Resumen del contenido incluido en la página 1
IP 99 Series
EVS110 1CH Video Server
EIP220 Network Camera
User’s Manual
Copyright © EverFocus Electronics Corp,
Version Release: Dec. 2008
Resumen del contenido incluido en la página 2
IP99 series Product Name: IP99 EverFocus Network Cameras Model Number(s): EVS110, EIP220 FCC Notice "Declaration of Conformity Information" This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential Installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed a
Resumen del contenido incluido en la página 3
IP99 series About this document All the safety and operating instructions should be read and followed before the unit is operated. This manual should be retained for future reference. The information in this manual was current when published. The manufacturer reserves the right to revise and improve its products. All specifications are therefore subject to change without notice. Safety Notice -These limits are designed to provide reasonable protection. This equipment generates, uses
Resumen del contenido incluido en la página 4
IP99 series power source ratings. Do not use the appliance in an extreme environment where high temperature or high humidity exists. Use the appliance at temperature within -10 ℃ ~ 50 ℃ / 14 ℉ ~ 122 ℉ and a humidity below 90%. The input power source for this appliance is 12VDC. Use only the recommended power supplies. Power supplies must comply with the requirement of the latest version of IEC60950-1. Substitutions may damage the unit or cause a fire or shock hazard. Electrostatic-se
Resumen del contenido incluido en la página 5
IP99 series For example: (This web site may change without notices.) http://www.microsoft.com/downloads 4
Resumen del contenido incluido en la página 6
IP99 series TABLE OF CONTENTS 1. STARTING THE CAMERA OR VIDEO SERVER ............................................. 7 1.1 INSTALL IP99 SEARCHER IN PC ............................................................................. 7 1.2 ASSIGN NEW IP ADDRESS (OPTIONAL) .................................................................. 7 1.3 ACCESSING THE CAMERA ...................................................................................... 8 1.4 RESET AND FACTORY DEFAULT .............
Resumen del contenido incluido en la página 7
IP99 series 3.12 PTZ SETTING ..................................................................................................... 26 3.13 ADMINISTRATOR ............................................................................................... 27 3.14 CHANGE PASSWORD .......................................................................................... 28 3.15 SPECIAL SETTING ............................................................................................... 28 3.16 M
Resumen del contenido incluido en la página 8
IP99 series 1. Starting the camera or video server 1.1 Install IP99 searcher in PC Though you can simply enter 192.168.1.99 in IP address bar to access camera when you connect to only one IP99 device.( Default IP address is: 192.168.1.99 Port is: 80). However, it is recommended that you use IP search to manage IP camera and encoder. Please insert CD to install IP99 searcher tool. After finishing installation, click “IP searcher” icon to find IP99 encoders and cameras. Click “Searc
Resumen del contenido incluido en la página 9
IP99 series Note: Please consult your network administrator for avoiding IP address conflict Diagram 1.2 Assign new IP address 1.3 Accessing the camera Double click selected camera in IP99 searcher or Enter IP address in IP address bar, as shown in diagram 1.3: Diagram 1.3 enter IP address Enter IP address and click Enter to confirm, login window will pop up as shown in diagram 1.4: Diagram 1.4 login window 8
Resumen del contenido incluido en la página 10
IP99 series In login window, enter user name and password, （default user name is admin, password is 11111111 ）. Click“Confirm ＂button to enter web window, as shown in diagram 1.5: Diagram 1.5 Camera Web page 1.4 Reset and Factory Default You can physically push” RST” button on IP99 camera or click “Default” on IP searcher to back to factory default. 2. IP99 system operation After entering to web window, a button shows on top right corner, click this button enter to an
Resumen del contenido incluido en la página 11
IP99 series 2.1 Add more videos If you wish to add one video display in the same web page, click “Add New” button, as shown in diagram 2.2: Diagram 2.2 Add video display 2.2 Change video resource You can change video resource and simultaneously view multiplies cameras and encoders at same time. Right click mouse on display center point and go to “Change Resource”. Then you would see the login page. Enter IP address, user name, password for the camera you w
