Resumen del contenido incluido en la página 1
Operating Manual
KODAK
®
CAROUSEL
Slide Projector
CONSUMER IMAGING
Resumen del contenido incluido en la página 2
Important Safety Instructions When using your projector, always follow basic safety precautions: 1. Read and understand all instructions before using this equipment. 2. Operate this projector with 110- to 125-volt 60 Hz current only. Incorrect voltage can cause projector malfunction. 3. Close supervision is necessary when any appliance is used by or near children, or others who may not understand the need for these precautions. Do not leave the projector unattended during use. 4. Be careful not
Resumen del contenido incluido en la página 3
Operating Manual KODAK CAROUSEL Slide Projector
Resumen del contenido incluido en la página 4
Resumen del contenido incluido en la página 5
Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . .Inside Front Cover Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Startup . . . . . . . . . . . . . . . . . . . . . . .
Resumen del contenido incluido en la página 6
Introduction Congratulations! You have just purchased a KODAK CAROUSEL Slide Projector which: • triples lamp life • provides brighter and more vivid colors! Introduction Take the time to read the instructions in this operating manual to become ® familiar with your KODAK CAROUSEL Slide Projector and how to operate it properly. 2 KODAK CAROUSEL® Slide Projector
Resumen del contenido incluido en la página 7
Overview FRONT RIGHT 1 – Tray 2 – Lock Ring 3 – Storage Compartment/Remote 4 – Elevating Foot 5 – Elevating Adjustment Wheel 6 – Elevating Foot Release Button 7 – Lens 8 – Viewer (Model 5600) 9 – Focus Knob 10 – Select Bar 11 – Timer (Model 5600) 12 – Reverse 13 – Forward 14 – Power/Fan/Lamp BACK RIGHT 15 – Tray Release Latch 16 – Lamp Module 17 – Reading Light 18 – Room Light Outlet (Model 5600) 19 – Remote Control Receptacle BASE 20 – Power Cord 21 – Power Cord Retainer 22 –
Resumen del contenido incluido en la página 8
Operation Operation Startup Open the storage compartment and remove the remote control. Plug the 5-pin cable remote connector into the remote-control receptacle, aligning the raised dot with the metallic rivet head. Plug the power cord into a grounded outlet with 110- to 125-volt 60 Hz current only. 4 KODAK CAROUSEL® Slide Projector
Resumen del contenido incluido en la página 9
Operation Loading the Slide Tray ® A KODAK CAROUSEL 140 Slide Tray is designed to hold up to 140 slides. Be sure that your slide mounts are in good condition; frayed or bent mounts may fail to drop into the projector. A variety of slide trays are available with capacity up to 140 slides. See your dealer in Kodak products for a complete list of Kodak trays and accessories. Note: Do not attempt to project slides mounted with sticky or loose tape. Place the tray over the center post of the projecto
Resumen del contenido incluido en la página 10
Operation Adding Your Slides Remove the lock ring by turning it counterclockwise and lifting it off. Check each slide’s orientation (horizontal or vertical), and arrange them in the order you wish to show them. Then turn the slides upside down. Number each mount in the upper right-hand corner of the film’s shiny side. Insert your first slide into the first slot in the tray so that the number is visible on the outer circumference of the tray. Insert your second slide in the second slot with the e
Resumen del contenido incluido en la página 11
Operation Replace the lock ring by turning it clockwise until it is secure Tray Place the loaded slide tray on the projector. Align the tray index bar with the gate index. The tray will drop into position. KODAK CAROUSEL® Slide Projector 7
Resumen del contenido incluido en la página 12
Operation Removing the Tray To remove the slide tray: • press the select bar all the way down • align the tray index bar with the gate index. You can then lift off the tray. 8 KODAK CAROUSEL® Slide Projector
Resumen del contenido incluido en la página 13
Operation Projecting Your Slides Lens To insert a lens, push the focus knob up and position the lens gear teeth on the lens barrel with the notch on the projector. Lamp Slide the power switch to lamp. KODAK CAROUSEL® Slide Projector 9
Resumen del contenido incluido en la página 14
Operation Forward and Press the forward button on the projector or the remote control to project the first slide. To change slides, briefly press the forward or reverse buttons. Reverse Focus Focus your first slide using the focus knob on the projector or the focus button on the remote control (Models 4400 and 5600 only). Autofocus The autofocus feature automatically focuses each slide after you focus your first slide manually. If there is a mix of slide mounts in the tray (cardboard, (Models 4400
Resumen del contenido incluido en la página 15
Operation Screen Image Use the elevating foot to horizontally center the projected image on the screen. To release the foot, press the release button, while lifting the front of the projector to the desired height. Use the elevating wheel to make fine adjustments. If the image is not level, make an adjustment by turning the leveling foot at the rear of the projector. Timer To time your slides, use the timer switch for slide changes from 3 to 22 seconds. (Models 4400 and 5600 only) To interrupt th
Resumen del contenido incluido en la página 16
Operation Reading Light To illuminate a small area for reading, lift the reading light cover while the projector lamp is on. (Model 5600 only) Room Light Outlet Plug any standard room light into the room light outlet and turn it on. It will remain on until the projector is turned to the lamp position (when a darkened (Model 5600 only) room is required). When you turn the projector off at the end of your presentation, the room light will come on again. 12 KODAK CAROUSEL® Slide Projector
Resumen del contenido incluido en la página 17
Operation Single Slides To project single slides, slide the power switch on. Remove the tray and insert a slide upside down into the projector gate. Push the slide all the way down. After viewing the slide, press forward, reverse, or the select bar to eject the slide. Selecting Slide When buying a lens, consider features such as focal length (measured in millimetres), aperture (designed as an f/stop), and the lens design (curved or Projection Lenses flat). When selecting a lens, remember that the
Resumen del contenido incluido en la página 18
Operation Choosing a Curved- The lens you select depends on how you use your projector and what type of slide mount you use. So that you may choose the lens that best meets your or Flat-Field Lens needs, we do not include a lens with the projector. To obtain the best results of a projected image, insert slides with the emulsion side toward the projection lens, slide curve toward the light source. A flat-field lens works best for: • general home projection • glass mounts • plastic mounts • mixed mo
Resumen del contenido incluido en la página 19
Operation KODAK CAROUSEL® Slide Projector 15
Resumen del contenido incluido en la página 20
Operation Editing Your Presentation Removing the To add or remove slides in the tray, you must first remove the lock ring. Turn the ring counterclockwise and lift off. Lock Ring Removing a Slide Rotate the tray to the slide you wish to remove. Firmly press and hold down the select bar to eject the slide. Adding a Slide When the lock ring is off, you can add a slide to any empty slot. (See “Adding Your Slides” on page 6.) Replace and secure the lock ring. 16 KODAK CAROUSEL® Slide Projector
