Resumen del contenido incluido en la página 1
User Guide
Speakers
SF 26X
®
SpeedMount Ceiling Mount Speakers
68-2222-01 Rev. A
12 13
Resumen del contenido incluido en la página 2
Safety Instructions Safety Instructions • English Инструкция по технике безопасности • Русский WARNING: This symbol, , when used on the product, is intended to ПРЕДУПРЕЖДЕНИЕ: Данный символ, , если указан alert the user of the presence of uninsulated dangerous voltage within на продукте, предупреждает пользователя о наличии the product’s enclosure that may present a risk of electric shock. неизолированного опасного напряжения внутри корпуса продукта, которое может привести к поражению ATTEN
Resumen del contenido incluido en la página 3
Conventions used in this guide notifications The following notifications are used in this guide: CauTIOn: A caution indicates a situation that may result in minor injury. arn w Ing: A warning indicates a situation that has the potential to result in death or severe injury. aTTEnTIOn: Attention indicates a situation that may damage or destroy the product or associated equipment. nOTE: A note draws attention to important information. Specifications availability Product specifications are avail
Resumen del contenido incluido en la página 4
Contents Introduction ....................................................1 About the SF 26X Speaker ................................ 1 Features ............................................................. 1 Application Example ........................................... 2 Installation ......................................................3 Installing the SF 26X in a Suspended Ceiling ...... 3 Painting the Baffle and Grille ............................. 12 SF 26X User Guide • Contents iv
Resumen del contenido incluido en la página 5
Introduction This user guide contains information about the Extron SF 26X Ceiling Mount Speaker. About the SF 26X Speaker The SF 26X speaker is a two-way, low impedance, ceiling-mount speaker system that features an 8 ohm open back speaker with a 6.5 inch woofer and a 3/4 inch tweeter designed for use in non-plenum airspace environments. Features • Open back, infinite baffle design • 8 ohm nominal impedance • 3/4" (1.9 cm) pivoting ferrofluid-cooled dome tweeter • 6.5" (16.5 cm) polyprop
Resumen del contenido incluido en la página 6
Application Example The illustration below is one example of configuring a system using the SF 26X speakers. Extron TLP 1000TV 10" Tabletop TouchLink Touchpanel Extron DTP HDMI 230 Tx Ethernet TCP/IP Transmitter Network INPUTS SIG LINK OVER DTP POWER 12V AUDIO RS-232 IR 0.7A MAX Tx Rx G Tx Rx DTP OUT Audio Ethernet CATx Cable Laptop HDMI up to 230' (70 m) Extron COM1 COM 2 IR RELAY Tx Rx RTS CTS Tx Rx 1 2 1 2 IPL 250 STANDBY/ON POWER SGSG PQLS HDMIOPEN/CLOSE FL OFF LAN 12V
Resumen del contenido incluido en la página 7
Installation The Installation section describes: • Installing the SF 26X in a Suspended Ceiling • Painting the Baffle and Grille Installing the SF 26X in a Suspended Ceiling 1. Remove power from all devices. NOTE: If the baffle or grille is to be painted, see the Painting the Baffle and Grille section on page 12. The maximum ceiling tile thickness that the speaker can go into is 1.22 inches (31 mm). 2. Cut a hole for the SF 26X. Use the provided cutout template to outline the hole to be cut
Resumen del contenido incluido en la página 8
6. Attach speaker wires from the ceiling tile hole to the included four-pole captive screw connector using one of the following three methods below. NOTES: • Be sure that the combined impedance of the speaker system does not equal a value less than the rated minimum load impedance of the amplifier. • The maximum number of wires per terminal are as follows: Wire Gauge Table Maximum Number of Wires per Connection Point Wire Gauge 1 12 AWG 2 16 AWG • D
Resumen del contenido incluido en la página 9
• Wiring Multiple Speakers Using Loop-through: A loop-through electrical connection is made on the crossover board of the SF 26X. Connect the wires to the captive screw connectors of the speakers, as shown below. Be sure to tighten the screws. NOTES: • Be sure that the combined impedance of the speaker system does not equal a value less than the rated minimum load impedance of the amplifier. • When a chain of speakers is wired in this configuration, disconnecting one speaker removes
