Resumen del contenido incluido en la página 1
1
English
Table of Contents
Usage Notice
Precautions .......................................................................................... 2
Introduction
Product Features .................................................................................. 3
Package Overview ............................................................................... 4
Product Overview ................................................................................. 5
Installation
Connecting the Projector t
Resumen del contenido incluido en la página 2
2 English Usage Notice Warning- Do not look into the lens. The bright light may hurt your eyes. Warning- To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. Warning- Please do not open or disassemble the product as this may cause electric shock. Warning- When changing the lamp, please allow unit to cool down, and follow all changing instructions. Warning- This product will detect the life of the lamp itself. Please be sure to change the lamp when it sh
Resumen del contenido incluido en la página 3
3 English Introduction Product Features This product, is an SVGA single chip 0.7”DLP Projector. The outstanding features of it are listed as follows: True SVGA, 800 x 600 addressable pixels 5 lbs (2.3 kgs) lightweight compact design Single chip DLP technology XGA compression and VGA re-sizing 120 Watts user replaceable P-VIP lamp Mac/ NEC PC-98/ FM Towns compatible NTSC/ NTSC4.43/ PAL/ PAL-N/ PAL-M/ SECAM Video compatible Full function wireless remote controller Real plug & p
Resumen del contenido incluido en la página 4
4 English Package Overview This projection display comes with all the items shown below. Check to make sure your unit is complete. Contact your dealer immediately if anything is missing. Projection Display Power Cord VGA Cable S-Video Cable Audio-In Cable for Computer Composite Video Cable Audio Cable User’s Manual Warranty Card Remote Control Carrying Case
Resumen del contenido incluido en la página 5
5 English Product Overview Panel Control Main Unit Focus Ring Remote Control Lens Receiver Speaker Carrying Handle Connection Ports Elevator Button Power Connector Elevator Foot Power Switch Security Lock Slot
Resumen del contenido incluido en la página 6
6 English Connection Ports Computer Input Connector Composite Video Audio Iuput Connector Connector S-video Audio Output Connector Connector Power Connector Power Switch Panel Control Four Directional Select Keys Menu Power / Standby Reset Temperature Source Lamp Enter
Resumen del contenido incluido en la página 7
7 English Remote Control Source Power / Standby Reset Resync Mute Freeze/CLR Picture in Picture Menu Keystone Correction Volume ( + / - ) Four Directional Select Keys Zoom In / Zoom Out Enter
Resumen del contenido incluido en la página 8
8 English Installation Connecting the Projector to Desktop Computer 1. Make sure the projector and your computer are turned off. 2. Connect one end of the projector signal cable to the projector; connect the other end to the VGA connector on the computer and tighten the screws. 3. Connect one end of the power cord into the back of projector; connect the other end to an electrical outlet. Computer Output VGA Cable Power Cord To ensure the projection display works well with your computer, please
Resumen del contenido incluido en la página 9
9 English Connecting the Projector to Portable Computer 1. Make sure the projector and your notebook are turned off. 2. Connect one end of the projector signal cable to the projector; connect the other end to the VGA connector on the notebook and tighten the screws. 3. Connect one end of the power cord into the back of projector; connect the other end to an electrical outlet. Notebook Output VGA Cable Power Cord
Resumen del contenido incluido en la página 10
10 English Connecting the Projector to Other Video Sources If your video player uses a round, one-prong composite video connector, you’ll need the video cable. If your video player uses a round, four-prong s-video connector, you’ll need the s-video cable ( See page 11 for detail information). Both cables are shipped with the projector. If you use the video cable: 1. Plug the video cable connector into the “Video out”port on your video player; plug the other end into the “Video”port on your pro
Resumen del contenido incluido en la página 11
11 English If you use the s-video cable: 1. Plug the s-video cable connector into the “S-Video”port on your video player; plug the other end into the “S-Video” port on your projector. 2. Plug the audio cable white connector into the left “Audio out” port on your video player; plug the cable’s red connector into the right “Audio out” port on the video player; plug the other end into the “Audio in” port on your projector. 3. If you need to use an external speaker (built in amplifier), plug the aud
