Resumen del contenido incluido en la página 1
Instruction Manual
Prima 2e Retransfer Printer
See p.11~13,22 See p.15~19 See p.19~21
>Ink>
Jam (TurnOver)
>Cleaning
Jam (Hopper)
>Counter Reset
HR is too hot.
>Display>
Please remove
MENU
Ready
MEDIA FILM
Please,
Power Off.
See p.23~35 See p.36~40 See p.42~43
• Thank for purchasing this product.
• Please read this manual carefully before use to ensure correct operation.
It is particularly important to read the Safety Precautions for safe operation. After
re
Resumen del contenido incluido en la página 2
Declaration of Conformity Model Number: XIDi Printeryyyyy(y=A-Z,0-9 or blank) Product name: Card Printer We herewith declare that the above mentioned product complies with the following council directives and harmonized standards. Council Directives: 1999/5/EC relating to radio equipment and telecommunications terminal equipment. 89/336/EEC relating to electromagnetic compatibility. 73/23/EEC relating to electrical equipment designed for use within certain voltage limits. Harmonized Standards: E
Resumen del contenido incluido en la página 3
Information for USA NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursu- ant to part 15 the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guaran
Resumen del contenido incluido en la página 4
Contents Notes for safe operation ................................ 5 Operation ................................................................... 25 Turning on the power........................................... 25 Before use .................................................................... 7 Turning off the power ........................................... 26 Product features .................................................... 7 About the RESET button .....................................
Resumen del contenido incluido en la página 5
Notes for safe operation Before you use Read these notes on safety thoroughly before operating your printer in order to use the unit properly. Once you start using the unit, this manual should be put aside the unit, or at a convenient place where you can look up the manual any time as you need. WARNING CAUTION If you ignore the warning with this mark, and handle If you ignore the caution with this mark, and handle the unit in a wrong way, death or serious injuries may the unit in a wrong w
Resumen del contenido incluido en la página 6
Notes for safe operation (continued) Ground the machine with the attached electric cord Do not use the machine while it has a fault. • Do not use the machine while it has a fault, as this may when connecting it to the utility outlet. cause a fire or electric shock. • Using a cord other than the one supplied for grounding may • Immediately turn off the power, pull out the power plug, and cause an electric shock when the machine fails. ask your dealer to repair. Do not try to repair it by your
Resumen del contenido incluido en la página 7
Before use Product features Handling of transfer film, ink ribbons and cards • This card printer allows printing of high-quality, full- color images equivalent to photographic quality onto Handling standard size (ISO 7810 compliance) plastic cards using sublimation type transfer printing. Take note of the following points when handling print • Use of sublimation type retransfer printing enables media (retransfer film and ink ribbons) and cards. printing of cards other than those made of PVC and
Resumen del contenido incluido en la página 8
Before use (continued) Storing and handling cards after printing Escape Clause Avoid storing the cards in locations exposed to direct We do not provide compensation for any malfunction sunlight or with high temperature and high humidity. during card printing caused by breakdown of the Furthermore, avoid contact with the following chemicals machine, ink ribbon defects or card characteristics. and stationery, as they can cause discoloration or fading of the cards: In addition, we also do not prov
Resumen del contenido incluido en la página 9
Before use (continued) Installation Installation diagram The performance of the card printer is strongly influenced by the installation location.Be careful of the Ventilation holes are provided for the cooling fan on the following items as for installation location. bottom and sides of the unit. Avoid inserting any object • Install in the locations is not so much as to cause print into the gap between the bottom of the unit and the top defect due to dust adherence. of the stand. Install the unit
Resumen del contenido incluido en la página 10
Names of parts Front When the printer door is open Control panel Slide knob Printer door Card tray Retransfer film cassette Power switch Ink ribbon cassette (Accessory) (Accessory) Rear External connection Power input jack terminals External connection terminals USB cable connection terminals 10
Resumen del contenido incluido en la página 11
