Resumen del contenido incluido en la página 1
Resumen del contenido incluido en la página 2
VIVOTEK Table of Contents Overview 3 Read Before Use ������������������������������������������������������������������������������������������������������������������������������������� 3 Package Contents ����������������������������������������������������
Resumen del contenido incluido en la página 3
VIVOTEK Overview Read Before Use The use of surveillance devices may be prohibited by law in your country� The Network Camera is not only a high-performance web-ready camera but can also be part of a flexible surveillance system. It is the user’s responsibility to ensure that the operation of such devices is legal before installing this unit for its intended use� It is important to first verify that all contents received are complete according to the Package Contents listed below� Take not
Resumen del contenido incluido en la página 4
VIVOTEK Physical Description Front Panel IR LED Lens Light Sensor Back Panel Status LED Reset Button Connectors General I/O Terminal Block Ethernet 10/100 RJ45 Plug Power Cord Socket (Black) 4 - User's Manual
Resumen del contenido incluido en la página 5
VIVOTEK General I/O Terminal Block This Network Camera provides a general I/O terminal block which is used to connect external input / output devices. The pin definitions are described below. AC24V: 24V+ AC24V AC24V: 24V- AC24V DI DI : Digital Input GND GND : Ground Hardware Reset Status LED Reset Button The reset button is used to reset the system or restore the factory default settings� Sometimes resetting the system can return the camera to normal operation� If the system problems rem
Resumen del contenido incluido en la página 6
VIVOTEK Installation Hardware Installation 1. Loose the waterproof connector, then remove the rubber. 2. Loose the back cover. 3� Tear down the aluminum foil vacuum bag and take out the moisture absorber � Attach the supplied moisture absorber to the inner side of the Network Camera (Please replace the � moisture absorber with a new one if you open the back cover after installation) � 4� Make sure all cable lines are securely connected� 5 � Tighten the back cover, rubber and waterproof connec
Resumen del contenido incluido en la página 7
VIVOTEK NOTE ► If you want to use your own cable lines, please loose two supplied screws and take out the power board� Then be careful to make connections as the illustration shown below � Power Cord Upper Side Terminal Block (from left to right) 1: AC24V (red) 2: AC24V (red) 3: DI (white) 4: GND (black) Ethernet Cable Screws Bottom Side User's Manual - 7
Resumen del contenido incluido en la página 8
PARTITION LINK RECEIVE POWER COLLISION 1 2 3 4 5 VIVOTEK Network Deployment Setting up the Network Camera over the Internet This section explains how to configure the Network Camera to an Internet connection� 1. If you have external devices such as sensors and alarms, make connections from the general I/O terminal block� 2. Use the supplied RJ45 female/female coupler to connect the Network Camera to a switch. Use a Category 5 Cross Cable when Network Camera is directly connected to PC� 3 Co
Resumen del contenido incluido en la página 9
PARTITION RELC INEKIVE POWER COLLISION 1 2 3 4 5 VIVOTEK IP address : 192.168.0.3 WAN (Wide Area Network ) Subnet mask : 255.255.255.0 Router IP address : from ISP Default router : 192.168.0.1 Internet LAN (Local Area Network) Router IP address : 192.168.0.1 Cable or DSL Modem IP address : 192.168.0.2 Subnet mask : 255.255.255.0 Default router : 192.168.0.1 2� In this case, if the Local Area Network (LAN) IP address of your Network Camera is 192168 � 0 � 3, please forward the following po
Resumen del contenido incluido en la página 10
PARTITION PARTITION LINK RECEIVE POWER COLLISION 1 2 3 4 5 LINK RECEIVE POWER COLLISION 1 2 3 4 5 VIVOTEK Set up the Network Camera through Power over Ethernet (PoE) When using a PoE-enabled switch The Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable� Follow the below illustration to connect the Network Camera to a PoE-enabled switch via Ethernet cable� power + data transmission PoE Switch When using a non-PoE switch If your switch/router d
Resumen del contenido incluido en la página 11
VIVOTEK Software Installation Installation Wizard 2 (IW2), free-bundled software included on the product CD, helps you set up your Network Camera on the LAN� 1� Install IW2 under the Software Utility directory from the software CD � Double click the IW2 shortcut on your desktop to launch the program� 2� The program will conduct an analysis of your network environment � After your network environment is analyzed, please click Next to continue the program� 3 � The program will search fo
