Resumen del contenido incluido en la página 1
00403A Cover_SSC-17TQ 10/9/03 11:31 AM Page 1
COLOR DUAL QUAD
OBSERVATION SYSTEM
SSC-17TQ
INSTALLATION
MANUAL
POWER
Resumen del contenido incluido en la página 2
00403A SSC-17TQ_ENG 10/9/03 11:30 AM Page e-2 8A. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven CAUTION surfaces may cause the appliance and cart combination to overturn. RISK OF ELECTRIC SHOCK 9. Ventilation : Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of DO NOT OPEN the video product and to protect it from overheating, and these openings must not be blocked or covered. The openings s
Resumen del contenido incluido en la página 3
00403A SSC-17TQ_ENG 10/9/03 11:30 AM Page e-4 Contents Chapter 3: Setting each item function at SETUP MENU IMPORTANT SAFEGUARDS...................................................e-2 3-1) CLOCK/DISPLAY SET MENU function setting .............e-30 e-4 e-5 3-2) CHANNEL TITLE MENU function setting .....................e-31 3-3) SYSTEM SET MENU function setting ............................e-32 3-4) EVENT SET MENU function setting ..............................e-34 Chapter 1: System Components and
Resumen del contenido incluido en la página 4
00403A SSC-17TQ_ENG 10/9/03 11:30 AM Page e-6 1-2) System Components Chapter 1: System Components and Installation The system consists of the following: 1-1) Environmental requirements for installation and safety e-6 e-7 This section describes the environmental requirements for safe installation and use. Install the product on a flat table or in a rack. It should be used only when level and should not be used when stood vertically or obliquely. The location in which the main system is inst
Resumen del contenido incluido en la página 5
00403A SSC-17TQ_ENG 10/9/03 11:30 AM Page e-8 1-3) CAMERA composition and installation method ITEM MODEL DESCRIPTION Q’ty NOTE LCD MONITOR SMT-170 17" TFT-LCD MONITOR 1 - 1) Standard Camera composition (SOD14C) DIGITAL DUAL QUAD SOQ-080N DIGITAL DUAL COLOR 1 - QUAD SWITCHER e-8 e-9 STANDARD CAMERA SOD14C NORMAL TYPE CAMERA 2 - PIR CAMERA SMM- PIR CAMERA 1 Tapping Screw 4 PIRCAM (HUD 5=2, BH M3 x 30=2) CAMERA BRACKET SBR-110 STANDARD TYPE 2 Tapping Screw 6 CAMERA BRACKET (M4 x L15) CAMERA
Resumen del contenido incluido en la página 6
00403A SSC-17TQ_ENG 10/9/03 11:30 AM Page e-10 f. Speaker 3) PIR Camera composition It outputs the sound signal which was transfered from the monitor. • PIN configuration of the PIR CAMERA is the same as the STANDARD e-10 e-11 CAMERA. • But, PIR CAMERA does not provide ALARM JACK. 3 2) INSTALLING STANDARD CAMERA (SOD14C) SOD14C s camera can be attached to the wall, ceiling or shelf using the camera mount bracket (SBR-
Resumen del contenido incluido en la página 7
00403A SSC-17TQ_ENG 10/9/03 11:30 AM Page e-12 6-pin modular jack Used to connect the camera to the monitor. 1> Vertical Detection Line e-12 e-13 PIN NUMBER SPEC ! SPEAKER(HOT) @ VIDEO_OUT # GND $ SPEAKER(COLD) % AUDIO_OUT/ALARM_OUT ^ 12V DC • Please consider the horizontal detection area and the vertical detection line when choosing an installation site. 5-Pin Terminal Block A terminal block for supplying backup power for the PIR sensor operation during p
Resumen del contenido incluido en la página 8
