Resumen del contenido incluido en la página 1
®
SS20, SS22,
SS2000, SS2002
Series
Discreet
Surveillance
Enclosures
Installation/
Operation Manual
C429M-B (2/98)
U
® L
LISTED
Pelco • 300 W. Pontiac Way, Clovis • CA 93612-5699 USA • Pelco Online @ http://www.pelco.com
In North America and Canada: Tel (800) 289-9100 or FAX (800) 289-9150 • DataFAX (800) 289-9108
International Customers: Tel (1-559) 292-1981 or FAX (1-559) 348-1120 • DataFAX (1-559) 292-0435
Resumen del contenido incluido en la página 2
CONTENTS Section Page 1.0 GENERAL ..................................................................................................3 1.1 IMPORTANT SAFEGUARDS AND WARNINGS ............................... 3 2.0 DESCRIPTION .......................................................................................... 4 2.1 MODELS ............................................................................................ 4 3.0 INSTALLATION ..............................................................
Resumen del contenido incluido en la página 3
1.0 GENERAL 1.1 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be CAUTION: This device is observed. designed to operate at 24 volts AC power. Input volt- 1. Installation and servicing should only be done by Qualified Service Personnel ages must not exceed 28 and conform to all Local codes. volts or drop below 22 volts, or else damage the the 2. Unless the unit is specifically marked as a NEMA Type 3, 3R, 3S, 4, 4X, 6, or motors wi
Resumen del contenido incluido en la página 4
2.0 DESCRIPTION Pelco’s SS20/SS22/SS2000/SS2002 Series domes are full-sphere, discreet sur- veillance enclosures designed to be suspended from ceilings and to compliment the interior design of businesses, hotels, and offices. The black opaque (or chrome) lower dome effectively camouflages a CTTV security/ surveillance system without compromising the quality of the video picture. Options for the SS2000/SS2002 include a standard pan/tilt, pan/tilt with continuous 360° pan rotation (SL), or prese
Resumen del contenido incluido en la página 5
3.0 INSTALLATION Save the shipping carton and plastic packing in case the unit has to be returned for credit or repair. 3.1 CONDUCTOR AND CABLE REQUIREMENTS A minimum of 11 conductors plus coax is required, which includes common re- NOTE: The following are cable re- quirements for motorized zoom lens and camera AC power. quirements. A relay box (RB24) is available to extend the operating dis- Non-PP Models tance up to 13,000 feet (3,962 m) over 16 Awg wire. 11 Conductor 12 Conductor* 18 Awg 22
Resumen del contenido incluido en la página 6
Figure 2. SS2000/SS2000-SL/SS2002-SL Wiring Diagram 6 Pelco Manual C429M-B (2/98)
Resumen del contenido incluido en la página 7
Figure 3. SS2000-PP Wiring Diagram Pelco Manual C429M-B (2/98) 7
Resumen del contenido incluido en la página 8
Figure 4. SS2000SL-PP Wiring Diagram 8 Pelco Manual C429M-B (2/98)
Resumen del contenido incluido en la página 9
3.2 CONNECTOR ASSEMBLY NOTE: Contacts cannot be removed To install and test the SS2000/SS2002 Series dome you will need to assemble the connector parts provided. Fabricate the interconnecting cable as outlined below from the connector without the use (see Figure 5): of an AMP extraction tool, part num- ber ZT305183 (for 9-, 14-, or 16-pin 1. Slide the cable clamp (part A , item 1) over the cable with the threaded end connector) or ZT91067-2 (for 28-pin facing the connector (item 5). connector)
Resumen del contenido incluido en la página 10
CABLE, 12 COND. @ 6' WIR201912 COAX @ 6' WIRRG59/U9259 CONCP88-2 14-POS RECEPTACLE CRIMP SOCKET CABLE CLAMP CON206403-3 CON66105-2 CON206070-1 POSITION COLOR FUNCTION 1 BROWN COMMON/PAN AND TILT 2 CORE COAX VIDEO 3 2 1 3 RED LEFT 4 SHIELD COAX VIDEO 7 6 5 4 5 YELLOW DOWN 6 ORANGE UP 11 10 9 8 7 BLUE RIGHT 14 13 12 8 GREEN GROUND 9 WHITE AC HIGH, CAMERA 10 BLACK IRIS FRONT VIEW 11 TAN (OR BLK/WHT) FOCUS 14-PIN CONNECTOR 12 PINK (
Resumen del contenido incluido en la página 11