Resumen del contenido incluido en la página 10
• To test the impedance of the entire speaker system, first disconnect the speaker wires from the amplifier and then measure the impedance from the disconnected wires, as shown below. Red Wire (+) disconnected from Amplifier Test Points Amplifier To next speaker Black Wire (-) disconnected from Amplifier Captive Screw Connector Impedance Test Points ATTENTION: Disconnect the speaker system from the amplifier before performing this test, otherwise you may damage the test meter. • The imped
Resumen del contenido incluido en la página 11
• Wiring Speakers in Parallel: Connect the wires to the captive screw connectors of the speakers, as shown below. Be sure to tighten the screws. NOTES: • Be sure that the combined impedance of the speaker system does not equal a value less than the rated minimum load impedance of the amplifier. • When a chain of speakers is wired in this configuration, disconnecting one speaker does not remove power from the remaining speaker in the chain. (Red) (Red) (Black) (Black) Power Ampli e
Resumen del contenido incluido en la página 12
To test the impedance of the entire speaker system, first disconnect the speaker wires from the amplifier and then measure the impedance from the disconnected wires, as shown below. Red Wire (+) disconnected from Amplifier Test Points Amplifier To next speaker Black Wire (-) disconnected from Amplifier Captive Screw Connector Impedance Test Points ATTENTION: Disconnect the speaker system from the amplifier before performing this test, otherwise you may damage the test meter. • Wiring a S
Resumen del contenido incluido en la página 13
7. Insert the captive screw connector into the four-pole receptacle on the speaker crossover board as shown below. Strain Relief Tie off Point Zip Tie Captive Screw Connector Figure 3. Strain Relief Tie Off Point 8. Secure the speaker wire to the strain relief tie off point using the included zip tie as shown above. 9. Mount the SF 26X. a. Insert the SF 26X through the bottom of the hole in the ceiling tile that was cut in step 2. b. Tighten the four screws (clockwise) of the locking arm
Resumen del contenido incluido en la página 14
10. Attach the secondary support line if required, as shown below. Secondary Secondary Tie off Point Support Line Figure 5. Attaching the Secondary Support Line a. Remove the ceiling tile adjacent to the tile where the speaker is mounted. b. Attach the secondary support line. ATTENTION: Do not allow any slack in the secondary support line. c. Replace the adjacent ceiling tile. 11. Pivot the tweeter to aim the mid and high frequencies to the desired spot, as shown below. Figure 6. Pivot
Resumen del contenido incluido en la página 15
12. Position the outer perimeter of the grille into the groove of the speaker baffle. Six magnets pull the grille securely into place, as shown below. Speaker Grille Figure 7. Installing the SF 26X Grille NOTE: Grille hooks ar e pr ovided for r emoval of the grille after installation. SF 26X User Guide • Installation 11
Resumen del contenido incluido en la página 16
Painting the Baffle and Grille NOTE: The cutout template that was used in step 2 of the previous section will be used as a paint shield when painting the outer circumference of the baffle. Painting the Baffle 1. Remove the grille using the provided grille hooks and set the grille aside. 2. Place cutout template over the center of the tweeter so that the woofer and tweeter of the speaker are protected from the paint. 3. Tape over the center hole of the template to prevent any paint from enterin
Resumen del contenido incluido en la página 17
Extron Warranty Extron Electronics warrants this product against defects in materials and workmanship for a period of five years from the date of purchase. In the event of malfunction during the warranty period attributable directly to faulty workmanship and/or materials, Extron Electronics will, at its option, repair or replace said products or components, to whatever extent it shall deem necessary to restore said product to proper operating condition, provided that it is returned within th
