Resumen del contenido incluido en la página 1
INSTALLATION/OPERATION MANUAL
SATELLITE SYSTEM
MODEL LP-1000
Made in U.S.A.
U.S. Patent Pending
Winegard Company • 3000 Kirkwood St. • Burlington, IA 52601-2000 • 319/754-0600 • FAX 319/754-0787 • www.winegard.com
Printed in U.S.A. © Winegard Company 2004, 2005 2452040 Rev. 12/19/05
1
Resumen del contenido incluido en la página 2
Congratulations! You have selected one of the most advanced and lowest profile satellite antennas available today. The Winegard RoadTrip™ LP antenna is a technologically advanced satellite tracking system. The RoadTrip LP is designed for use ® ® with DIRECTV and DISH Network satellite television providers. This manual provides important information on the installation and operation of your RoadTrip LP antenna. Please take time to read the manual before installing or operating your antenna. Icon
Resumen del contenido incluido en la página 3
1. Introduction ........................................................................................................................... 4 1.1 System Overview ............................................................................................................ 4 1.2 Parts Provided with RoadTrip LP .................................................................................. 4 1.3 Additional Equipment and Materials Required for Operation of RoadTrip LP ............ 4 2. Safety....
Resumen del contenido incluido en la página 4
1. INTRODUCTION 1.1 System Overview The Winegard RoadTrip LP is a low profile, in-motion satellite system. RoadTrip LP utilizes GPS (global positioning system) and DVB (digital video broadcasting) technology. GPS is used to determine the present location of your antenna, and DVB is used to verify the antenna has located the correct satellite. Roadtrip is a Ku-band satellite television reception antenna that is gyro stabilized and has a continuous 360° rotation to keep it locked on the selected
Resumen del contenido incluido en la página 5
Fig 1.1 Rotate Base 40.00” PCB Main Control Assembly Electronics Sub-base 28.625” 33.500” EL Motor LNBF 28.625” Azimuth Motor Pill Box GPS Cable Clamp 33.250” Knee Reflector Reflector Foot Back Reflector Base 2.2 Operational Safety: Failure of the vehicle driver RoadTrip LP is capable of advanced on-road television satellite to pay complete attention to the op- tracking. Satellite tracking systems are designed for reception of eration of the vehicle could cause an television programming while t
Resumen del contenido incluido en la página 6
3. INSTALLATION 3.1 Installation Overview: 1. Gather the tools and materials required for installation 2. Unpack and inspect RoadTrip LP Plan your entire installation 3. Select a location to mount the antenna. . before you start. Determine the 4. Mount the antenna system location of all of your equip- 5. Adjust the antenna switch settings ment and make sure cable and 6. Route and connect coax and wires. wires are long enough to reach their termination point
Resumen del contenido incluido en la página 7
If the height of the obstruction on the roof is 6 inches, the Fig 3.2 antenna should be mounted no closer than 18 inches from the obstruction. If the obstruction is higher than 6 inches, you should add an additional 10 inches in distance for every additional 3 inches in height. UNIT BASE Obstruction Height Clearance distance 6"……………………………………….18" 9"……………………………………….28" 12"……………………………………….38"
Resumen del contenido incluido en la página 8
3.5 Mounting the Antenna Hardware Kit: 1. Cable ties ..............................................................2 2. Rocker switch .......................................................1 1. 3. Surface mount box screw, #6 x 1/2 ......................2 11. 10. 4. Wallplate, surface mount screw #6-32x1, white..2 5. Surface mount screw, #6 x 3/4, white ..................2 6. RG-6 connector O-ring/gel ..................................2 7. Small red flag connector ................................
