Resumen del contenido incluido en la página 1
MODEL G0605X/G0606X
EXTREME SERIES
12" TABLE SAW
OWNER'S MANUAL
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
Resumen del contenido incluido en la página 2
Resumen del contenido incluido en la página 3
Table of Contents INTRODUCTION ............................................................................................................................... 3 SECTION 1: SAFETY ....................................................................................................................... 7 SECTION 2: CIRCUIT REQUIREMENTS ...................................................................................... 12 S
Resumen del contenido incluido en la página 4
SECTION 4: OPERATIONS ........................................................................................................... 29 SECTION 5: ACCESSORIES .........................................................................................................43 SECTION 6: MAINTENANCE......................................................................................................... 45 SECTION 7:
Resumen del contenido incluido en la página 5
INTRODUCTION Foreword Contact Info www.grizzly.com
Resumen del contenido incluido en la página 6
Resumen del contenido incluido en la página 7
Resumen del contenido incluido en la página 8
Identification Figure 1. A. J. B. K. C. L. D. M. E. N. F. O. G. P. H. I. Q.
Resumen del contenido incluido en la página 9
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Indicat
Resumen del contenido incluido en la página 10
Safety Instructions for Machinery 7. NEVER OPERATE MACHINERY WHEN 17. REMOVE ADJUSTING KEYS AND TIRED OR UNDER THE INFLUENCE OF WRENCHES. DRUGS OR ALCOHOL. ON 8. ONLY ALLOW TRAINED AND PROP- 18. CHECK FOR DAMAGED PARTS ERLY SUPERVISED PERSONNEL TO BEFORE USING MACHINERY. OPERATE MACHINERY. 9. KEEP CHILDREN AND VISITORS AWAY. 19. USE RECOMMENDED ACCESSORIES. 10. MAKE WORKSHOP CHILDPROOF. 20. DO NOT FOR
Resumen del contenido incluido en la página 11
Safety Instructions for Table Saws 1. SAFETY GUARDS. 8. CROSSCUTTING OPERATIONS. The blade cuts completely through the top of the workpiece on through-sawing operations. 9. CUT-OFF PIECES. 2. KICKBACK. 10. BLADE HEIGHT. Until you have a clear under- standing of kickback and how it occurs, DO 11. WORKPIECE SUPPORT. NOT operate this table saw! 3. REACHING OVER SAW BLADE. 12. DAMAGED SAW BLADES. hands or a
Resumen del contenido incluido en la página 12
Statistics show that most common acci- dents among table saw users can be linked to kickback. Kickback is typically defined as the high-speed expulsion of stock from the table saw toward its opera- tor. In addition to the danger of the opera- tor or others in the area being struck by the flying stock, it is often the case that the operator’s hands are pulled into the blade during the kickback. Protecting Yourself From Kickback Preventing Ki
Resumen del contenido incluido en la página 13
Glossary of Terms VERY Arbor: Non-Through Cut: Bevel Edge Cut: Blade Guard: Perpendicular: Crosscut: Push Stick: Dado Blade: Rabbet: Dado Cut: Riving Knife or Splitter: Featherboard: Kerf: Straightedge: Through Cut: Kickback: Rip Cut: Parallel:
Resumen del contenido incluido en la página 14
SECTION 2: CIRCUIT REQUIREMENTS Power Connection Device Operation Figure 2 Serious personal injury could occur if you connect the machine to power before com- pleting the setup process. DO NOT connect the machine to the power until instructed later in this manual. Electrocution or fire could result if machine is not grounded and installed in compliance with electrical codes. Compliance MUST be verified by a qualified electrician! Full Load Amperage Draw Draw
Resumen del contenido incluido en la página 15
Extension Cords (220V Only) 440V Conversion Page 60 58 Phase Converter Precaution L3 Page 59
Resumen del contenido incluido en la página 16
SECTION 3: SET UP Set Up Safety Items Needed for Set Up This machine presents serious injury hazards to untrained users. Read through this entire manu- Description Qty al to become familiar with the controls and opera- tions before starting the machine! Wear safety glasses dur- ing the entire set up pro- cess! The Model G0605X/ Unpacking G0606X is a heavy machine. DO NOT over- exert yourself while unpacking or mo
Resumen del contenido incluido en la página 17
Hardware and Tools (Not Shown): Qty Machine Inventory Box Contents (Figures 3 & 4) Qty A. B. C. D. Fence Inventory E. F. G. Box Contents (Figure 5) Qty H. A. I. B. J. K. Figure 5. Fence Rail Inventory Figure 3. Box Contents (Figure 6) Qty A. B. C. Figure 4. Figure 6.
Resumen del contenido incluido en la página 18
Extension Table Outfeed Table Inventory Inventory Box Contents (Figure 8) Qty Box Contents (Figure 7) Qty A. A. B. B. C. C. D. D. E. E. Hardware and Tools (Not Shown): Qty Hardware and Tools (Not Shown): Qty
Resumen del contenido incluido en la página 19
Hardware Recognition Chart
Resumen del contenido incluido en la página 20
Clean Up Site Considerations Floor Load Machine Data Sheet For opti- mum performance from your machine, make sure you clean all moving parts or sliding Placement Location contact surfaces that are coated. Figure 9 Gasoline and petroleum products have low flash points and could cause an explosion or fire if used to clean machinery.
