Resumen del contenido incluido en la página 1
Bullet
IP8372 Network Camera
User’s Manual
Outdoor • Day & Night • Weather-proof • IP67 •
Cable Management
Rev. 1.1
Rev. 1.1
Resumen del contenido incluido en la página 2
VIVOTEK Table of Contents Overview .....................................................................................................................................................4 Revision History ...................................................................................................................................... 4 Read Before Use .....................................................
Resumen del contenido incluido en la página 3
VIVOTEK Electromagnetic Compatibility (EMC) .......................................................................................................200 User's Manual - 3
Resumen del contenido incluido en la página 4
VIVOTEK Overview VIVOTEK IP8372 is a professional bullet camera offering 5-Megapixel or 1080p Full HD resolution with superb image quality up to 30 fps. Featuring 5-Megapixel resolution and high- performance H.264/MPEG-4/MJPEG compression technology, the IP8372 offers extra-smooth video and wide coverage. The IP8372 employs many advanced features to allow users to fully utilize the high definition video. The ePTZ function enables users to zoom in and focus on a region of interest (ROI) in t
Resumen del contenido incluido en la página 5
VIVOTEK Read Before Use The use of surveillance devices may be prohibited by law in your country. The Network Camera is not only a high-performance web-ready camera but can also be part of a flexible surveillance system. It is the user’s responsibility to ensure that the operation of such devices is legal before installing this unit for its intended use. It is important to first verify that all contents received are complete according to the Package Contents listed below. Take note of the
Resumen del contenido incluido en la página 6
VIVOTEK Physical Description Lens IR LED Light Sensor Status LED Auto Focus Button SD/SDHC/SDXC Card Reset Button Slot NTSC-PAL switch General I/O Terminal Block NTSC PAL Status LED The LED indicates the status of the Network Camera. Item LED status Description Steady Red Power on and system booting 1 Red LED off Power off 2 Blink Red every 0.15 sec. Upgrading Firmware 3 Blink Red every 0.15 sec. Restoring default 6 - User's Manual
Resumen del contenido incluido en la página 7
VIVOTEK DI/DO Diagram Please refer to the following illustration for the connection method. 12V +12V PIN 1 Power+12V PIN 3 or 5 Digital input PIN 2 Digital output PIN 4 or 6 Ground Gnd 4 Gnd 4 VDC 1 1 Camera Power VDC Camera Power +12 5 or 6 Switch VDC 5 or 6 Switch +30 Input Input VDC Max. 2 2 Output Output BJT transistor BJT transistor Relay Relay User's Manual - 7
Resumen del contenido incluido en la página 8
VIVOTEK Hardware Reset Reset Button The reset button is used to reset the system or restore the factory default settings. Sometimes resetting the system can return the camera to normal operation. If the system problems remain after reset, restore the factory settings and install again. Reset: Press and release the recessed reset button. Wait for the Network Camera to reboot. Restore: Press and hold the recessed reset button until the status LED rapidly blinks. Note that all settings will be
Resumen del contenido incluido en la página 9
VIVOTEK Installation Hardware Installation 1. Attach the alignment sticker to the wall. Drill four holes into the wall. Then hammer the supplied plastic anchors into the holes and secure the plate with supplied screws. 2. Fix the intersection bracket to the side of the Network Camera with two screws. 3. Feed the RJ45 cable through the front opening of the wall mount bracket. (If you want to use external devices such as sensors and alarms, please refer to the assembling steps on the next pag
Resumen del contenido incluido en la página 10
VIVOTEK Waterproof Connector Components of the Waterproof Connector Screw Nut (A) Seal (B) Seals (C) Housing (D) Sealing Nut (E) Pin Definitions Open the rear cover by rotating to the alignment mark, and pull the cover off the canister. J3 1 DO+ (12V) 2 Digital Output 3 Digital Input 1 4 Ground 5 Digital Input 2 6 Ground 7 TV Out + 1 8 8 1 8 TV Out - 1 J6 J3 J6 1 Ext. MIC 2 Audio Ground 3 Audio Line out 4 Audio Ground 5 Ground 6 DC 12V+ 7 AC24V- 8 AC24V+ NOTE: In addition to PoE (Power ov
Resumen del contenido incluido en la página 11
VIVOTEK Assembling Steps 1. Disassemble the components of the waterproof connector into part (A) ~ (E) as shown above. 2. Open the rear cover of the Network Camera. 3. Remove the rubber stopper from the bottom of the Network Camera and secure the screw nut (A) tightly. 4. If you need extra power for external devices, please feed the power cable through the wall mount bracket and the waterproof connector (E --> D --> B --> A) as the illustration shown below. Then connect the power cord to t