Resumen del contenido incluido en la página 12
IP99 series 2.3. Edit and Change Display Layout 2.3.1 Edit layout If you wish to add more video displays, please click , then interface changes to ，you can freely set the layout of video display in this window. Enter the number of channels you want for each row. Use comma to separate them. And click to make the actual layout change. For example,”5 ，3，0”, “shows the following layout. As shown in diagram 2.4: Diagram 2.4 Display re-layout After editing layout, click “Save” butto
Resumen del contenido incluido en la página 13
IP99 series Diagram 2.5 Layout selection 2.4 Zoom in/zoom out 2.4.1 Integer zoom in/zoom out Click buttons at top right side of the page to zoom in or zoom out the entire screen. 2.3.2 Single display zoom in/zoom out To zoom in/zoom out single channel screen, direct the mouse to at top of that channel display, and click on , slide the tilt wheel of mouse to zoom in or zoom out video images. 2.4 Operating buttons There are 6 operating buttons at top right corner of every camer
Resumen del contenido incluido en la página 14
IP99 series Diagram 2.6 Record 2.4.2 Stop recording Method 1: Click on button located at top right corner of the image, it will stop recording immediately, button changes to . Method 2 ：Double click on the green area of , it returns to original color meaning that recording is stopped. 2.4.3 Snapshot Click button to snapshot the image ，default file path for the snapshot is ： C:\image99\... 2.4.4 Playback Click button ，playback window pops up as shown in diagram 2.7: Dia
Resumen del contenido incluido en la página 15
IP99 series Click “Search NVR ＂button to search the NVR device used for archiving recording files. If you do not have NVR device, please ignore this selection. Open the file to be played, click “Play ＂to play recorded video. Click fast forward button , to adjust playback speed. Click fast reverse button , to adjust reverse speed. Click pause button , to pause the video. Click play button , to stop playback, returning to normal page. Note: If you have problem when use windows vis
Resumen del contenido incluido en la página 16
IP99 series Note 2 ：PTZ control can also be preformed by using PC’s keyboard, please refer to section 5 of 2.4.7 for more details. Note3: PTZ control is functioning only if PTZ Function is set On in PTZ Setting, please refer to section 3.12. 2.4.6 On-Screen PTZ Control (for Video Server only) On Screen PTZ function is available when you connect PTZ to IP99 video server or use IP99 PTZ. a) Left click mouse in the view to move PTZ to the clicked direction b) Zoom in
Resumen del contenido incluido en la página 17
IP99 series Diagram 2.10 Display size 2） Change source: Click “Change source ＂to fill out information for the IP camera to be controlled, as shown in diagram 2.11: Diagram 2.11 Change source First row: Camera name Second row: IP address of camera to be connected Third row: User name Fourth row: Login password When you finish filling out, click on “Change ＂button to enter video display with setting changed. If you do not need to change those settings, please click “Abort” to ex
Resumen del contenido incluido en la página 18
IP99 series 4）Sound ON ：used to enable/disable sound transmission. 5）PTZ(for Video Server only) ：Click “PTZ ＂option which allows you to check keyboard keys of PC used to control speed dome, as shown in diagram 2.13: Diagram 2.13 PTZ contraol keys and functions 6）File .av to AVI ：Click “File .av to AVI ＂option, select .av file to be converted and click “Confirm” to save it as AVI format. Diagram 2.14 File .av to AVI confirmation dialogue box Note ：AVI is the most w
Resumen del contenido incluido en la página 19
IP99 series Diagram 3.1 status information 3.2 Video/audio setting Select 2. Video & Audio from the drop-down menu at top right corner, as shown in diagram 3.2: Diagram 3.2 Video & Audio settings Enable settings for video stream, snapshot, OSD, Record and Audio. 1）CBR setting: Set CBR enabled or disabled, default value is Disable. Note: CBR is fixed ratio. 18
Resumen del contenido incluido en la página 20
IP99 series 2）Resolution: Set record resolution D1: 720x480 (NTSC) / 720x576 (PAL) Half D1: 720x240 (NTSC) / 720x288 (PAL) CIF: 352x240 (NTSC) / 352x288 (PAL) QCIF: 176x120 (NTSC) / 176x144 (PAL) 3）Limit frame rate to: Set frame rate according o resolution. 4）OSD setting: Set OSD text and font size. 5）Record: Set REC File path, REC file Duration Time and REC Disk Overwrite at. “REC Disk Overwrite at” means that when HDD remaining storage is less than the value you set, IP99 will del