00403A SSC-17TQ_ENG 10/9/03 11:30 AM Page e-14 Camera installation Hints 1. Do not install directly towards rising or setting sun. Can cause burn or damage to internal options. 2. Do not limit desired detection zone by interference of curtains, screens, potted plants, etc. 3. Also, do not locate it in front of source of water/oil vapors. Avoid placement of heat source inside 6 8 e-14 e-15 detection zone 7 4. Do not install outdoors. 9 Function Switch A function switch for the PIR sen
Resumen del contenido incluido en la página 9
00403A SSC-17TQ_ENG 10/9/03 11:30 AM Page e-16 4) INSTALLING THE PIR CAMERA (SMM-PIRCAM) 4. Connect the Camera connector(RJ-11) cable to the case-rear as well as the cable to be connected to 1. Choose an installation site that can sufficiently support 5 times the weight of the equipments to be the terminal. installed. 2. Remove the screw (BH M2.6) at the bottom of the main unit by turning it counterclockwise, and e-16 e-17 then lift the assy-case front as you push it upward to detach it from
Resumen del contenido incluido en la página 10
00403A SSC-17TQ_ENG 10/9/03 11:30 AM Page e-18 6. Adjust the direction of the lens. 4) CAMERA MOUNT BRACKET(SBR-110) & STANDARD CAMERA(SOD14C) 1) Use the cross (+) screw driver to turn the screw (indicated by the arrow in the illustration) counterclockwise slightly. The lens body will move. (1) Overview 2) Tilt the lens body down about 10° from the horizontal, and then turn the screw clockwise to fasten CAMERA MOUNT BRACKET (SBR-110) is used to attach the camera to a wall, ceiling or shelf.
Resumen del contenido incluido en la página 11
00403A SSC-17TQ_ENG 10/9/03 11:30 AM Page e-20 1-4) CAMERA Composition and Connecting Method to • Loosen the handle by turning it in a counterclockwise direction and then adjust the camera SYSTEM position . Tighten the handle, turning it clockwise, and lock the camera in position. After positioning monitor and installing three cameras to a desired location, please connect CAMERA e-20 e-21 to SYSTEM through CAMERA CABLE (MCB-60 or MCB-100) as shown in the below figure. Please • Connect the
Resumen del contenido incluido en la página 12
00403A SSC-17TQ_ENG 10/9/03 11:30 AM Page e-22 f) Connect the A/O (HOT) terminal on the rear panel to the Alarm IN terminal of the VCR. 1-5) External terminal connecting method for CAMERA and g) Connect the A/O (COLD) terminal on the rear panel to the Ground terminal of the VCR. SYSTEM h) Connect the A/R terminal on the rear panel to the Alarm Reset terminal of the VCR. 1) External terminal connecting method for CAMERA i) Connect the G (ground) terminal on the rear panel to the Ground term
Resumen del contenido incluido en la página 13
00403A SSC-17TQ_ENG 10/9/03 11:30 AM Page e-24 1-7) REAR Panel function 1-8) Mounting the DIGITAL DUAL QUAD (SOQ-080N) ACCESSORY e-24 e-25 Screws (BH M3X6, 4EA) Screws (TH M4X20, 4EA) Rack Mount Adapters (2EA) a. CAMERA IN (RJ-11) Video camera input terminals. You Can connect up to 8 Cameras with RJ-11 connectors. 1) Assemble the fixing holes of the b. CAMERA OUT (BNC) BRACKET-GUIDE to the fixing grooves Video Camera out terminals. underneath both sides of the ASSY CABINET-BOTTOM, and
Resumen del contenido incluido en la página 14
00403A SSC-17TQ_ENG 10/9/03 11:30 AM Page e-26 2-4) SET- KEY Chapter 2: REMOTE CONTROL Alarm function and loss function can be cancelled Function and Using Method while the alarm or loss is working. e-26 e-27 The Remote Controller(REMOCON) is contained in the 17" TFT-LCD Monitor (SMT-170). 2-5) QUAD/PAGE- KEY 2-1) TALK KEY Allows users to display QUAD A or QUAD B at QUAD DISPLAY MODE. TALK KEY allows users to transmit voice signal to • QUAD A: QUAD DISPLAY MODE from Camera intended camera by