Resumen del contenido incluido en la página 12
VIVOTEK Ready to Use 1� Access the Network Camera on the LAN� 2� Retrieve live video through a web browser or recording software� 12 - User's Manual
Resumen del contenido incluido en la página 13
VIVOTEK Accessing the Network Camera This chapter explains how to access the Network Camera through web browsers, RTSP players, 3GPP-compatible mobile devices, and VIVOTEK recording software� Using Web Browsers Use Installation Wizard 2 (IW2) to access to the Network Cameras on the LAN � If your network environment is not a LAN, follow these steps to access the Network Camera: ® 1. Launch your web browser (ex. Microsoft Internet Explorer, Mozilla Firefox, or Netscape). 2. Enter the IP addres
Resumen del contenido incluido en la página 14
VIVOTEK ► By default, the Network Camera is not password-protected. To prevent unauthorized access, it is highly recommended to set a password for the Network Camera� For more information about how to enable password protection, please refer to Security on page 26� ® ► If you see a dialog box indicating that your security settings prohibit running ActiveX ® Controls, please enable the ActiveX Controls for your browser� 1� Choose Tools > Internet Options > Security > Custom Level� ® 2. Loo
Resumen del contenido incluido en la página 15
VIVOTEK Using RTSP Players To view the MPEG-4 streaming media using RTSP players, you can use one of the following players that support RTSP streaming� Quick Time Player Real Player VLC media player 1 Launch the R � TSP player � mpegable Player 2. Choose File > Open URL. A URL dialog box will pop up. 3� The address format is rtsp://:/ As most ISP
Resumen del contenido incluido en la página 16
VIVOTEK Using 3GPP-compatible Mobile Devices To view the streaming media through 3GPP-compatible mobile devices, make sure the Network Camera can be accessed over the Internet� For more information on how to set up the Network Camera over the Internet, please refer to Setup the Network Camera over the Internet on page 8� To utilize this feature, please check the following settings on your Network Camera: 1� Because most players on 3GPP mobile phones do not support RTSP authentication, make
Resumen del contenido incluido en la página 17
VIVOTEK Using VIVOTEK Recording Software The product software CD also contains recording software, allowing simultaneous monitoring and video recording for multiple Network Cameras� Please install the recording software; then launch the program to add the Network Camera to the Channel list� For detailed information about how to use the recording software, please refer to the user’s manual of the software or download it from http://www�vivotek�com� User's Manual - 17
Resumen del contenido incluido en la página 18
VIVOTEK Main Page This chapter explains the layout of the main page. It is composed of the following sections: VIVOTEK INC� Logo, Host Name, Camera Control Area, Configuration Area, Menu, and Live Video Window� VIVOTEK INC. Logo Host Name Camera Control Area Live View Window Configuration Area VIVOTEK INC. Logo Click this logo to visit the VIVOTEK website� Host Name The host name can be customized to fit your needs. For more information, please refer to System on page 24� Camera Control Are
Resumen del contenido incluido en la página 19
VIVOTEK Live Video Window ■ The following window is displayed when the video mode is set to H264 / MPEG-4: � MPEG-4 Protocol and Media Options Video Title Time 2011/05/13 13:44:17 Title and Time Video 13:44:17 2011/05/13 Video Control Buttons Video Title: The video title can be configured. For more information, please refer to Video Settings on page 51� H264 / � MPEG-4 Protocol and Media Options: The transmission protocol and media options for H264 / � MPEG-4 video streaming. For
Resumen del contenido incluido en la página 20
VIVOTEK Full Screen: Click this button to switch to full screen mode� Press the “Esc” key to switch back to normal mode� ■ The following window is displayed when the video mode is set to MJPEG: Video Title 2011/05/13 13:44:17 Time Title and Time Video 13:44:17 2011/05/13 Video Control Buttons Video Title: The video title can be configured. For more information, please refer to Video Settings on page 51� Time: Display the current time� For more information, please refer to Video Settings