Resumen del contenido incluido en la página 12
12 English Power On/Off the Projection Display Powering On the Projection Display 1. Remove the lens cap. 2. Ensure that the power cord and signal cable are securely connected. 3. Turn on the main power switch on the back of the projector and allow the projector to warm up for 1-2 minutes. 4. Turn on the lamp by pressing “Power/Standby” button on the Panel Control. The startup screen will display for 30 seconds and the Power/Standby indicator will light solid green. 5. Turn on your
Resumen del contenido incluido en la página 13
13 English Powering Off the Projection Display 1. Press the “Power/Standby” button to turn off the projector lamp. 2. After pressing the “Power/Standby” button, you will see a message “ Power off the lamp? ” on the on-screen display. Press the “Power/Standby” button again to confirm. Otherwise the message will disappear after 5 seconds. 3. “LAMP “ LED indicator will flash amber for about one minute. After the “LAMP” LED indicator stops flashing , you can turn off the main power switch
Resumen del contenido incluido en la página 14
14 English Adjusting the Projected Image Adjusting the Projector Height The projector is equipped with an elevator foot for adjusting the projector height. To raise the projector: 1. Press and hold the elevator button . 2. Raise the projector to the desired display angle , then release the button to lock the elevator foot into position. To lower the projector: 1. Press and hold the elevator button. 2. Lower down the projector, then release the button to lock the elevator foot into po
Resumen del contenido incluido en la página 15
15 English Adjusting the Projector Focus To focus the image, rotate the focus ring until the image is clear. The projector will focus at distances from 3.3 feet to 33 feet (1m to 10m). Focus Ring Image Size Adjustment [279”] [252”] [224”] [173”] [114”] [55”] (6.7’) (13.3’) (20.0’) (26.7’) (30.0’) (33.0’) Screen 28” 55” 84” 114” 141” 173” 196” 224” 279” 252” Diagonal Screen 22.4” 44” 67.2” 91.2” 112.8” 138.4” 156.8” 179.2” 223.2” 201.6” Width Screen 16.8” 33” 50.4” 68.4” 84.6
Resumen del contenido incluido en la página 16
16 English User Controls There are two ways for you to control the functions: Remote Control and Panel Control. Panel Control Remote Control Power / Standby Power the lamp on and off when the main power switch is turned on. Menu Press “Menu” to open the on-screen display (OSD) menus and to switch among different menus. To exit OSD, press the “Freeze/CLR” button or select the “ Exit Menu” icon and press “Enter” button. The projector saves any changes you made automatically. Source Press “Sou
Resumen del contenido incluido en la página 17
17 English Enter Press “Enter” to confirm your selection. Four Directional Select Keys Use or to select items. Use or to make adjustments for your selection. Volume To increase the volume, press To decrease the volume, press To mute the volume, press “Mute” Resync Automatically synchronizes the projector to the input source. Freeze/CLR Press the “Freeze/CLR” button to still the screen image. When the OSD is displayed, press the “Freeze/CLR” butt
Resumen del contenido incluido en la página 18
18 English OSD Menus How to operate The Projector has a multilingual On-Screen Display(OSD) menu that allows you to make image adjustments and change a variety of settings. In computer source, the OSD will be the “Computer OSD”. In video source, the OSD will be the “ Video OSD”. The projector will detect the source automatically. To open the OSD menu, press the “menu” button on the Remote Control or Panel Control. To select among different menus, press the” Menu” button again. Then use
Resumen del contenido incluido en la página 19
19 English Tint (Video mode only) The tint adjusts the red-green color balance in the projected image. Press the left key to increase the amount of green in the image. Press the right key to increase the amount of red in the image. Color (Video mode only) The color setting adjusts a video image from black and white to fully saturated color. Press the left key to decrease the amount of color in the image. Press the right key to increase the amount of color in the image. Image (Compu
Resumen del contenido incluido en la página 20
20 English Treble The treble setting controls the higher frequencies of your audio source. Press the left button to decrease the treble. Press the right button to increase the treble. Mute Choose the left icon to make the volume function ineffective. Choose the right icon to make the volume function effective. Mono / Stereo / Stereo-enhance Mono: Mono sound effect. Stereo: Stereo sound effect. Stereo-enhance: Stereo-enhance sound effect. Projection Front-Desktop The factor
