Manual de instrucciones de Panasonic PT-LB10VU

Resumen del contenido incluido en la página 1

Resumen del contenido incluido en la página 2

Resumen del contenido incluido en la página 3

WARNING: Contents BNot for use in a computer room as defined in the Standard for the White balance R/G/B, AI, Protection of Electronic Computer/Data Processing Equipment, Preparation TV-SYSTEM, STILL MODE, ANSI/NFPA 75. IMPORTANT SAFETY NOTICE ...2 SIGNAL MODE, Projecting sRGB- BFor permanently connected equipment, a readily accessible disconnect Precautions with regard to compatible pictures device shall be incorporated in the building installation wiring; safety .............................

Resumen del contenido incluido en la página 4

BIf the power cord is used while damaged, electric shocks, short-circuits or Precautions with regard to safety fire may result. BAsk an Authorized Service Center to carry out any repairs to the power WARNING cord that might be necessary. If you notice smoke, strange smells or noise coming from the Do not handle the power cord plug with wet hands. projector, disconnect the power cord plug from the wall outlet. BFailure to observe this may result in electric shocks. BDo not continue to use the pro

Resumen del contenido incluido en la página 5

Do not look into the lens while the projector is being used. Do not short-circuit, heat or disassemble the batteries or place them BStrong light is emitted from the projector’s lens. If you look directly into this into water or fire. light, it can hurt and damage your eyes. BFailure to observe this may cause the batteries to overheat, leak, explode BBe especially careful not to let young children look into the lens. In or catch fire, and burns or other injury may result. addition, disconnect the

Resumen del contenido incluido en la página 6

Resumen del contenido incluido en la página 7

Resumen del contenido incluido en la página 8

Resumen del contenido incluido en la página 9

#RGB INPUT indicator Projector control panel Menu This indicator illuminates when a signal is being input to the RGB IN operation connector. $LAMP indicator (page 51) #$% & ' ( if a circuit abnormality is detected. * %TEMP indicator (page 50) This indicator illuminates if an abnormally high temperature is detected inside the projector or around it. If the temperature rises above a certain

Resumen del contenido incluido en la página 10

Resumen del contenido incluido en la página 11

Projector position Connections Top edge of screen Notes on connections L: Projection distance BRead the instruction manual for each peripheral device carefully before Screen SH: Image height connecting it. L SW:Image width BTurn off the power supply for all peripheral devices before making any H1: Distance from center connections. Bottom edge of screen of lens to bottom edge BIf the cables necessary for connection are not included with the peripheral of projected image device

Resumen del contenido incluido en la página 12

Resumen del contenido incluido en la página 13

Resumen del contenido incluido en la página 14

Resumen del contenido incluido en la página 15

Resumen del contenido incluido en la página 16

Resumen del contenido incluido en la página 17

Resumen del contenido incluido en la página 18

Resumen del contenido incluido en la página 19

Correcting keystone distortion Adjusting the picture Keystone distortion is corrected automatically when the projector’s automatic When an S-VIDEO/VIDEO signal is Press the F or G button on the setup function is used, but this correction will not apply if the screen itself is being input projector or remote control unit to tilted. In such cases, you can correct the keystone distortion manually with select an item, and then press the PICTURE the following procedure. I or H button to change

Resumen del contenido incluido en la página 20

CONTRAST White balance R/G/B TV-SYSTEM SIGNAL MODE This adjusts the contrast of the (S-VIDEO/VIDEO only) (RGB/YPBPR/NETWORK only) (W-BAL R/G/B) picture. (Adjust the “BRIGHT” This displays the type of signal TV-SYSTEM AUTO (RGB only) [ setting first if required before which is currently being projected. This is used to adjust the white NTSC adjusting the “CONTRAST” setting.) Refer to the list on page 60 for areas of the picture if they appear [