Resumen del contenido incluido en la página 1
SNC-B5399(P)
Network Camera
User Manual
imagine the possibilities
Thanks you for purchasing this Samsung product.
To receive a more complete service, please visit
our website
www.samsungsecurity.com
RoHS compliant
Our product complies with “The Restriction Of the use of certain Hazardous Substances in electrical
and electronic equipment”, and we do not use the 6 hazardous materials- Cadmium (Cd), Lead
+6
(Pb), Mercury (Hg), Hexavalent Chromium (Cr ), Poly Brominated Biphenyls (PBBs), Poly Bro
Resumen del contenido incluido en la página 2
overview CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit. WARNING To reduce the risk of fi re or electri
Resumen del contenido incluido en la página 3
● OVERVIEW 7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fi re or electric shock. 8. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fi re or electric shock. 9. If this product fails to operate normally, contact the nearest service center. Never disassemble or modify this product in any way. (SAMSUNG i
Resumen del contenido incluido en la página 4
overview CAUTION 1. Do not drop objects on the product or apply strong blows to it. Keep away from a location subject to excessive vibration or magnetic interference. 2. Do not install in a location subject to high temperature (over 50°C), low temperature (below -10°C), or high humidity. Doing so may cause fi re or electric shock. 3. If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it. 4. Remove the power plug from the outlet when
Resumen del contenido incluido en la página 5
● OVERVIEW FCC STATEMENT This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions : 1) This device may not cause harmful interference, and 2) This device must accept any interference received including interference that may cause undesired operation. Caution This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of FCC Rules. These limits are designed to provide reasonable protecti
Resumen del contenido incluido en la página 6
overview IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifi ers) that produce heat. 9. Do not defeat the safety purpose of the p
Resumen del contenido incluido en la página 7
● OVERVIEW CONTENTS 6 Important Safety Instructions OVERVIEW 9 Product Features 9 Recommended PC Specifi cations 10 What’s Included 2 11 At a Glance 14 Disassembling INSTALLATION & 15 Inserting/Removing an SD CONNECTION Memory Card 16 Memory Card Information (not included) 14 17 Connecting with other Device 21 Installation 21 Optional Accessories for Installation 27 How to use the menu key CAMERA SETUP 28 Main Menu 28 Profi le 29 Camera Setup 27 33 Privacy Zone 34 Others 35 System Info 35 Lan
Resumen del contenido incluido en la página 8
overview 47 Connecting to the camera WEB VIEWER 48 Login 49 Installing ActiveX 50 Using the Live Screen 47 51 Backup 54 Using the SD Search Viewer Screen 55 Accessing the Setup screen SETUP SCREEN 55 Default Setup 60 System Setup 64 Overlay Setup 55 65 Event Setup 72 Network Setup 73 Profi le APPENDIX 74 Terminology 76 Specifi cations 80 Frame Rate (NTSC) 73 86 Frame Rate (PAL) 92 Troubleshooting 8_ overview
Resumen del contenido incluido en la página 9
● OVERVIEW PRODUCT FEATURES Support various communication protocols Supports TCP/IP, UDP, RTP/RTSP, SMTP for email, and FTP protocols as well as various internet protocols such as ARP, HTTP, HTTPS and DHCP. Web Browser-based Monitoring Using the Internet web browser to display the image in a local network environment. Automatic Local IP Setup Even a network novice can install it with minimum operations. Alarm If an alarm sensor is connected and it detects a motion, a message is sent to the
Resumen del contenido incluido en la página 10
overview WHAT’S INCLUDED Please check if your camera and accessories are all included in the product package. Image Part name Standard Quantity Usage Camera SNC-B5399 1 User Manual/ CD IP INSTALLER 1 S/W User 1 Manual Used to connect to a monitor for camera Cable for operation test. test monitor 1 For connecting to a surveillance monitor, use connection BNC cable. Used to fix the screws, for installation Insert Plastic HUD 5 4 the anchor into a drilled hole (to reinforce the Anchor streng
Resumen del contenido incluido en la página 11
● OVERVIEW AT A GLANCE Appearance 6 Item Description Dome Cover Dome cover for the lens and unit protection. Operates if ambient temperature drops below 5°C, for defrosting the dome Heater cover. Main unit Main unit includes the lens, switch board, PCB boards and screws. Power Port Used to plug the power cable. Connects to the video input terminal of a monitor, which outputs the video Video Out Jack signal from the camera. Audio In Jack Used to connect to a microphone. Audio Out Jack Used to