Set-up Connecting the IC unit (sold separately) Large and compact size IC units are sold separately, as 3. Connect the printer and IC unit. are specialized optional devices for the printer. Consult your dealer for more details. Connect the cable which comes with the IC unit to the OPTION 1 terminal. WARNING • Make sure that the power switch is turned OFF and the AC cable is detatched from the plug, before connecting and disconnecting the IC units. Otherwise Electric electric shocks, fires or mal
Resumen del contenido incluido en la página 12
Set-up (continued) Compact IC unit (sold separately) CAUTION Please ask your dealer for the Compact IC unit Be careful not to pinch your finger when installing. connection. Connect the compact IC unit to the host computer with 2. install the laminator the interface cables which are commercially available. Laminator(ILU) Compact IC unit Interface cable (Commercial item) Memo If the mounting is uneven, the card would not be transported smoothly. be sure to fit the units right Connecting the Lamina
Resumen del contenido incluido en la página 13
Set-up (continued) Connecting the power cord 1. Check the plug. • For AC 120V type • For AC220-240V type (North America) (Europe) * The detached power cords vary according to model and country of purchase. 2. Plug the power cable into the printer. Plug the power cable of the laminator if it is installed. CAUTION Always use a grounded power outlet. Never share the outlet with other electrical equipment. Use an AVR (Automatic Voltage Regulator) if there is a possibility of voltag
Resumen del contenido incluido en la página 14
Set-up (continued) Discharging the card Installing the card stacker When correctly printed, the cards are discharged from Hang the stacker claw on the stacker receptacle. the left side. If a card jam or a write error on magnetic stripes occurs on the way, results differ depending on the areas. Portion A: If a card jam , a write error on magnetic stripes or an IC unit encord error occurs on the way, press the RESET button, then the ENTER button. The printer is initialized, and the cards are dis
Resumen del contenido incluido en la página 15
Set-up (continued) Setting the ink ribbon 3. Insert the ink ribbon into the cassette. CAUTION Do not touch the surface of the ink Stretch the ink ribbon along three shafts with the ink ribbon with your hands. face of the ribbon facing outside and insert the bobbins firmly into the bobbin holders. 1. Activate the slide knob and open the printer door. Feed spool (yellow bobbin) When the slide knob is moved, the printer door opens downwards. Hold the door with your hand and open it Shaft slowly. W
Resumen del contenido incluido en la página 16
Set-up (continued) 6. Close the printer door. 4. Wind the ribbon, taking up the slack. If you want to mount the retransfer film, keep the door Turn the knob in the arrow direction to wind a small open and go to the next page. portion of the ink ribbon. If the ink ribbon does not wind up, go back to step 3, and insert the ink ribbon firmly into the bobbin holders. Memo CAUTION If the ink ribbon is not tightly wound, When the ink ribbon is wound up to the end, the slack may cause the ribbon to be
Resumen del contenido incluido en la página 17
Set-up (continued) Setting the retransfer film 3. Insert the retransfer film into the cassette. CAUTION Do not touch the retransfer film Stretch the retransfer film along three shafts with the surface with your hands. retransfer face of the film facing outside and insert the bobbins into the bobbin holders firmly. At this time, perform setting so that the film is inside the 1. Activate the slide knob and open the printer door. guide. Wind the film to the wind spool more than three stripes (two f
Resumen del contenido incluido en la página 18
Set-up (continued) 6. Setting the number of frames to be used. 4. Wind the retransfer film to take up the slack. The number of frames of the retransfer film being used Turn the knob in the arrow direction to wind a small is set. portion of the retransfer film. If the film does not wind For details, refer to the “Media Type” setting on page up, go back to step 3, and insert the bobbins firmly into 32. the bobbin holders. This work must be done when the used film (number of frames) is changed. CA
Resumen del contenido incluido en la página 19
Set-up (continued) Caution when loading the retransfer film Setting cards cassette and/or the ink ribbon cassette Please use cards specified by your dealer. This unit can take both 0.76 mm(0.03inches)-thick and 0.25 mm The following caution shall be kept when the retransfer (0.01inches)-thick cards. The factory setting is for 0.76 film cassette and/or the ink ribbon cassette is removed mm-thickness. because of card jam or other trouble. Please pay enough attention so that the retransfer film CAU
Resumen del contenido incluido en la página 20
Set-up (continued) 2. Pull the card bracket back. 4. Close the card tray. The card bracket locks when it reaches the hole. Push the card tray back into the printer until it no longer moves. 3. Insert the cards and move the bracket back into position. Limit the number of cards as the card bracket moves back slightly from the lock position. CAUTION Setting the cards improperly can cause feed jams. Check that the cards are neatly arranged. CAUTION To print pre-printed cards on this printer, determi
