Resumen del contenido incluido en la página 1
LP840_50_60_UG.qxd 1/21/05 2:22 PM Page 1
® ® ®
LP840/LP850/LP860 INSTALLATION & INTEGRATION PROJECTOR.
USER’S GUIDE
Resumen del contenido incluido en la página 2
Declaration of Conformity Canada This Class A digital apparatus complies with Canadian ICES-003. Manufacturer: InFocus Corporation, 27700B SW Parkway Ave. Wilsonville, Oregon Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada. 97070 USA European Office: Strawinskylaan 585, 1077 XX Amsterdam, The Netherlands Agency Approvals We declare under our sole responsibility that this projector conform to the following directives and norms: UL, CUL, NOM, IRAM, GOST, C-tick E
Resumen del contenido incluido en la página 3
Table of Contents If you are experienced in setting up presentation systems, use the included Quick Set Up card. For complete details on connecting and operating the projector, refer to this User’s Guide. Electronic versions of this User’s Guide Introduction 5 in multiple languages are available on the included CD and on our website. Positioning the projector 7 The website also has technical specifications (an interactive image size cal- Connecting a computer 8 culator, laptop activation comm
Resumen del contenido incluido en la página 4
Important Operating Considerations for Safety Place the projector in a horizontal position no greater than 15 degrees off axis. 2 ft (.6m) Locate the projector in a well-ventilated area without any obstructions 2 ft (.6m) to intake or exhaust vents. Do not place the projector on a tablecloth or other soft covering that may block the vents. Locate the projector at least 4' (1.2 m) away from any heating or cooling vents. Use only InFocus-approved ceiling mounts. 2 ft (.6m) Use only
Resumen del contenido incluido en la página 5
Projector components and features: front Introduction Your new multimedia projector provides three computer, three video, and keypad two audio inputs, one audio output, and RS-232 control. The LP840 and LP850 have XGA 1024x768 resolution while the LP860 has SXGA+ heat vent 1400x1050 resolution. Optional user-changeable short, fixed short, long and super long throw lenses make this a flexible product suitable for many dif- speakers ferent uses. The projector is easy to connect, easy to use, a
Resumen del contenido incluido en la página 6
Connector Panel component video The projector provides three computer and three video connection options: VESA computer remote wired control RS232 one M1-D (DVI with USB) remote receiver monitor M1-D computer serial control (IR) RJ-45 one VESA computer one BNC (RGBHV and Pr, Pb, Y) one component RCA video (Pr, Pb, Y) lock one S-video one composite RCA video The projector provides computer and video connectors for audio support: two composite RCA stereo audio (L, R) computer o
Resumen del contenido incluido en la página 7
Positioning the projector To determine where to position the projector, consider the size and shape of your screen, the location of your power outlets, and the distance between the projector and the rest of your equipment. Here are some general guide- lines: Position the projector on a flat surface at a right angle to the screen. The projector (with the standard lens) must be at least 3 feet (0.9m) from the projection screen. Position the projector within 10 feet (3m) of your power sourc
Resumen del contenido incluido en la página 8
Connecting a computer connect computer cable Required computer connections Connect one end of the VESA computer cable to the Computer 2 connector on the projector. Connect the other end to the video port on your computer. If you are using a desktop computer, you first need to disconnect the moni- tor cable from the computer’s video port. Connect the black power cable to the connector on the back of the projector connect power cable and to your electrical outlet. NOTE: Always use the power ca
Resumen del contenido incluido en la página 9
If you are using a desktop computer and want to see the image on your connect monitor cable computer screen as well as on the projection screen, plug the monitor cable to the Monitor out connector on the projector. You can also connect to your computer using a BNC cable. Connect the BNC connectors on the BNC cable to the appropriate Computer 3 connectors on connect BNC cables the projector. Connect the other end to the video port on your computer. If RG B H V you are using a desktop comput
Resumen del contenido incluido en la página 10
Displaying a computer image remove lens cap Remove the lens cap. Press the power switch on the back of the projector to the on position, then 2 press Power switch press Power button press the Power button on the top of the projector or the remote. The LED flashes green and the fans start to run. When the lamp comes on, the startup screen is displayed and the LED is steady green. It can take a minute for the image to achieve full brightness. 1 ? No startup screen? Get help on page 19. Turn
Resumen del contenido incluido en la página 11
