Resumen del contenido incluido en la página 1
INSTALLATION INSTRUCTIONS FOR PART 99-7603
APPLICATIONS
Nissan Versa
2007-2011
99-7603
KIT FEATURES
• DIN Mount Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
• Double DIN Mount Radio Provision
• Stacked ISO Mount Units Provision
KIT COMPONENTS
A) Radio Housing • B) ISO Brackets • C) Trim Plate • D) Double DIN Trim Plate
Harness & Antenna Connections (sold separately)
• 70--7552 - Nissan Harness 07-up
B
A
• 40-NI12 - Nissan Adapter 07-up
D
C
TOOLS REQUIRED:
Small
Resumen del contenido incluido en la página 2
99-7603 TABLE OF CONTENTS Dash Disassembly - Nissan Versa 2007-2011 . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,2 Kit Assembly - DIN Mount Radio Provision with Pocket . . . . . . . . . . . . . . . . . . . . . . . . 3 - ISO Mount Radio Provision with Pocket. . . . . . . . . . . . . . . . . . . . . . . . 4 - Double DIN Mount Radio Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - Stacked ISO Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Resumen del contenido incluido en la página 3
99-7603 DASH DISASSEMBLY NISSAN VERSA 2007-2011 A 1 Disconnect the negative battery ter- minal to prevent an accidental short circuit. 2 Unclip and remove the panel above the radio. (Figure A,B) 3 Remove (2) Phillips screws securing the radio trim panel then unclip and remove the entire panel surrounding the radio and a/c controls. (Figure C) B C 1
Resumen del contenido incluido en la página 4
99-7603 DASH DISASSEMBLY NISSAN VERSA 2007-2011 D 4 Remove (4) Phillips screws securing PRESET A-B-C CD RADIO LOAD radio, unplug and remove radio. DISP CLOCK (Figure D) 6CD CHANGER SCRL RPT 1 4 RDM SEEK TUNE AUDIO PUSH TRACK 2 5 AUX PWR FF-REW FILE FOLDER SCAN 3 VOL 6 5 Remove (4) Phillips screws securing CAT CH each bracket to factory radio. (Retain these brackets to be re-used during double DIN or stacked ISO kit assem- bly.) (Figure E) Continue to kit assembly. E 2
Resumen del contenido incluido en la página 5
99-7603 KIT ASSEMBLY DIN MOUNT RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A Note: You will need to remove the aftermarket radio’s trim ring if equipped. 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward. (Figure A) 2 Slide the aftermarket radio into the cage until it snaps into place. (Figure B) 3 Attach the trim plate supplied with the B kit to the front of the radio housing assembly. (Figure B) Conti
Resumen del contenido incluido en la página 6
99-7603 KIT ASSEMBLY ISO MOUNT RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. Note: The following modification A will need to be made to both ISO brackets when using the ISO mount radio provision. Cut or trim the area shown from the ISO bracket. (Figure A) 1 Mount the ISO Brackets to the after- market radio using the screws sup- plied with the radio. (Figure B) 2 Slide the radio into the radio housing until it snaps into place. (Figure C) FRONT 3 Att
Resumen del contenido incluido en la página 7
99-7603 KIT ASSEMBLY DOUBLE DIN MOUNT RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the factory brackets (removed from factory radio during disassembly) to the sides of the double DIN radio using screws supplied with the double DIN radio. (Figure A) 2 Place the double DIN trim plate on the front of the double DIN radio. (Figure B) Continue to final assembly. B 5
Resumen del contenido incluido en la página 8
99-7603 KIT ASSEMBLY STACKED ISO UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. A 1 Mount the factory brackets (removed from factory radio during disassembly) to the sides of the stacked ISO units using screws supplied with the ISO units. (Figure A) 2 Place the double DIN trim plate on the front of the stacked ISO units. (Figure B) Continue to final assembly. B 6
Resumen del contenido incluido en la página 9
99-7603 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disas
Resumen del contenido incluido en la página 10
99-7603 I NOTES 8
Resumen del contenido incluido en la página 11
99-7603 NOTES 9
Resumen del contenido incluido en la página 12
...... ----------------- .... ---------------- 99-7603 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 10/06/10 © COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION INST99-7603
