Resumen del contenido incluido en la página 1
WV-CP470 CP470
CP470
CP470
CP470
Color CCTV Cameras
Operating Instructions
Model No. WV-CP470
WV-CP474
(Lens: Option)
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
N1101-1121 V8QA5915BN Printed in Japan
N 19
For U.S.A
NOTE: This equipment has been tested and
found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC
CAUTION Rules. These limits are designed to provide
reasonable
Resumen del contenido incluido en la página 2
FEATURES 1. The following functions are built in. (1) Auto Light Control (ALC)/Electronic Light Control (ELC) (2) The SUPER-D2 function eliminates interference by strong background lighting which makes the camera picture dark, such as a spotlight. Dynamic range of 46 dB. (3) Various External Sync Functions, including Gen-Lock (4) Auto/Manual White Balance Function (5) Electronic Shutter Function 2. Signal-to-noise ratio of 50 dB (Equivalent to AGC Off) 3. Minimum Illumination of 0.8 lx (0.08 foo
Resumen del contenido incluido en la página 3
!6 Day/Night Input Terminal (DAY/NIGHT IN/GND) This terminal is used for connecting the camera to an external day/night detecting sen- sor. !7 AC Inlet Socket Plug the power cord (supplied as a standard accessory) into this socket and connect it to an AC outlet. !8 AC/DC Compatible Input Terminal (DC 12 V IN/AC 24 V IN) This terminal is for connecting the 12 V DC or 24 V AC power supply cord. Note: Do not exceed the ratings of the voltage or current when connecting the external device. Cautions:
Resumen del contenido incluido en la página 4
WV-CP470 CP470 WV-CP470 CP470 CP470 MOUNTING LENS/FOCUS ADJUSTMENT The following installation should be a made by qualified service personnel or system installers. Installation of Auto Iris Lens Connector Install the lens connector (YFE4191J100) when using a video drive ALC lens. (1) Cut the iris control cable at the edge of the lens connector to remove the existing lens connector and then remove the outer cable cover as shown in the figure below. The pin assignment of the lens connector is as f
Resumen del contenido incluido en la página 5
SETUP 1. CAMERA SETUP MENU This camera utilizes an on-screen user setup menu. • Opening the Setup Menu Press and hold down I for 2 seconds or Highlighted more. ** CAM SET UP ** CAMERA ID OFF ALC/ELC ALC The CAM SET UP menu appears on the SHUTTER --- AGC ON(DNR-H) monitor as shown in the figure. SENS UP OFF Check the current settings on the menu. SYNC INT WHITE BAL ATW1 MOTION DET OFF LENS DRIVE DC END SET UP DISABLE Refer to the foll
Resumen del contenido incluido en la página 6
SETTING PROCEDURES 1. Camera Identification (CAMERA ID) Setting You can use the camera identification (CAMERA ID) to assign a name to the camera. The camera ID consists of up to 16 alphanumeric characters. The camera ID display can be switched on or off on the monitor screen. To edit the CAMERA ID 1. Move the cursor to CAMERA ID. The factory default setting is OFF. 2. Press I. The CAMERA ID menu Character Cursor appears. The cursor on the letter “0” is 0123456789 highlighted. ABCDEFGHI
Resumen del contenido incluido en la página 7
SETTING PROCEDURES 2-2. ALC Mode with SUPER-D2 OFF and ELC Mode Note: If ELC is selected, set MASK SET according to this procedure. 1. Move the cursor to SUPER-D2 and select OFF. (When you select ELC, ** ALC CONT ** SUPER-D2 is not available.) The MASK BACK LIGHT COMP SET appears on the menu. SUPER-D2 OFF MASK SET LEVEL ...I..... - + 2. Move the cursor to MASK SET and RET END press I. The 48 mask areas appear on the monitor screen. The cursor is blinking in
Resumen del contenido incluido en la página 8
6. Synchronization Setting (SYNC) You can select internal sync (INT) mode or line-lock (LL) mode. Additionally, this model accepts the VBS signal (composite color video or blackburst signal) and VS signal (B/W composite video or composite sync signal). The VD2 signal (multiplexed vertical drive sig- nal) with the composite video output signal from external equipment such as a matrix switcher is also acceptable. Whenever the VD2 signal is supplied to this camera, the camera automatically switches
Resumen del contenido incluido en la página 9
5. Supply the video output signal of the ** SYNC ** camera to be adjusted and the refer- ence gen-lock input signal to a dual- H PHASE ........I - + trace oscilloscope. 6. Set the oscilloscope to the horizontal rate and expand the horizontal sync portion on the oscilloscope. RET END 7. Move the cursor to H PHASE. 8. Adjust the horizontal phase by press- ing L or M. The adjustable range is 0-2.0 µs. 6-3. Line-lock Sync Mode (LL) Note: The line-lock (LL) sync mode is
Resumen del contenido incluido en la página 10
Manual Fine Adjustment for AWC (ATW) You can set the white balance items manually. 1. To set MASK SET, proceed as described in steps 2 to 4 of “ALC mode with SUPER-D2 OFF and ELC mode”. 2. Move the cursor to R. 3. Press L or M to obtain the optimum amount of red gain. 4. Move the cursor to B. 5. Press L or M to obtain the optimum amount of blue gain. Note: When you need to set MASK SET, re-adjust to obtain the optimum amount of red and blue gain. 8. Motion Detector Setting (MOTION DET) The motio
Resumen del contenido incluido en la página 11
1. Move the cursor to BW. 2. Select AUTO1, AUTO2, EXT, ON or OFF using L or M. AUTO1: The camera selects black and white mode if the picture is dark, or color mode if the picture is bright enough. Note: Color picture switches to black-and-white picture and vice versa in approxi- mately 1 or 2 minutes after detection of illuminance. AUTO2: Applying AUTO1 may cause malfunction when using a source of near-infrared light at night because the illuminance changes significantly when switching between a
Resumen del contenido incluido en la página 12
SPECIFICATIONS Pick-up Device: 771 (H) x 492 (V) pixels, Interline Transfer CCD Scanning Area: 4.8 (H) x 3.6 (V) mm (Equivalent to scanning area of 1/3” pick-up tube) Scanning: 525 lines/60 fields/30 frames Horizontal: 15.734 kHz Vertical: 59.94 Hz Synchronization: Internal, Line-locked, External (VS/VBS) or Multiplexed Vertical Drive (VD2) selectable Video Output: 1.0 V[p-p] NTSC composite 75 Ω /BNC connector Horizontal Resolution: 480 lines (C/L), 570 lines (B/W) Signal-to-Noise Ratio: 50 dB