First-time projector use with Windows 98 a The first time you connect a computer running Windows 98 to the projector, the computer recognizes the projector as “new hardware” and the Add New Hardware Wizard appears. Follow these instructions to use the Wiz- ard to load the correct driver (which was installed with your Windows operating system). If you are running Windows 2000, Windows ME, or Window XP, skip these steps and go to “Adjusting the image” on page 13. a Click Next to begin searchin
Resumen del contenido incluido en la página 12
Skip this page if you did not connect a USB mouse cable For Windows 98: If you connected the USB cable, the Add New Hardware Wizard appears again. Drivers must be installed to use the USB functionality. The Wizard launches two times. The first time it detects a USB Human Interface Device (for the key- board). The second time it detects a USB Human Interface Device (for the mouse). For Windows 2000, Windows ME, and Windows XP: The USB drivers are automatically installed. 12
Resumen del contenido incluido en la página 13
Adjusting the image release adjust height release button Adjust the height of the projector, if necessary, by pressing the release but- button tons on each side of the projector’s front to extend the elevator feet. elevator elevator foot foot Position the projector the desired distance from the screen at a 90 degree adjust distance angle (perpendicular) to the screen. See page 43 for a table listing screen sizes and distances. adjust zoom and focus Adjust the zoom or focus by pressing the po
Resumen del contenido incluido en la página 14
Connecting a video device connect A/V cable Standard video connections Plug the audio/video (A/V) cable’s yellow connector into the video-out connector on the video device. Plug the other yellow connector into the yel- low Video 3 connector on the projector. Plug a white connector into the left audio out connector on the video device and plug a red connector into the right audio out connector on the video device. Plug the remaining white connector into the left audio in connector on the pro
Resumen del contenido incluido en la página 15
You can also connect to your video device using a BNC cable. Connect the BNC connectors of the BNC cable to the appropriate Computer 3 connec- connect BNC cables tors on the projector. Connect the other end to the video port on your video device. Use the A/V cable’s audio connectors as described on the previous RG B H V page (the yellow connectors on the A/V cable are not used). When 4 BNCs are connected, the projector handles a composite synch on H. When 3 BNCs are connected, the projector
Resumen del contenido incluido en la página 16
Displaying a video image remove lens cap Remove the lens cap. Press the power switch on the back of the projector to the on position, then press Power switch press Power button 2 press the Power button on the top of the projector. The LED flashes green and the fans start to run. When the lamp comes on, the startup screen is displayed and the LED is steady green. It can take a minute for the image to achieve full brightness. 1 ? No startup screen? Get help on page 19. Plug in and turn on the
Resumen del contenido incluido en la página 17
Adjust the zoom or focus by pressing the power Zoom or power Focus buttons on the keypad until the desired image size and focus are produced. adjust Zoom and Focus zoom focus You can also adjust the zoom and focus via the menus. See page 32 If the image is not on the screen or viewing area, adjust it by pressing the adjust Lens Shift lens shift button on the keypad. lens shift Press the upper Lens Shift button to shift the lens upward. Press the lower Lens Shift button to shift the lens down
Resumen del contenido incluido en la página 18
Shutting down the projector Troubleshooting your setup The projector automatically blanks the screen after no active source is If your image appears correctly on the screen, skip to the next section. If it detected for 50 minutes. This blank screen helps preserve the life of the pro- does not, troubleshoot the setup. The LED on top of the projector indicates jector. The image returns when an active source is detected or a remote or the state of the projector and can help you troubleshoot. See
Resumen del contenido incluido en la página 19
startup screen A A A startup screen Source Troubleshooting Problem Solution Result Plug power cable in, press power switch, press power button. Remove lens cap. No startup screen Correct image 3 1 2 Computer image projected Only startup screen appears Press the Computer button Activate laptop’s external port or restart laptop 19
Resumen del contenido incluido en la página 20
A A Signal out of range A Adjust computer refresh rate in Control Computer image projected No computer image, just the words “Signal out of Panel>Display>Settings>Advanced> range” Adapter (location varies by operating system) You may also need to set a different resolution on your computer, as shown in the following problem, “Image fuzzy or cropped” 20
