Resumen del contenido incluido en la página 1
Bullet
Network Camera
IP8355EH / IP8365EH
User’s Manual
1.3 / 2MP • 30M IR • Smart Focus System • IP67 •
Cable Management
Rev. 1.0
Rev. 1.0
Resumen del contenido incluido en la página 2
VIVOTEK Table of Contents Overview .....................................................................................................................................................4 Revision History ...................................................................................................................................... 4 Read Before Use .....................................................
Resumen del contenido incluido en la página 3
VIVOTEK URL Commands for the Network Camera ................................................................................................129 Technical Specifications ...........................................................................................................................213 Technology License Notice .......................................................................................................................215 Electromagnetic Compatibility (EMC) .................
Resumen del contenido incluido en la página 4
VIVOTEK Overview VIVOTEK IP8355EH is a professional outdoor dome network camera offering 30 fps @ 1.3-Megapixel resolutions with superb image quality. The IP8365EH provides 30 fps @ 2-Megapixel resolution with superb image quality. Featuring the new improved Wide Dynamic Range Technology WDR Pro II (WDR Pro for IP8365EH), it provides extreme visibility in extremely dark & light environments with 4-shutter capture method. Combined with 3D Noise Reduction Technology, which enables the IP8355E
Resumen del contenido incluido en la página 5
VIVOTEK Read Before Use The use of surveillance devices may be prohibited by law in your country. The Network Camera is not only a high-performance web-ready camera but can also be part of a flexible surveillance system. It is the user’s responsibility to ensure that the operation of such devices is legal before installing this unit for its intended use. It is important to first verify that all contents received are complete according to the Package Contents listed below. Take note of the
Resumen del contenido incluido en la página 6
VIVOTEK 2. Physical Description Lens IR LEDs Light Sensor Zoom out Zoom in Auto Focus Reset Button NTSC-PAL switch NTSC PAL SD/SDHC/SDXC Card Slot Red LED Green LED General I/O Terminal Block 6 - User's Manual
Resumen del contenido incluido en la página 7
VIVOTEK 3. Hardware Installation 1. Attach the alignment sticker to the wall. Drill four holes into the wall. Then hammer the supplied plastic anchors into the holes and secure the plate with supplied screws. 2. Fix the intersection bracket to the side of the Network Camera with two screws. 3. Feed the RJ45 cable through the front opening of the wall mount bracket. (If you want to use external devices such as sensors and alarms, please refer to the assembling steps on the next page.) 4. Pu
Resumen del contenido incluido en la página 8
VIVOTEK 4. Cabling Assembly Waterproof Connector Components of the Waterproof IMPORTANT: Connector Screw Nut (A) If you should need to open the front cover, make sure you tighten it up later so that the Seal (B) camera can be waterproof. Seals (C) Housing (D) Sealing Nut (E) Pin Definitions Pin Definitions 1 AC 24V IN 2 AC 24V IN 3 DC12V+ IN 4 DC12V- IN 5 DI- 6 DI+ 7 DO- 8 DO+ 9 N/C 10 N/C 11 EXT_MIC 15 1 Pin number 12 Audio Out 13 Audio GND 14 TV Out 15 GND 8 - User's Manual
Resumen del contenido incluido en la página 9
VIVOTEK Assembling Steps 1. Disassemble the components of the waterproof connector into part (A) ~ (E) as shown above. 2. Open the rear cover of the Network Camera. 3. Remove the rubber stopper from the bottom of the Network Camera and secure the screw nut (A) tightly. 4. You may choose to use AC24V or DC12V inputs as power source, please feed the power lines through the wall mount bracket and the waterproof connector (E --> D --> B --> A) as illustrated below. Pass power lines through the
Resumen del contenido incluido en la página 10
VIVOTEK RJ45 Cable Connector RJ45 Cable Dimension (unit: mm) Components of the Waterproof Connector Sealing Nut (A) Seal (B) Screw Nut (C) Housing (D) Gasket (E) Assembling Steps 2 3 1 Insert the housing into Insert the seal into the Prepare an Ethernet the screw nut. housing. cable and strip part of the sheath. (C) (D) (B) Recommended cable gauge: O.D. 5.5~7 4 Insert the stripped Ether- 5 6 Clamp the cable Push the RJ45 plug into net cable through the seal- with an RJ45 plug. the housing
Resumen del contenido incluido en la página 11