Resumen del contenido incluido en la página 12
VIVOTEK Cabling Assembly: RJ45 Cable Connector RJ45 Cable Dimension (unit: mm) Components of the Waterproof Connector Sealing Nut (A) Seal (B) Screw Nut (C) Housing (D) Gasket (E) Assembling Steps Insert the housing into Insert the seal into the Prepare an Ethernet 2 3 1 the screw nut. housing. cable and strip part of the sheath. (C) (D) (B) Recommended cable gauge: 24AWG (0.51 mm) Insert the stripped Ether- Clamp the cable Push the RJ45 plug into 4 5 6 net cable through the seal- with an R
Resumen del contenido incluido en la página 13
PARTTON I I LINK RECEIVE POWER COLLISION 1 2 3 4 5 VIVOTEK Network Deployment Setting up the Network Camera over the Internet This section explains how to configure the Network Camera to an Internet connection. 1. If you have external devices such as sensors and alarms, connect them to the general I/O terminal block. 2. Connect the camera to a switch via Ethernet cable. 3. Connect either the DC 12V or AC 24V power wires from the Network Camera to a power outlet. 3 2 Ethernet Switch There ar
Resumen del contenido incluido en la página 14
PARTITION RE LC INEKIVE POWER COLLISION 1 2 3 4 5 VIVOTEK Internet connection via a router Before setting up the Network Camera over the Internet, make sure you have a router and follow the steps below. 1. Connect your Network Camera behind a router, the Internet environment is illustrated below. Regarding how to obtain your IP address, please refer to Software Installation on page 16 for details. IP address : 192.168.0.3 WAN (Wide Area Network ) Subnet mask : 255.255.255.0 Router IP addres
Resumen del contenido incluido en la página 15
PARTITION PARTITION LINK RECEIVE POWER COLLISION 1 2 3 4 5 LINK RECEIVE POWER COLLISION 1 2 3 4 5 VIVOTEK Set up the Network Camera through Power over Ethernet (PoE) When using a PoE-enabled switch The Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable. Follow the below illustration to connect the Network Camera to a PoE-enabled switch via Ethernet cable. power + data transmission PoE Switch When using a non-PoE switch If your switch/router d
Resumen del contenido incluido en la página 16
VIVOTEK Software Installation Installation Wizard 2 (IW2), free-bundled software included on the product CD, helps you set up your Network Camera on the LAN. IW2 1. Install IW2 under the Software Utility directory from the software CD. Installation Double click the IW2 shortcut on your desktop to launch the program. Wizard 2 2. The program will conduct an analysis of your network environment. After your network environment is analyzed, please click Next to continue the program. 3. T
Resumen del contenido incluido en la página 17
VIVOTEK Ready to Use 1. Access the Network Camera on the LAN. 2. Retrieve live video through a web browser or the included ST-7501 recording software. 2012/08/11 10:19:19 User's Manual - 17
Resumen del contenido incluido en la página 18
VIVOTEK NOTE: If you want to use the supplied sun shield for outdoor environments, please follow the steps below to install: 1. Tighten the supplied two hex couplers. 2. Attach the supplied sun shield to the Network Camera and slide it to the desired position. 3. Fix the sun shield with the supplied two screws. 2 1 3 Accessories VIVOTEK also provides other accessories for versatile applications as the following illustrations. Please visit VIVOTEK's official website for more purchase informat
Resumen del contenido incluido en la página 19
VIVOTEK Accessing the Network Camera This chapter explains how to access the Network Camera through web browsers, RTSP players, 3GPP-compatible mobile devices, and VIVOTEK recording software. Using Web Browsers Use Installation Wizard 2 (IW2) to access to the Network Cameras on the LAN. If your network environment is not a LAN, follow these steps to access the Netwotk Camera: ® 1. Launch your web browser (e.g., Microsoft Internet Explorer or Mozilla Firefox). 2. Enter the IP address of the
Resumen del contenido incluido en la página 20
VIVOTEK it is highly recommended to set a password for the Network Camera. For more information about how to enable password protection, please refer to Security on page 79. ® ► If you see a dialog box indicating that your security settings prohibit running ActiveX ® Controls, please enable the ActiveX Controls for your browser. 1. Choose Tools > Internet Options > Security > Custom Level. ® 2. Look for Download signed ActiveX controls; select Enable or Prompt. Click OK. ® 3. Refresh your