Resumen del contenido incluido en la página 9
3.6 Adjusting the Antenna Switch Settings Depending on the satellite receiver and the mounting option Antenna switches may selected, it may be necessary to remove the antenna radome need to be adjusted prior to and adjust the switch setting. The antenna switch comes preset at the operating the system. factory for mounting Option A (see Section 3.4 Fig 3.3) and for use with DirecTV receivers (see Fig 3.5). If you have selected mounting Option B, or if you are using a DISH network receiver, remo
Resumen del contenido incluido en la página 10
3.7 Route and connect the coax and wires Determine the best location for the RG-6 coax and 16 gauge power wires to enter the vehicle, and the location of the satellite receiver and rocker switch. Drill ½“ hole in the roof for the coax and power wires to enter the vehicle. Insert the ends of the 35’ section of RG-6 and 35’ section of 16 gauge power wire into the hole. Be sure to insert the ends that do not have connectors on them. Push coax and power wires into the vehicle. Using a 7/16" wrench,
Resumen del contenido incluido en la página 11
Pull remaining cable and wire into the vehicle. Place the cable entry plate over the hole and cables. Screw in place and seal plate and screws with the approved sealant. Depending on the length of the coax and wiring on the roof, it may be necessary to secure them with cable clamps. Clamping the cable every 12" to 16" should eliminate any unecessary cable movement. Trim coax cable if necessary and strip RG-6 coax in- side the vehicle, illustration at right. Attach the provided F-connector to end
Resumen del contenido incluido en la página 12
4. OPERATION 4.1 Initial Satellite Receiver Setup It is very important to set up the satellite receiver for proper Refer to Appendix B for satellite antenna operation. Receiver hardware and software varies, receiver setups for initial and multidish depending on manufacturer. If you have a new receiver or operation. Follow the instructions for you have removed your satellite receiver from the vehicle, your satellite television provider. it may be necessary to repeat the satellite receiver setup
Resumen del contenido incluido en la página 13
After the unit has acquired GPS, it will lower the reflector to the proper elevation for a satellite search in your location. As the unit scans the proper elevation, it will locate satellite signals. The antenna GPS acquisition will nor- will return to a scanned satellite location and verify the satellite’s mally take less than a minute. If you DVB identification. If it is the correct satellite, the antenna will peak have traveled a long distance with- on the signal and stop. If it is not the co
Resumen del contenido incluido en la página 14
Appendix A Satellite Coverage Maps and Receiver Compatability A.1 DISH NETWORK The RoadTrip LP will operate with most standard DISH Network receivers. The antenna will continually track satellite 119 and will function while stationary with satellites 119 and 110. The RoadTrip LP will not operate with DISH Network HDTV receivers or with any DISH Network satellites other than 119. Winegard does not recommend using receivers with hard drives not recommended by the manufactuer for mobile applicat
Resumen del contenido incluido en la página 15
A.2 DIRECTV RoadTrip LP will operate with most standard DIRECTV receivers. The antenna will continually track satellite 101 and will function while stationary with satellites 101 and 119. RoadTrip LP will not operate with DIRECTV HDTV receivers or on any other DIRECTV satellites other than 101 and 119. Winegard does not recommend using satellite receivers with hard drives not recommended by the manu- facturer for mobile applications. RoadTrip will not operate in all areas satellites 101 and 11
Resumen del contenido incluido en la página 16
Appendix B Setup and Operation of Satellite Receivers B.1 DISH Network (To activate your DISH Network receiver, call 1-888-ADD-DISH). Using your DISH Network Point Dish/Signal Screen There are several applications where it is necessary and helpful to use the DISH Network Point Dish/Signal Screen. See Fig B.1.1. The following instructions will help you acquire this screen on most DISH Network receivers. You will use this screen to determine if you are locked on the correct satellite, and fo
Resumen del contenido incluido en la página 17
Using your DISH Network Receiver for Multidish Operation To set your receiver to automatically switch from satellite 119 to satellite 110 in stationary mode, use the following instructions: In stationary position, be sure you have a clear view of satellites 119 and 110. Go to “Point Dish/Signal” screen and select the 119 satellite. Turn on the RoadTrip antenna to begin search for the desired satellite. Wait for RoadTrip to search and acquire satellite 119, end the conical search and enter “Sleep
Resumen del contenido incluido en la página 18
B.2 DIRECTV (To activate your DIRECTV receiver, call 1-888-238-7177) There are many manufacturers of DIRECTV Receivers. These instructions are for use with common menus found in most DIRECTV Receivers. If they differ from your receiver, follow instructions provided with your receiver. Set up your DIRECTV Receiver Dish Select “Menu” on the remote control to access Main Menu. Select ‘7’ for “Dish Pointing” and press OK. Use arrow buttons and highlight “Select Dish” and press “OK”. Specify the o
Resumen del contenido incluido en la página 19
Appendix C. Maintenance and Troubleshooting Maintenance It is advisable to perform monthly maintenance on your antenna. Clean off bugs and dirt on the outside of radome using mild soap and water; treat radome with ProtectAll*. Check fasteners on radome, antenna and antenna mounting brackets and tighten if necessary. Be sure cables and wiring are properly connected and secured. Annual maintenance — remove radome from antenna and clean off dirt and debris from antenna base using a clean rag. Do n
Resumen del contenido incluido en la página 20
Appendix D. Specifications and Warranty Specifications Frequency Band........................... 12.2 to 12.7 GHz Height ....................................................................6” Elevation Scan Range Weight............................................................. 62 lbs ......17 degrees to 63 degrees relative to the horizon Shipping Weight ............................................. 78 lbs Azimuth Scan .......................................... Continous Supply Voltage......
