Resumen del contenido incluido en la página 1
iMcV-PSE-MidSpan
Operation Manual
Resumen del contenido incluido en la página 2
FCC Radio Frequency Interference Statement This equipment has been tested and found to comply with the limits for a Class B computing device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful inte
Resumen del contenido incluido en la página 3
Table of Contents FCC Radio Frequency Interference Statement ........................................................ii Warranty................................................................................................................ii About the iMcV-PSE-MidSpan................................................................................1 Application Diagram ..............................................................................................1 Installation ...............
Resumen del contenido incluido en la página 4
About the iMcV-PSE-MidSpan The iMcV-PSE-MidSpan is an SNMP-manageable, IEEE 802.3af Power over Ethernet (PoE) Injector, used to supply current to a PoE-compliant PD (Powered Device). This makes it the perfect solution when installing compliant PDs such as IP cameras, VoIP phones and other end devices (i.e. the IE-MiniMc media converter) where there is no power source in close proximity. The iMcV-PSE-MidSpan installs between a switch/hub and the device requiring power, providing detecti
Resumen del contenido incluido en la página 5
Installation The iMcV-PSE-MidSpan may be installed into the iMediaChassis series, the IE- MediaChassis or MediaChassis series. Each module will occupy one-slot in the chassis. NOTE Due to power limitations in iMediaCenter series chassis, the installation of a PSE-MidSpan into an iMediaCenter chassis is highly discouraged and will void the PSE-MidSpan’s warranty. It is not recommended that the iMcV-PSE-MidSpan module be installed in an IE-MediaChassis- 1/DC (850-33100). The power
Resumen del contenido incluido en la página 6
DIP Switch Settings Feature Switch Function Default PoE ENA S1 Enables PoE functionality ON Zero Current ENA S2 0 current LED will glow red if OFF no device is connected to the PSE-MidSpan or the PD device is not valid Classification ENA S3 Determines what amount of OFF power the PD device is drawing (4W, 7W or 15W) Auto Restart S4 Device will automatically OFF discover PD device should a power failure occur S5-S8 are OFF; Factory default, do not change 3
Resumen del contenido incluido en la página 7
LED Indicators The iMcV-PSE-MidSpan features device-specific and several diagnostic LEDs. The LED functions are as follows: PWR FAIL Glows red when an overcurrent or internal fault is detected within the PSE-MidSpan PoE circuit. OVER CUR Glows red when an overcurrent condition lasts for more than 60 ms after power up and/or glows red when an over temperature condition occurs. Glows green when power is being supplied to PWR the PSE-MidSpan. Glows red when there is no device c
Resumen del contenido incluido en la página 8
Configuring the iMcV-PSE-MidSpan with iView² The PSE-MidSpan, when installed in a managed chassis, is configurable through iView² software. To configure the PSE-MidSpan, open the iView2 software and select the chassis in which the PSE-MidSpan has been installed. When Auto Discovery detects the chassis and identifies the PSE-MidSpan, select it to configure or monitor the modules. Software settings always override hardware settings, so DIP Switch settings should be set to match the confi
Resumen del contenido incluido en la página 9
Specifications Physical Specifications Dimensions: 4.19” x .78” x 2.75” (106.4mm x 19.81mm x 69.85mm) Environmental Operating Temperature: 32° - 122° F (0° - 50° C) Storage Temperature: 0° - 160° F (-20° - 70° C) Humidity: 5 - 95% (non-condensing) Power Power Input (Maximum): 3.2A@5VDC Power Output: 0.3A @ 48 VDC IMC Networks Technical Support Tel: (949) 465-3000 or (800) 624-1070 (in the U.S. and Canada); +32-16-550880 (Europe) Fax: (949) 465-3020
Resumen del contenido incluido en la página 10
4. After removal, always place the boards on a grounded, static-free surface, ESD pad or in a proper ESD bag. Do not slide the modules or stand alone units over any surface. WARNING! Integrated circuits and fiber optic components are extremely susceptible to electrostatic discharge damage. Do not handle these components directly unless you are a qualified service technician and use tools and techniques that conform to accepted industry practices. 7
Resumen del contenido incluido en la página 11
Safety Certifications CE: The products described herein comply with the Council Directive on Electromagnetic Compatibility (2006/108/EC). For further details, contact IMC Networks. European Directive 2002/96/EC (WEEE) requires that any equipment that bears this symbol on product or packaging must not be disposed of with unsorted municipal waste. This symbol indicates that the equipment should be disposed of separately from regular household waste. It is the consume
Resumen del contenido incluido en la página 12
19772 Pauling Foothill Ranch, CA 92610-2611 USA TEL: (949) 465-3000 FAX: (949) 465-3020 www.imcnetworks.com © 2009 IMC Networks. All rights reserved. The information in this document is subject to change without notice. IMC Networks assumes no responsibility for any errors that may appear in this document. iMcV-PSE-MidSpan is a trademark of IMC Networks. Other brands or product names may be trademarks and are the property of their respective companies. Document Numbe