Resumen del contenido incluido en la página 12
overview Inside 3 4 Item Description Network Port Used to connect a PoE or LAN cable. Alarm in/out terminals can be configured as follows: - ALARM IN : Terminal for Alarm Input. Alarm In / Out terminals - ALARM OUT : Terminal for Alarm Output. - GND : Grounding terminal. SD Memory Card Compartment for the SD memory card. Compartment Resets the camera settings. Press the button for about 3 seconds, and the system indicator turns off and will restart. Reset Button J Resetting the camera requir
Resumen del contenido incluido en la página 13
● OVERVIEW Components 3 4 5 6 Item Description Inner Cover Cover for the main unit’s protection. Side wing hooks By lifting it while gently pressing the both ends, you can separate the inner cover. Using the test monitor cable, you can connect to a mobile display for camera Monitor Out test. ZOOM lever You can adjust or fix the zoom ratio Turn the barrel left or right to adjust the focus, and turn the knob clockwise to Focus lever lock the focus. To separate the bracket from the main unit for
Resumen del contenido incluido en la página 14
installation & connection DISASSEMBLING To connect the alarm in/out, the dome cover and lens cover are to be separated. 1. Using the L-wrench provided, loosen 3 screws by turning them counterclockwise and separate the dome cover. 2. Lift up the inner cover while gently pressing its both ends to separate it from the unit. 14_ installation & connection
Resumen del contenido incluido en la página 15
● INSTALLATION & CONNECTION INSERTING/REMOVING AN SD MEMORY CARD Inserting an SD Memory Card Push the SD memory card in the direction of the arrow shown in the diagram. Do not insert the SD memory card while it’s upside down by force. Otherwise, it may damage the J SD memory card. Removing an SD Memory Card Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot. Pressing too hard on the SD memory card can cause the card to sh
Resumen del contenido incluido en la página 16
installation & connection MEMORY CARD INFORMATION (NOT INCLUDED) What is a memory card? The memory card is an external data storage device that has been developed to offer an entirely new way to record and share video, audio, and text data using digital devices. Selecting a memory card that’s suitable for you Your camera supports SDHC memory cards. You may, however, experience compatibility issues depending on the model and make of the memory card. Your camera supports SD memory cards. Note th
Resumen del contenido incluido en la página 17
● INSTALLATION & CONNECTION CONNECTING WITH OTHER DEVICE Power Monitor Power Supply Connect the power adaptor and camera’s power in jack. Be careful not to reverse the polarity when you connect the power cable. J You can also use a router featuring PoE (Power over Ethernet) to supply power to the camera. Connecting to the monitor Connect the camera’s Video Out jack and the monitor’s video in jack. English _17
Resumen del contenido incluido en la página 18
installation & connection Connecting to Audio Input/Output Microphone LINE-OUT Microphone LINE-IN Speaker 1. Connect the AUDIO IN port of the camera with the microphone directly or LINE OUT port of the amplifi er that the microphone is connected to. Direct Mic Connection : Set Audio Input Gain high (10). (Refer to page 56) Line Out Connection : Set Audio Input Gain low (1). (Refer to page 56) 2. Connect the AUDIO OUT port of the camera with the LINE IN port of the speaker. 18_ installation & c
Resumen del contenido incluido en la página 19
● INSTALLATION & CONNECTION Audio I/O Block Diagram Network Microphone Speaker Audio Codec G.711 PCM. µ-law 64kbps 8kHz sampling Full duplex Audio Audio in Used for mono signal line input (Max.2.4 Vpp) Audio out Used for mono signal line output (Max.2.4 Vpp) Line out impedance 600 English _19
Resumen del contenido incluido en la página 20
installation & connection Connecting to the I/O port box Connect the Alarm I/O cable to the corresponding port of the inner port box. 5 4 3 2 1 1,2 : ALARM IN 1,2 3 : GND 4,5 : ALARM OUT 1,2 ALARM IN 1, 2 : Used to connect the alarm input signal. GND : Used for earth-grounding. ALARM OUT 1, 2 : Used to connect the alarm output signal. Alarm I/O Wiring Diagram ALARM IN 1 1 ALARM IN 2 2 GND 3 External Relay ALARM OUT 1 4 External Relay ALARM OUT 2 5 20_ installation & connection