PARTITION PARTITION LINK RECEIVE POWER COLLISION 1 2 3 4 5 LINK RECEIVE POWER COLLISION 1 2 3 4 5 VIVOTEK 5. Network Deployment Power over Ethernet (PoE) When using a PoE-enabled switch The Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable. Follow the below illustration to connect the Network Camera to a PoE-enabled switch via Ethernet cable. PoE Switch When using a non-PoE switch Use a PoE power injector (optional) to connect between the Ne
Resumen del contenido incluido en la página 12
VIVOTEK Status LED The LED indicates the status of the Network Camera. Item LED status Description Green and Red lit for once, and then turn steady red Power on and system booting 1 Red LED off Power off 2 Steady Red and Green blinking every 1 sec. Network normal (heartbeat) Steady Red and Green LED is off Network failed Red blinking every 0.15 sec., and Green LED blinking 3 Upgrading firmware every 1 sec. Red blinking every 0.15 sec. and Green LED blinking 4 Restoring default every 0.15 se
Resumen del contenido incluido en la página 13
VIVOTEK DI/DO Diagram Please refer to the following illustration for the connection method. GND GND VDC Camera Power VDC Camera Power +12 VDC Switch Switch +12 Input Input VDC Max. Output Output BJT transistor BJT transistor Relay Relay User's Manual - 13
Resumen del contenido incluido en la página 14
VIVOTEK Hardware Reset Reset Button The reset button is used to reset the system or restore the factory default settings. Sometimes resetting the system can return the camera to normal operation. If the system problems remain after reset, restore the factory settings and install again. Reset: Press and release the recessed reset button with a straightened paper clip. Wait for the Network Camera to reboot. Restore: Press and hold the recessed reset button until the status LED rapidly blinks.
Resumen del contenido incluido en la página 15
PARTITION LINK RECEIVE POWER COLLISION 1 2 3 4 5 VIVOTEK Internet connection via a router Before setting up the Network Camera over the Internet, make sure you have a router and follow the steps below. 1. Connect your Network Camera behind a router, the Internet environment is illustrated below. Regarding how to obtain your IP address, please refer to Software Installation on page 17 for details. IP address : 192.168.0.3 Subnet mask : 255.255.255.0 WAN (Wide Area Network ) Default router :
Resumen del contenido incluido en la página 16
VIVOTEK Configure the router, virtual server or firewall, so that the router can forward any data com- ing into a preconfigured port number to a network camera on the private network, and allow data from the camera to be transmitted to the outside of the network over the same path. From Forward to 122.146.57.120:8000 192.168.2.10:80 122.146.57.120:8001 192.168.2.11:80 ... ... When properly configured, you can access a camera behind the router using the HTTP request as follows: http://122.1
Resumen del contenido incluido en la página 17
VIVOTEK Software Installation Installation Wizard 2 (IW2), free-bundled software included on the product CD, helps you set up your Network Camera on the LAN. IW2 1. Install IW2 under the Software Utility directory from the software CD. Installation Double-click the IW2 shortcut on your desktop to launch the program. Wizard 2 2. The program will conduct an analysis of your network environment. After your network environment is analyzed, please click Next to continue the program. 3. T
Resumen del contenido incluido en la página 18
VIVOTEK Ready to Use 1. A browser session with the Network Camera should prompt as shown below. 2. You should be able to see live video from your camera. You may also install the 32-channel recording software from the software CD in a deployment consisting of multiple cameras. For its installation details, please refer to its related documents. 18 - User's Manual
Resumen del contenido incluido en la página 19
VIVOTEK NOTE: If you want to use the supplied sun shield for outdoor environments, please follow the steps below to install: 1. Tighten the supplied two hex couplers. 2. Attach the supplied sun shield to the Network Camera and slide it to the desired position. 3. Fix the sun shield with the supplied two screws. 2 1 3 Accessories VIVOTEK also provides other accessories for versatile applications as the following illustrations. Please visit VIVOTEK's official website for more purchase informat
Resumen del contenido incluido en la página 20
VIVOTEK Accessing the Network Camera This chapter explains how to access the Network Camera through web browsers, RTSP players, 3GPP-compatible mobile devices, and VIVOTEK recording software. Using Web Browsers Use Installation Wizard 2 (IW2) to access the Network Cameras on LAN. If your network environment is not a LAN, follow these steps to access the Netwotk Camera: ® 1. Launch your web browser (ex. Microsoft Internet Explorer, Mozilla Firefox, or Google Chrome). 2. Enter the IP address
