Resumen del contenido incluido en la página 1
FIXED IR DOME CAMERA TK-T2101RU
FIXED IR DOME CAMERA TK-T2101RE
Instructions
Resumen del contenido incluido en la página 2
Resumen del contenido incluido en la página 3
Connect only one camera to the power line, AC24V/DC12V.Do not share the power line with other equipment. The power cable between power source and the camera must be under 3 m. Important Safety Information Warning and Operating Notes Installation and serving the camera should be performed only by qualified and experienced technicians to conform to all local codes and to maintain your warranty. WARNING! The use of CSA certified/ UL Listed Class 2 power adapters
Resumen del contenido incluido en la página 4
TABLE OF CONTENTS 1. Introduction .................................................................................. 3 1.1 Before You Begin ----------------------------------------------------------------- 3 1.2 Dimensions ----------------------------------------------------------------------- 3 1.3 Names of Camera Parts --------------------------------------------------------- 4 1.4 Routine Maintenance ------------------------------------------------------------ 4 2. Installation .............
Resumen del contenido incluido en la página 5
INTRODUCTION 1. Introduction The dome camera is ideal for indoor installation in commercial and residential environment. With 3-axis mount support, it provides flexible installation on a ceiling or wall even at an angle. 1.1 Before You Begin Please read this manual carefully before you install the dome camera. Keep this guide for future reference. 1.2 Dimensions 84mm 112mm 3 97mm
Resumen del contenido incluido en la página 6
INTRODUCTION 1.3 Names of Camera Parts a b Figure 1-1 Camera parts 1. Conduit hole used for surface run power/video connector 2. Bottom case 3. Camera housing 4. Dome cover 5. IR board a. AC 24V / DC 12V power input connector (red +, black -) b. Video output connector Note: See Figure 2-3 for camera board controls. 1.4 Routine Maintenance The dome cover is an optical part. Use a soft, dry cloth to remove any fingerprints • or dust. Clean the camera housing with a soft, dry cloth. For more st
Resumen del contenido incluido en la página 7
INSTALLATION 2. Installation 2.1 Disassembling the Camera Before you mount and adjust the camera, follow these steps to disassemble the camera. 1. Insert a coin or flat tool to the side hole and twist to remove the dome cover. 2. Remove the dome cover (#2). 1. Bottom case 2. Dome cover Figure 2-1 Disassemble the camera 5
Resumen del contenido incluido en la página 8
INSTALLATION 2.2 Connecting the wiring Refer to Figure 1-1 to connect the video connect output connector (#b) and 24 VAC/12 VDC power connector (#a). Caution: For DC power supply use, make sure the polarity is correct to avoid malfunction and / or camera damage. 2.3 Mounting the Camera 1. Attach the mounting template to the wall or ceiling. 2. Drill two holes, then insert the screw anchors (#1) into the holes. 3. Secure the bottom case to the wall or ceiling with the TP4 x 15 mm tapping scr
Resumen del contenido incluido en la página 9
INSTALLATION 2.4 Optional Camera Settings Refer to Figure 2-3 to locate the OSD joystick control on the camera board. Use the joystick to access the OSD menu and configure the camera settings as required. To use the OSD joystick control: Press the OSD joystick control straight down to enter the Main menu or a selected • item. Move the OSD joystick control UP, DOWN, LEFT and RIGHT to navigate through • menus and options. For further information on OSD settings, refere to the “3. OSD Settin
Resumen del contenido incluido en la página 10
INSTALLATION 2.5 Adjusting the Camera Position The dome camera has three axes for positioning the camera. While monitoring the picture on the monitor, adjust the camera position as follows: Horizontal Adjustment Rotate 3D assembly in the base. Do not turn assembly more than 360° as this may cause the internal cables to twist and disconnect or break. Before making horizontal adjustment, please adjust vertical adjustment to 90 degree (vertical) first. Vertical Adjustment After loosening th
Resumen del contenido incluido en la página 11
INSTALLATION 2.7 Completing the Installation Once all adjustments are done, attach and secure the camera housing: 1. Use a soft, lint-free cloth to wipe the dome cover clean and remove fingerprints. 2. Assemble the dome cover (#2) and the bottom case (#1). Figure 2-5 Completing the installation 9
Resumen del contenido incluido en la página 12
OSD SETTINGS 3. OSD Settings Use the OSD menu to set up the camera for optimum performance. LENS AUTO PRIVACY OFF SHUTTER/AGC AUTO DAY/NIGHT AUTO WHITE BAL ATW NR BACKLIGHT OFF CAMERA ID OFF PICT ADJUST SYNC INT ATR OFF LANGUAGE ENGLISH MOTION DET OFF CAMERA RESET NEXT BACK EXIT SAVE ALL EXIT SAVE ALL Figure 3-1 OSD Main Menu 3.1 Lens The LENS settings allows you to configure Lens and brightness. Options are AUTO (Auto Iris lens) and MANUAL. The default setting is AUTO. In the AUTO
Resumen del contenido incluido en la página 13
OSD SETTINGS If SHUTTER/AGC is set to MANUAL, the submenu is shown as below. The shutter speed is a variable from 1/50(1/60)sec to 1/10000sec and the AGC is selectable depending on your environment condition. MODE SHUT+AGC SHUTTER 1/50(1/60) AGC 6.0 Recommended settings according to the application: 1. Auto Exposure by Iris Control: Application: General Purpose, Indoor surveillance. This is default settings. • LENS: AUTO • SHUTTER/AGC: AUTO • HIGH LUMINANCE MODE: AUTO IRIS • 2. Auto
Resumen del contenido incluido en la página 14
OSD SETTINGS PUSH: When selected in the appropriate position, the whole area will perform • white balance. PUSH LOCK: When selected in the appropriate position, WHITE BALANCE will • perform once. 3.4 BACKLIGHT Set Backlight compensation function. It controls the light level to overcome sever backlight conditions. Available options include OFF, BLC or HLC (Highlight Compensation) mode. The default is OFF. If HLC is selected, HLC is activated automatically when the camera detects high- lu
Resumen del contenido incluido en la página 15
OSD SETTINGS Note: If you enable MOTION DET function, then PRIVACY function will support 4 zones only. REA SEL 1/8 TOP 000 BOTTOM 000 LEFT 000 RIGHT 000 COLOR 1 TRANSP 0.00 MOSAIC OFF 3.9 DAY/NIGHT The camera will automatically switch to B/W mode when the illumination is under a certain threshold. There is no need to adjust this setting. Under B/W mode, you can set BURST to be ON or OFF. 3.10 NR NR allows you to configure the DNR (Digital Noise Reduction) settings to reduc
Resumen del contenido incluido en la página 16
SPECIFICATIONS Signal System NTSC PAL Image System Image Pickup Device 1/3 type: IT CCD Effective Pixels (HxV) 976 (H) × 494 (V) 976 (H) × 582 (V) Electric 2:1 Interlace V: 59.94 Hz , H: 2:1 Interlace V: 50 Hz , H: Scanning System 15.734KHz 15.625 KHz Sync System Internal Horizontal Resolution 600 TV lines Bulit-in Lens f=2.8mm~10.5mm,F1.2 DC iris varifocal Horizontal:101.8°(wide)~27.4°(tele) View Angle Vertical:73.7°(wide)~20.6°(tele) IR Distance 15 m IR Wave length 850nm Minimum Illuminati