Resumen del contenido incluido en la página 15
00403A SSC-17TQ_ENG 10/9/03 11:30 AM Page e-28 2-7) PIP- KEY 2-12) ENTER- KEY Can be used to see the main screen while Single screen is displayed. The main screen can be changed As a multi functional ENTER key, it is used for 1. entering from the menu into the submenu, 2. moving and transfered to another channel while PIP is working. Please refer to "CHAPTER 4. DISPLAY into the full screen of selected channel. e-28 e-29 MODE SETTING" for PIP function and details. 2-13) MENU- KEY 2-8) FREEZE-
Resumen del contenido incluido en la página 16
00403A SSC-17TQ_ENG 10/9/03 11:30 AM Page e-30 DATE TYPE: MM/DD/YY YY/MM/DD DD/MM/YY. Chapter 3: Setting each item function at SETUP DATE [MM/DD/YY] • Month(MM) : 01 ~ 12 MENU • Day(DD) : 01 ~ 31 Pressing the MENU BUTTON of the FRONT PANEL allows users to enter SETUP MENU and see the e-30 • Year(YY) : 00(2000) ~ 99(2099) e-31 following menu OSD box. Setting method of each SETUP MENU function and operation is as follows. TIME [HH:MM:SS] [SETUP MENU] • Hour(HH) : 00 ~ 23 1. CLOCK/DISPLAY SET •
Resumen del contenido incluido en la página 17
00403A SSC-17TQ_ENG 10/9/03 11:30 AM Page e-32 PIP POSITION: BOTTOM-RIGHT TOP-LEFT TOP-RIGHT BOTTOM-LEFT. 3-3) SYSTEM SET MENU function setting • Select the PIP position among the four options listed above. You may change DWELL TIME, PIP POSITION, BORDER COLOR, LOSS CHANNEL COLOR, BORDER COLOR: GRAY WHITE BLACK. SYSTEM ID. e-32 • GRAY : BORDER LINE COLOR is displayed in GRAY in Multi Screen mode e-33 If you click the UP/DOWN button to select 3. SYSTEM SET in the SETUP MENU and click the
Resumen del contenido incluido en la página 18
00403A SSC-17TQ_ENG 10/9/03 11:30 AM Page e-34 3-4) EVENT SET MENU function setting EVENT DETECT... You may change EVENT HOLD TIME, EVENT BUZZER, EVENT DETECT. • Select “EVENT DETECT...” with the UP/DOWN button and click the ENTER button. If you click the UP/DOWN button to select 4. EVENT SET in the SETUP MENU and click the e-34 e-35 Then the following screen pops up. ENTER button, the following screen will be displayed. [EVENT SET] [EVENT DETECT] EVENT HOLD TIME 01 [MIN] CH ALARM LOSS EVEN
Resumen del contenido incluido en la página 19
00403A SSC-17TQ_ENG 10/9/03 11:30 AM Page e-36 3-5) EVENT LIST MENU function setting Chapter 4: DISPLAY MODE setting method You can check the ALARM/LOSS EVENT LIST. If you click the UP/DOWN button to select 5. EVENT LIST in the SETUP MENU and click the ENTER button, the following screen will be e-36 4-1) SINGLE SCREEN DISPLAY e-37 displayed. The initial display mode is QUAD A mode. Use the UP and DOWN buttons to select the channel you [EVENT LIST]
Resumen del contenido incluido en la página 20
00403A SSC-17TQ_ENG 10/9/03 11:30 AM Page e-38 4-2) QUAD MODE DISPLAY 4-3) AUTO SEQUENTIAL DISPLAY MODE Users can switch SINGLE DISPLAY MODE and SEQUENTIAL DISPLAY MODE to QUAD Pressing on the SEQUENCE KEY on the front allows screen to automatically switch to SINGLE DISPLAY MODE, or QUAD A (QUAD B) to QUAD B (QUAD A), or PIP MODE to QUAD MODE, MODE full screen or QUAD MODE. (‘no-signal’ channels will be skipped while single screen is e-38 e-39 press the QUAD/PAGE KEY. auto-switching.)
