Resumen del contenido incluido en la página 1
MODEL G8993
4" TILE SAW
OWNER'S MANUAL
COPYRIGHT © JULY, 2007 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#LO9296 PRINTED IN CHINA
Resumen del contenido incluido en la página 2
����������������������������������������������������������������������� �������������������������������������������������������������� ���������������������������������������������������������������������� �������������������������������������������������������������������� ������������������������ ������������������������������������������������������������������ �������������������������������������������������������������������� ���������������������������������������������������������������
Resumen del contenido incluido en la página 3
SECTION 1: SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazard- ous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention meas
Resumen del contenido incluido en la página 4
7. ONLY ALLOW TRAINED AND 17. REMOVE ADJUSTING KEYS PROPERLY SUPERVISED PER- AND WRENCHES. Make a habit SONNEL TO OPERATE MACHIN- of checking for keys and adjusting ERY. Make sure operation instruc- wrenches before turning machinery tions are safe and clearly under- on. stood. 18. CHECK FOR DAMAGED PARTS 8. KEEP CHILDREN AND VISITORS BEFORE USING MACHINERY. AWAY. Keep all children and visi- Check for binding and alignment tors a safe distance from the work of parts, broken parts, part m
Resumen del contenido incluido en la página 5
Additional Safety Instructions for Tile Saws 8. INSPECT THE TOOL REGULARLY. 1. KEEP HANDS DRY NEAR Perform machine inspections and ELECTRICITY. Do not touch elec- maintenance service promptly as trical connections with wet hands. required. 2. ALL PLUG AND RECEPTACLES 9. ATTEND TO YOUR MACHINE. MUST BE OFF THE GROUND Never walk away and leave the AND IN A DRY LOCATION. machine running. 3. KEEP BLADE WELL 10. KEEP BLADES IN GOOD LUBRICATED. Ensure that the CONDITION. Replace or sharpen
Resumen del contenido incluido en la página 6
SECTION 2: INTRODUCTION Foreword Contact Info We are proud to offer the Grizzly Model If you have any comments regarding this G8993 4" Tile Saw. This model is part of a manual, please contact us: growing Grizzly family of fine power tools. When used according to the guidelines set Grizzly Industrial, Inc. forth in this manual, you can expect years C/O Technical Documentation Manager of trouble-free, enjoyable operation and P.O. Box 2069 proof of Grizzly’s commitment to customer Bellingham, WA
Resumen del contenido incluido en la página 7
SECTION 3: SET UP Unpacking Inventory Your new item was carefully packaged for Model G8993 Inventory (Figure 1) safe shipping. If you discover any damage A. Tile Saw ............................................. 1 after you have signed for delivery, immedi- B. Vinyl Hose .......................................... 1 ately call Customer Service at (570) 546- C. Rubber Connector .............................. 1 9663 for advice. D. End Wrench (10mm, 19mm) .............. 1 E. Box Wrench (10mm) .
Resumen del contenido incluido en la página 8
Assembly 1. Install appropriate blade (not included) using the box wrench and end wrench provided (Figure 2). The blade arbor retaining bolt has a reverse thread. Figure 4. Attach the vinyl hose. 4. When connecting the tile saw to a threaded faucet or hose, use the sup- plied rubber connector. When using a water tank, the tank should be located 1 at least 31 ⁄2" higher than the work area (Figure 5). Figure 2. Attach the cutting blade. 2. Attach the water valve to the saw using the mach
Resumen del contenido incluido en la página 9
SECTION 4: OPERATIONS Operation If the diamond wheel stops or makes 1. Put on safety goggles, hearing protec- an abnormal noise while operating, tion, and an approved respirator. promptly switch the saw OFF. 2. Set the saw base on the material to be cut. Use the side of the base to align the diamond wheel with the layout line. Shortened blade life and personal inju- ry may result if the diamond wheel 3. Make sure the diamond wheel is kept is not used properly. Do not use the off the mate
Resumen del contenido incluido en la página 10
SECTION 6: MAINTENANCE 5. Be sure that the arrows on the blade point in a clockwise direction, matching the arrow on the blade guard. ! 6. Securely fasten arbor retaining bolt. Motor Brushes 1. DISCONNECT THE SAW FROM Always DISCONNECT POWER before POWER! servicing, adjusting, or doing main- tenance to reduce the risk of acci- 2. To replace worn motor brushes, remove dental injury or electrocution. the brush caps, located on either side of the motor housing, with a screw- driver (Figure 8)
Resumen del contenido incluido en la página 11
Parts Breakdown ��� ��� ��� �� �� �� �� ���� ���� �� ����� �� ��� ��� ����� �� �� � � � �� �� � �� � �� �� � � �� � � �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� �� ���� �� ���� �� �� Model G8993 4" Tile Saw -9-
Resumen del contenido incluido en la página 12
Parts List REF PART # DESCRIPTION 1 PHTEK38M TAP SCREW M4 X 60 2 P8993002 BRUSH TERMINAL 3 P8993003 STATOR ASSEMBLY 4 P8993004 TERMINAL 5 P8993005 SEAL PACKING 6 P8993006 BEARING WASHER 7 P608 BALL BEARING 608ZZ 8 P8993008 RUBBER COVER 9 P8993009 HANDLE COVER ASSEMBLY 10 P8993010 SWITCH RUBBER COVER 11 P8993011 SWITCH 12 P8993012 CONNECTOR 13 P8993013 HOUSING ASSEMBLY 14 P8993014 NAME PLATE 15 PHTEK31M TAP SCREW M4 X 14 16 PSS31M SET SCREW M5-.8 X 8 17 PS61M PHLP HD SCR M5-.8 X 30 17-1 PLW01M LO
Resumen del contenido incluido en la página 13
REF PART # DESCRIPTION 38 P8993038 WOODRUFF KEY 39 P8993039 ARMATURE 40 PS06M PHLP HD SCR M5-.8 X 20 40-1 PLW01M LOCK WASHER 5MM 40-2 PW02M FLAT WASHER 5MM 41 P8993041 FLANGE BOLT M8-1.25 X 15 LH 42 P8993042 OUTSIDE BLADE FLANGE 43 PRP63M ROLL PIN 6 X 34 44 P8993044 BASE 45 P8993045 SLEEVE 46 PLW03M LOCK WASHER 6MM 47 P8993047 WING BOLT 501 P8993501 WATER PLUG 501-1 PS02M PHLP HD SCR M4-.7 X 12 501-2 PW05M FLAT WASHER 4MM 502 P8993502 VINYL HOSE 503 P8993503 ROBBER CONNECTOR 504 P8993504 T-WRE
Resumen del contenido incluido en la página 14
WARRANTY Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of mainte- nance. This is Grizzly’s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any particular purpose, are hereby limited to the durati
Resumen del contenido incluido en la página 15
WARRANTY CARD Name _________________________________________________________________ Street _________________________________________________________________ City _______________________ State _________________________ Zip _________ Phone # ____________________ Email ________________________ Invoice # _____ Model # ____________________ Order # _______________________ Serial # ______ The following information is given on a voluntary basis. It will be used for marketing purposes to help us develo
Resumen del contenido incluido en la página 16
Send a Grizzly Catalog to a friend: Name________________________________ Street________________________________ City______________State______Zip_______ FOLD ALONG DOTTED LINE Place Stamp Here GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE
