Resumen del contenido incluido en la página 7
7 iNUKE NU6000DSP/NU3000DSP/NU1000DSP User Manual 2. Press the SELECT encoder knob to access the editing screen. BIAMP1 3. Choose the backwards arrow by turning the SELECT knob and press it to BIAMP1 mode splits the Channel A input signal at a programmable frequency delete the existing characters of the current preset name. point, and then routes the resulting high and low frequency signals through a parallel chain of DSP modules with independent equalization, signal delay, 4. Rotate the SELE
Resumen del contenido incluido en la página 8
8 iNUKE NU6000DSP/NU3000DSP/NU1000DSP User Manual 2. Press the SELECT encoder knob to enter the parameter screens for your 5. Set the filter thresholds for high-pass (HPfreq) and low-pass (LPfreq) by chosen EQ band. rotating the SELECT encoder knob. 3. Press the UP / DOWN arrow keys to switch between parameters. The chosen 6. Set the filter’s overall signal gain (Gain) by rotating the SELECT encoder knob. parameter will appear highlighted. 4. Rotate the SELECT encoder knob to change parameter v
Resumen del contenido incluido en la página 9
9 iNUKE NU6000DSP/NU3000DSP/NU1000DSP User Manual 10. Adjust attack (Atime) and release (Rtime) to your preferred values. 3.3 BEHRINGER Amp Remote Software 11. Press the SELECT encoder when finished to return to the top-level DEQ screen. DELAY The DELAY DSP module digitally slows the final signal output from the amplifier by a programmable amount (expressed as either distance or time). This signal delay helps prevent phase and synchronization problems caused by sound traveling through air ov
Resumen del contenido incluido en la página 10
10 iNUKE NU6000DSP/NU3000DSP/NU1000DSP User Manual Output Meters 3.3.4 Configuration The output meters show the signal level at the end of the DSP signal chain, following the Limit module. If the signal activates the limiter, the red Limit indicator will light over the channel experiencing an overload. 3.3.2 Function Tabs The Configuration tab displays two main sets of software controls: The BEHRINGER Amp Remote window allows the user to access DSP functions via embedded tabs accessible nea
Resumen del contenido incluido en la página 11
11 iNUKE NU6000DSP/NU3000DSP/NU1000DSP User Manual Stereo mode routes the signal from both the A and B inputs through a single Delay series of DSP modules. Each DSP module processes both the A and B signals The Delay function digitally slows the final signal output from the amplifier by a with identical, linked settings. The linked Delay and Limit parameters can be programmable amount (expressed as either distance or time). This signal delay helps controlled from Stereo mode’s consolidated C
Resumen del contenido incluido en la página 12
12 iNUKE NU6000DSP/NU3000DSP/NU1000DSP User Manual 3. Choose a Hold value either by rotating the Hold virtual knob or by entering a Filter/Crossover Control View value (in milliseconds) into the matching text box below the knob. 4. Choose a Release value either by rotating the Release virtual knob or by entering a value (in milliseconds) into the matching text box below the knob. 3.3.5 Filter/Crossover The Control View of the Filter/Crossover tab contains virtual knob controls for Gain, High
Resumen del contenido incluido en la página 13
13 iNUKE NU6000DSP/NU3000DSP/NU1000DSP User Manual • Frequency Curve—displays the filter curves in visual form, and allows 3. The EQ curve shown by the solid yellow fill will re-size and adjust as you click-and-drag manipulation of EQ frequencies and gain. move the cursor up and down the frequency line. The virtual gain knob and gain dB displayed in the Control View will also simultaneously change as you The Frequency Curve and Control View interact with each other and move the cursor up an
