Resumen del contenido incluido en la página 1
(In-Wall)
SC-IW
Subwoofer
TM
SubContractor Series
INSTALLATION
MANUAL
Resumen del contenido incluido en la página 2
Caution! . www.v elodyne.com SC-IW Installation Manual i
Resumen del contenido incluido en la página 3
Attention! . www.v elodyne.com SC-IW Installation Manual ii
Resumen del contenido incluido en la página 4
Vorsicht! . www.v elodyne.com SC-IW Installation Manual iii
Resumen del contenido incluido en la página 5
Attenzione! . www.v elodyne.com SC-IW Installation Manual iv
Resumen del contenido incluido en la página 6
Table of Contents Product Overview.................................................................................................1 - Driver Technology ...........................................................................................1 - Cabinet Technology .........................................................................................1 Installation Overview.............................................................................................3 New Construction Installat
Resumen del contenido incluido en la página 7
Product Overview The SC-IW (In-Wall) subwoofer can be installed in a variety of locations and positions in any given installation. Although this product is extremely versatile and flexible in its uses, it has been specifically designed for two major applications - New Construction Installations and Retro-Fit Installations in structures made of traditional 2x4 studs with 16 inch spacing, on-center. This document provides the detailed process for properly installing the SC-IW into a wall. The S
Resumen del contenido incluido en la página 8
The SC-IW consists of two cabinets — the “driver module” and the “back box.” (a.k.a. the “Enclosure”). Unlike other in-wall products where a back box may be optional, the SC-IW requires both enclosures, unaltered, for every installation. In new construction situations, the back box is in installed first (for example, at the framing or rough out stage), and the driver module is installed later in the trim out stage. In retrofit situations both boxes are typically installed together. The driver mo
Resumen del contenido incluido en la página 9
The SC-IW comes in two completely separate cartons — the SC-IWBB (Back Box) and the SC-IWDVR (Driver). Parts included with the SC-IWBB rough install kit: • In-wall back box - Qty 1 • Mudring for "retro fit" installation - Qty 1 • Installation manual - Qty 1 • Installation hardware Parts included with the SC-IWDVR driver module: • SC-IW driver module - Qty 1 • Clamp ring - Qty 2 • Standard grille - Qty 1 • Designer grille - Qty 1 • Hardware • Installation manual - Qty 1 Installation Overview You
Resumen del contenido incluido en la página 10
New Construction Installation — Standard Grille Note: This installation process assumes that the installer has access to the open framed 2x4 studded wall with 16 inch spacing. In the event that the stud spacing is larger, an additional 2x4 or other spacer can be used to fill the space between the SC-IW back box and the neighboring stud. Step 1 - Install Mudring Unpack the first carton (SC-IWBB) and place the contents on the floor. Remove the mudring from the packaging. At this time the decisi
Resumen del contenido incluido en la página 11
Step 2 - Install Back Box Once the mudring is stapled into place, the back box should be installed using eight of the phillips drive flat head screws included in the package. When installing the back box, the mudring should be aligned to the white line on the cabinet. Once the mudring and the back box are aligned, install the back box as shown. Figure 2: Install Back Box . www.v elodyne.com SC-IW Installation Manual 5
Resumen del contenido incluido en la página 12
Step 3 - Route Wire Route the wire from the location where the electronics gear is located to where the SC-IW will be. There is "extra space" between the studs and the back box in the event that the wire has to pass along the side of the back box to the driver module. Figure 3: Route Wire Step 4 - Cover Rubber Couplings If the installation is not going to be finished right away, Velodyne recommends "taping" or otherwise “covering” the two connecting tubes to prevent paint, drywall and/or foreig
Resumen del contenido incluido en la página 13
Step 5 - Finish Wall The wall can now be finished in a traditional fashion utilizing the appropriate drywall thickness, standard texturing and finishing methods. Be sure to advise the "finishing” contractors that they are to drywall up to the edge of the mudring, as the mudring is the place holder for the installation of the driver module and standard grille. Figure 4: Finish Wall Note: Steps 6 through 14 presume that you have obtained and are ready to install the SC-IWDVR (In-Wall Driver Modul
Resumen del contenido incluido en la página 14
Step 7 - Remove Mudring At this point, the mudring can be removed. It should be easily removed by "pulling it through" the drywall opening. After it is removed, discard. Figure 5: Remove Mudring . www.v elodyne.com SC-IW Installation Manual 8
Resumen del contenido incluido en la página 15
Step 8 - Place Clamp Rings on Driver Module Remove the two clamp rings from the packaging and place a clamp ring onto each of the bottom edges of the tubes. Note: The position of the clamp ring is critical. Make sure that the screw section of the ring is on either side of the tube and not on the front or the back. Please see picture below. Screw must face outward Figure 6: Clamp Ring Placement . www.v elodyne.com SC-IW Installation Manual 9
Resumen del contenido incluido en la página 16
Step 9 - Install Driver Module Insert the driver module assembly through the opening left in the wall by the mudring and slide the plastic tubes onto the two connection tubes The connection tubes should slide all the way down onto the surface of the driver module assembly. Once the tubes are flush with the driver module, firmly tighten the two clamp rings to seal the rubber coupling to the plastic tube. Note: The silicon rubber tubes should slide over the tubes protruding from the driver modu
Resumen del contenido incluido en la página 17
Step 10 - Remove Metal Grille Obtain the standard grille with integrated scoop and remove the metal grille insert, as shown, in the picture below. Figure 8: Metal Grille Insert Removal Note: The grille can be painted to match the de´cor. The supplied paint mask can be used to paint the grille frame while the metal grille insert can be painted separately. . www.v elodyne.com SC-IW Installation Manual 11
Resumen del contenido incluido en la página 18
Step 11 - Install Grille Frame Install the plastic grille onto the driver module using the four included machine screws. The grille hardware should easily be installed into the side of the cabinet. Tighten using the supplied allen wrench. Figure 9: Grille Frame Installation . www.v elodyne.com SC-IW Installation Manual 12
Resumen del contenido incluido en la página 19
Step 12 - Secure Grille Install two pan head phillips screws (provided) into standard grille into bottom left and bottom right holes. Figure 10: Secure Grille . www.v elodyne.com SC-IW Installation Manual 13
Resumen del contenido incluido en la página 20
Step 13 - Install Metal Grille Insert Figure 11: Metal Grille Insert Installation Step 14 - Installation Complete The installation is complete. Test the installation with bass audio material and check for buzzes, rattles, and air leaks and address accordingly. Figure 12: Completed Installation . www.v elodyne.com SC-IW Installation Manual 14
