Resumen del contenido incluido en la página 1
OWNER’S MANUAL
DATA PROJECTOR
TDP-S20 (SVGA)
TDP-S21 (SVGA / With Document Camera)
Others Maintenance Operations Preparations Before Using
Resumen del contenido incluido en la página 2
Before Using SAFETY PRECAUTIONS The lightning flash with arrowhead symbol, within an equilateral triangle, is intended - Reorient or relocate the receiving antenna. to alert the user to the presence of uninsulated "dangerous voltage" within the product's - Increase the separation between the equipment and receiver. enclosure that may be of sufficient magnitude to constitute a risk of electric shock to - Connect the equipment into an outlet on a circuit different from that to which the receiver i
Resumen del contenido incluido en la página 3
IMPORTANT SAFETY INSTRUCTIONS CAUTION:PLEASE READ AND OBSERVE ALL WARNINGS AND 5. Heat 8. Power-Cord Protection INSTRUCTIONS GIVEN IN THIS OWNER'S MANUAL AND THOSE The product should be situated Power-supply cords should be MARKED ON THE UNIT. RETAIN THIS BOOKLET FOR FUTURE away from heat sources such as routed so that they are not likely to REFERENCE. radiators, heat registers, stoves, or be walked on or pinched by items This set has been designed and manufactured to assure personal safety. I
Resumen del contenido incluido en la página 4
IMPORTANT SAFETY INSTRUCTIONS (Continued) e) If the product has been dropped or 10. Lightning storms 12. Do not place the product 15. Accessories damaged in any way. For added protection for this vertically Do not place this product on an f) When the product exhibits a product during storm, or when it is unstable cart, stand, tripod, Do not use the product in the distinct change in performance - left unattended and unused for bracket, or table. The product may upright position to project the t
Resumen del contenido incluido en la página 5
IMPORTANT SAFETY INSTRUCTIONS (Continued) POWER SUPPLY CORD SELECTION If your line voltage is 220 to 240V, use one of the following types of cable. 19. Replacement Parts 22. Do not get your hands When replacement parts are between the camera arm Plug Plug required, be sure the service and the main unit when configuration Plug type Line voltage configuration Plug type Line voltage technician has used replacement setting the camera arm Australian 200 – 240V parts specified by the EURO 220 – 240V
Resumen del contenido incluido en la página 6
IMPORTANT PRECAUTIONS (Continued) OTHER CAUTIONS AND INFORMATIONS Avoid Volatile Liquid Copyrights Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or Showing or transmitting commercial imaging software or broadcast or cable-broad plastic products touching the unit for a long time. They will leave marks on the finish. casting programs with the purpose of other than the personal and private viewing, If cleaning with a chemically saturated cloth, be sure
Resumen del contenido incluido en la página 7
CONTENTS Before Using Others SAFETY PRECAUTIONS .................................................................................. 2 Trouble indications ............................................................................................. 41 IMPORTANT SAFETY INSTRUCTIONS ........................................................... 4 Before calling service personnel ........................................................................ 42 POWER SUPPLY CORD SELECTION .....................
Resumen del contenido incluido en la página 8
Preparations Checking the package contents Names of each part on the main unit Please make sure that the following items are included in the box, along with the main unit. If any item is missing, please contact the store immediately where you purchased the product. (5) (6) (4) (3) (2) (1) (1) (4) (7) (5) (2) (6) (8) (3) (7) (8) (9) (9) (10) (11) (12) Back Front ■ ■ (1) Remote control ■ ■ (2) R6 (SIZE AA) batteries for remote control (2) ■ ■ (3) CD-ROM Name : Function ■ ■ (4) Owner’s Manual (1)
Resumen del contenido incluido en la página 9
Names of each part on the control panel and remote control Parts on the rear panel Control panel Remote Control (1) (6) (5) (4) (3) (2) Remote control transmitter CONTROL S-VIDEO MONITOR AUDIO OUT R L VIDEO COMPUTER 2 IN COMPUTER 1 IN (Y/PB/PR ) AUDIO IN (Y/PB/PR ) (9) (10) (11) (4) (3) TEMP LAMP FAN (6) (2) (1) (8) (12) (13) (2) (1) (3) (7) (8) (7) (15) (14) (13) (12) (11) (10) (9) (8) Name : Main Function (4) (7) (6) (5) p.19 (1) Infrared remote sensor : Senses commands from the remote contro
Resumen del contenido incluido en la página 10
Approx. 5m Approx. 5m Names of each part on the document camera (TDP-S21) Preparing and using the remote control ■ Loading dry-cell batteries ■ Operating the remote (1) into the remote control control q Remove the battery cover. Point the remote control toward the (2) (10) projector’s infrared remote sensor, (3) and press a button on the remote (6) (7) (4) control. • Operating the projector from the front (8) (12) w Insert the dry-cell batteries. (5) (9) (11) Be sure to align the plus and minus
Resumen del contenido incluido en la página 11