Resumen del contenido incluido en la página 14
14 iNUKE NU6000DSP/NU3000DSP/NU1000DSP User Manual Adjusting dynamic EQ gain via click-and-drag 6. Program your desired ratio by selecting from the Ratio pulldown menu. Similar to a compressor, higher ratio values yield a more intense 1. Click and hold on the numbered box at the top of the desired dynamic equalization effect. EQ band frequency line. 7. Adjust the attack (Attack) and release (Release) values by rotating each 2. Move the cursor vertically up or down the frequency line to the d
Resumen del contenido incluido en la página 15
15 iNUKE NU6000DSP/NU3000DSP/NU1000DSP User Manual 2. Click on the Recall button in the upper left of the Amp Presets section. The Renaming an amplifier selected preset’s name will appear in the text box next to the Recall button. 1. Type the new amplifier name directly into the text box to the left of the All settings contained in the preset will automatically deploy. Rename Amp virtual button near the bottom of the Amp Connection section. Saving a preset to the amp’s internal memory 2. Click
Resumen del contenido incluido en la página 16
16 iNUKE NU6000DSP/NU3000DSP/NU1000DSP User Manual Programming BEHRINGER Amp Remote Software for Again, matching parameters will automatically appear in both filter’s Control bi-amping View settings. 1. Select the Configuration tab. 9. Set the crossover frequency by using any of these three methods: 2. Choose the Bi-Amp 2 signal path in the Configuration tab. A confirmation a) Rotate the Low Pass 2 or High Pass 3 virtual Freq knobs in the Control View. window will pop up. The crossover frequen
Resumen del contenido incluido en la página 17
17 iNUKE NU6000DSP/NU3000DSP/NU1000DSP User Manual 5. Installation Unbalanced ¼" TS connector strain relief clamp 5.1 Rack mounting sleeve Your iNUKE amplifier fits into a 19" rack and requires two rack units. Install tip into the rack using four attaching screws and washers for the front panel. Reinforce the back panel, especially if you will be taking the iNUKE on the road. Make sure enough cool air reaches the rack, especially when other rack equipment emanates a lot of heat. The iNUKE
Resumen del contenido incluido en la página 18
18 iNUKE NU6000DSP/NU3000DSP/NU1000DSP User Manual 6. Specifications NU6000DSP Connectors Output Power Inputs 2 x combo jacks Maximum Output Power Input impedance 10 kΩ unbalanced, 20 kΩ balanced Stereo Outputs 2 x locking-style professional 8 Ω per channel, stereo 1600 W speaker connectors 4 Ω per channel, stereo 3100 W Output circuit type Class D 2 Ω per channel, stereo — Distortion <0.2% Bridged mono Frequency response 20 Hz to 20 kHz, +0 / -2 dB 8 Ω — Damping factor >140 @ 8 Ω 4 Ω — Sign
Resumen del contenido incluido en la página 19
19 iNUKE NU6000DSP/NU3000DSP/NU1000DSP User Manual NU3000DSP Connectors Output Power Inputs 2 x combo jacks Maximum Output Power Input impedance 10 kΩ unbalanced, 20 kΩ balanced Stereo Outputs 2 x locking-style professional 8 Ω per channel, stereo 440 W speaker connectors 4 Ω per channel, stereo 820 W Output circuit type Class D 2 Ω per channel, stereo 1520 W Distortion <0.3% Bridged mono Frequency response 20 Hz to 20 kHz, +0 / -1 dB 8 Ω 1520 W Damping factor >145 @ 8 Ω 4 Ω 3000 W Signal-to-
Resumen del contenido incluido en la página 20
20 iNUKE NU6000DSP/NU3000DSP/NU1000DSP User Manual NU1000DSP Connectors Output Power Inputs 2 x combo jacks Maximum Output Power Input impedance 10 kΩ unbalanced, 20 kΩ balanced Stereo Outputs 2 x locking-style professional 8 Ω per channel, stereo 160 W speaker connectors 4 Ω per channel, stereo 310 W Output circuit type Class D 2 Ω per channel, stereo 530 W Distortion <0.1% Bridged mono Frequency response 20 Hz to 20 kHz, +0 / -1 dB 8 Ω 620 W Damping factor >155 @ 8 Ω 4 Ω 1050 W Signal-to-no