3.3 MOUNTING The SS2000/SS2002 enclosure is designed to be suspended from a suitable length of 1-1/2" pipe threaded at both ends. This pipe can be interfaced to either a Pelco MRWA wall adapter, MRCA ceiling adapter, or coupled to a longer length of pipe. Refer to Figure 8 for mounting configurations. STRUCTURAL CEILING MOUNTING DROP CEILING MOUNTING WALL MOUNTING Figure 8. Mounting Configurations Pelco Manual C429M-B (2/98) 11
Resumen del contenido incluido en la página 12
3.4 DOME INSTALLATION To install your dome system, perform the following steps (refer to Figure 9): 1. Select the appropriate pipe length and mounting method. If the MRCA or MRWA mount is used, tighten the pipe to approximately 30 ft lb, then tighten the 8-32 screw in the pipe nut to lock the pipe threads. Slide the upper dome onto the pipe and lock it out of the way with a suitable retainer. 2. Screw the mounting flange (item 4) onto the pipe and tighten securely (ap- proximately 20 ft lb). T
Resumen del contenido incluido en la página 13
4.0 EXPLODED ASSEMBLY DIAGRAM Table A. SS2000/SS2002 Exploded Assembly Diagram Item Qty Description Part Number 1 1 Dome, upper SS200010000 2 1 Dome, lower, Black (Opaque) SS200010001* Dome, lower, Chrome (Opaque) SS2012000* 3 1 Bracket, drive SS20004007COMP 4 1 Bracket, upper SS20001000COMP 5 1 Bracket, lower SS20004008COMP 6 48 Velcro, black, 5/8" wide x inch (not shown) TV10002 7 50 Velcro, black, 5/8" wide x inch (not shown) (SS22 & SS2002-SL) TV10003 56 Velcro, black, 5/8" wide x inch (no
Resumen del contenido incluido en la página 14
Figure 9. SS2000/SS2002 Exploded Assembly Diagram 14 Pelco Manual C429M-B (2/98)
Resumen del contenido incluido en la página 15
5.0 ADJUSTMENTS To adjust the pan/tilt limits, perform the following steps. Refer to Figure 10 for limit stop locations. CAUTION: Do not attempt Factory pan limits are set to 0-355° and tilt limits are set to 0-90° (horizontal to vertical). Under normal conditions, the tilt limits should not have to be reset. To to adjust limit stops when adjust limit stops, perform the following steps: the pan/tilt is in operation. Damage to the equipment 1. Pan to the right using the joystick control until t
Resumen del contenido incluido en la página 16
6.0 MAINTENANCE Clean the acrylic lower dome as necessary to maintain a clear picture. Be careful not to scratch the surfaces of the dome. Exterior Surface - Clean the dome's exterior surface with a nonabrasive cleaning cloth and cleaning agent that is safe for acrylic plastic. Either liquid or spray cleaner/ wax suitable for fine furniture is acceptable. Interior Surface (Except Chrome) - Clean the same as the exterior surface. Interior Surface (Chrome) - The inside surface of a chrome dome is
Resumen del contenido incluido en la página 17
7.0 SPECIFICATIONS ELECTRICAL Input Voltage: 24 VAC required for pan/tilt Running Current Pan: 0.31 amp (7.44 vA) Tilt: 0.38 amp (9.12 vA) Connectors Pan/Tilt: Amp CPC type (mate supplied) Lens: Hirschmann MAB6100 Video: BNC Camera Power: Spade lugs Motors: Two-phase induction type, instantaneous reversing Limit Switches Pan: 5 amp, (external adjustment) Tilt: 5 amp, (external adjustment) Conductor Requirements as listed, plus coax cable: Non-PP models: Pan/tilt (5 plus ground), Lens (4), Came
Resumen del contenido incluido en la página 18
GENERAL Maximum Camera/ Lens Length: 12.5 inches (31.75 cm) Ambient Temperature Range: 35°F to 120°F (1.6°C to 48.8°C) Construction Upper dome: Black, high-impact plastic, ABS Lower dome: Acrylic hemisphere with distortion-free viewing window with light attenuation factor of 1 f-stop; model SS2002-SL has 2 f- stop light attenuation factor. Rotates with pan/tilt and camera/ lens Dimensions: See Figure 1 Weight Model SS20/ SS22: 7 lb All other models: 14 lb 13 oz Shipping Weight Model SS20/ SS22:
Resumen del contenido incluido en la página 19
NOTES Pelco Manual C429M-B (2/98) 19
Resumen del contenido incluido en la página 20
8.0 WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Excep- tions to this warranty are as noted below: • Three years on Genex™ Series multiplexers. • Two years on all standard motorized and fixed focal length lenses. ® ® • Two years on Legacy , Intercept , PV1000 Series, CM6700/CM8500/CM9500/ ™ CM9750/CM9760 Matrix, Spectra , DF5 Series and DF8 F