Placement Connection Placement Styles Before connection As shown in the figures below, this device can be placed in 4 different styles. • Read the owner’s manual of the device you are connecting to the projector. The factory setting is “floor-mounted front projection.” Set the Projection mode in the • Some types of computer cannot be used or connected to this projector. p.32 default setting menu , in accordance with your needs. p.45 Check for an RGB output terminal, supported signal , etc. •Turn
Resumen del contenido incluido en la página 12
Operations Turning the power on and off Notes ■ Connecting the power cord • The start-up screen will disappear after a moment. You can dismiss the start-up screen Insert the power cord connector into the 1 before this by performing any operation. You can also configure the start-up screen not to AC IN socket of the projector. p.31 appear via the Display setting menu . • The first time you use the projector after purchase, after the start-up screen disappears, Insert the power cord plug into a wa
Resumen del contenido incluido en la página 13
Basic operations 5 Turn on the power. Projector placement angle adjustments 1 p.22 Turn on the power by following the instructions in “Turning on the power” . The placement angle and the height of the projected image can be adjusted by the foot adjuster. 2 Select the language and the lamp power (When using the q Lift up the front of the projector to 1 first time). the desired angle, then press the foot adjuster release button. When the projector is used for the first time after purchase, menu fo
Resumen del contenido incluido en la página 14
Using handy features ● Manual adjustments and settings ■ Using auto setting Remote The menu items of the Set up menu vary depending on the input type, as shown in This function sets up the projector to the optimum state for Control panel Control the table below. each type of the input signal by using simple operations. Use the buttons to adjust the items in the table below, then press 1 Press the SET UP button. the RETURN button when you are finished. The Set up menu appears. Video 2 Press
Resumen del contenido incluido en la página 15
Using handy features (Continued) Using the menus You can call up on-screen menus, and conduct a number of adjustments and settings using ■ Cutting off the picture and sound temporarily (Mute) p.16 the operation buttons on the control panel (main unit side) and remote control. Remote When you want to project the images of another projector, overhead Control projector, etc. temporarily, this projector’s images and sound can be ■ How to use the menus turned off. The menu shown below is for operati
Resumen del contenido incluido en la página 16
Using the menu (Continued) ■ The display setting menu ■ The image adjustment menu Use this menu to adjust image-related items. Use this menu to set screen display-related items. Items that can be adjusted are marked with “Yes”, and those that cannot are marked with “No”. Description Item Video Item Description Computer Y/PB/PR Camera S-video Screen size Contrast Adjust the image contrast. Yes Yes Yes Yes (Full): Display with 800 × 600 dot resolution Lower Higher (Thru): Display with samp
Resumen del contenido incluido en la página 17
Using the menu (Continued) ■ The default setting menu ■ Displaying Information (Status display) This menu shows placement status and other settings. This displays information about the input signal, lamp use time, etc. Description Item “Yes”: displayed, “No”: not displayed p.20 Projection Sets projection mode in accordance with Placement Style. Video (Mounted (Rear mounted Item Description Computer Y/PB/PR Camera mode (Standard) (Rear) from ceiling) from ceiling) S-video Input Input source nam
Resumen del contenido incluido en la página 18
Using the document camera Please read this chapter if the model you purchased is TDP-S21 which includes a document camera. Using the camera removed from the projector ■ How to use the document camera Status before preparation 1) Disconnect the RGB 2) While pushing the lock (When stored) cable, then slide the lever in the arrow Using the camera attached on the projector lock switch to release direction, lift up the lock. document camera. Status before preparation 1) Set up arm. 2) Rotate arm. (Wh
Resumen del contenido incluido en la página 19
Using the document camera (Continued) 6 If the screen is too dark or too bright, use the CAMERA GAIN (+/–) ■ Image projection with the document camera buttons to make it easier to see. 1 Place the document. The Sharpness of the camera image can also be adjusted using Set the document at the side of the projector. p.30 the Image adjustment menu . 7 After use, fold up the document camera. p.34 Fold up the camera using the reverse order from unfolding the document camera . Notes • There is no audio
Resumen del contenido incluido en la página 20
Maintenance About lamp The product’s light source is a mercury lamp that lights at increased internal pressure. Be sure Unplug power cord. 1 to fully understand the following characteristics of the lamp and handle it with extreme care. • The lamp may explode with a loud noise due to impact or deterioration, or fail to light at Wait until lamp is sufficiently cooled. 2 the expiration of its life. Wait for at least 1 hour. •How long it takes before the lamp explodes or the life expires may vary gr
