Resumen del contenido incluido en la página 1
FormsPro 4000se Series
FormsMaster 8000se Series
PrintMaster 850 Series
Programmer’s Manual
©Printek, Inc. 2003
1517 Townline Road
Benton Harbor, MI 49022
269-925-3200
Printek Part Number 5640
Resumen del contenido incluido en la página 2
IBM and Proprinter are registered trademarks of International Business Machines Corporation, DEC is a registered trademark of Digital Equipment Corporation, Epson is a registered trademark of Seiko Epson, Code V is a trademark of QMS, Inc., QMS is a registered trademark of QMS, Inc.Printek is a registered trademark of Printek, Inc. Specifications subject to change without notice. ii
Resumen del contenido incluido en la página 3
TABLE OF CONTENTS INTRODUCTION 1 How to Use This Manual 1 Printer Model Descriptions and Key Features 2 Selecting Emulations 2 Changing Forms/Tractor Paths 3 ANSI X3.64 EMULATION 5 Introduction 5 Control Codes and Escape Sequences Grouped by Function 7 Communications 7 Character Size and Line Spacing 8 Character Attributes 9 Horizontal Position 9 Vertical Position 10 Horizontal and Vertical Position 12 Form Length and Form Feed 12 Horizontal Tabs 13 Vertical Tabs 14 Printer
Resumen del contenido incluido en la página 4
Form Length and Form Feed 53 Horizontal Tabs 55 Vertical Tabs 55 Horizontal and Vertical Tabs 56 Horizontal Margins 56 Vertical Margins 57 Graphics 58 Printer Controls 59 Emulations 60 Control Codes and Escape Sequences Sorted Alphabetically 62 DEC LA120/210 EMULATION 65 Introduction 65 Control Codes and Escape Sequences Grouped by Function 67 Communications 67 Character Size 68 Character Attributes 69 Character Sets 69 Line Pitch 70 Horizontal Position 71 Vertical Position
Resumen del contenido incluido en la página 5
Horizontal Margins 101 Vertical Margins 102 Graphics 102 Printer Controls 104 Forms and Tractors 106 Emulations 107 Control Codes and Escape Sequences Sorted Alphabetically 108 GENICOM 3840 AND 3410 ANSI EMULATION 109 Introduction 109 Control Codes and Escape Sequences Grouped by Function 111 Communications 111 Character Size 111 Character Set 112 Horizintal Position 113 Vertical Position 115 Horiztonal Tab 116 Vertical Tab 117 Forms Setup 118 Graphics 119 Printer Control 1
Resumen del contenido incluido en la página 6
Resumen del contenido incluido en la página 7
INTRODUCTION This manual describes the software interfaces supported by the FormsPro 4000se, FormsMaster 8000se and PrintMaster 850 series printers. It is written for a programmer who will be developing software for the printer, and contains information not normally needed by a printer operator/user. Basic information on printer operation (setting the printer up, loading paper, replacing ribbons, etc.) can be found in either of the FormsPro4000se, FormsMaster 8000se or PrintMaster 850 Se
Resumen del contenido incluido en la página 8
Introduction Printer Model Descriptions and Key Features The Printek FormsPro 4000se, FormsMaster 8000se and PrintMaster 850 series printers are high speed, heavy duty serial dot matrix printers designed especially for printing upon hard to print forms. Such forms are often not printed adequately by other printers. The printer is also designed to be factory floor rugged while still quiet enough for the office. All models provide straight paper paths for jam free paper motion and a zero
Resumen del contenido incluido en la página 9
Introduction Changing Forms/Tractor Paths As mentioned above, Printek FormsPro 4000se, FormsMaster 8000se and PrintMaster 850 series printers have ten complete sets of forms parameters. These different parameters, or forms, may be selected either from the front panel or with escape sequences. In the FormsPro 4503se and FormsMaster 8003se series printers, selecting a different form may also select a different tractor path. The tractor path is one of the parameters which may be set for
Resumen del contenido incluido en la página 10
Resumen del contenido incluido en la página 11
ANSI X3.64 EMULATION Introduction This section describes the control codes and escape sequences comprising ANSI X3.64 emulation. This emulation may be selected by setting “Emulation” to “ANSI X3.64” in the appropriate interface setup menu, or via software with the ESC ESC 1 sequence. While this emulation is selected, control codes and escape sequences from other emulations are not available. Control codes and escape sequences are used to control printer operation. An ASCII control cod
Resumen del contenido incluido en la página 12
ANSI X3.64 Emulation This should clarify any ambiguity. The examples may also be helpful when analyzing a hex dump (see Hex Dump chapter) printed by the printer. Some escape sequences refer to the active column or active line. The active column is the column where the next character will be printed. Printing a character or a space will increment the active column. The active line is the line where the next character will be printed. A line feed will increment the active line. Column a
Resumen del contenido incluido en la página 13
ANSI X3.64 Emulation Control Codes and Escape Sequences Grouped by Function Communications End of Text ETX If “ETX/ACK” is set to “On” in the serial interface setup menu, then receipt of an ETX causes the printer to transmit an ACK to the host computer. Since the ETX may be a legal value within an escape sequence, it is the user's responsibility to ensure that an ETX used for data handshake is not sent within an escape sequence. The user must also ensure that the maximum block size or
Resumen del contenido incluido en la página 14
ANSI X3.64 Emulation Character Size and Line Spacing Set Character and Line Spacing ESC [ n1 ; n2 SP G Sets the character and line spacing in decipoints (1/720 of an inch). The first parameter, n1, sets the line spacing. The second parameter, n2, sets the character spacing. Typical values for n1 and supported values for n2 are shown below. Other values for n2 will be ignored. To change only the horizontal or only the vertical spacing, omit the other value from the sequence or set it t
Resumen del contenido incluido en la página 15
ANSI X3.64 Emulation Character Attributes Select Graphic Rendition ESC [ n m Selects the graphic rendition n from the following table. n Rendition 0 Normal 1 Emphasized 3 Italic 4 Underline For italic mode to work correctly, an Epson FX font must be selected (check the “Font” value in the forms setup menu). The other available fonts do not include italic characters. Example: The following escape sequence will select emphasized mode. Escape Sequence: ESC [ 1 m Hexadecima
Resumen del contenido incluido en la página 16
ANSI X3.64 Emulation Absolute Horizontal Tab ESC [ n ` Sets the current print position to column n. The actual position will depend on the current character spacing. If n is less than the left margin, the active column will be set to the left margin. If n is greater than the right margin, then a line feed will be performed and the active column will be set to the left margin. Example: The following escape sequence will set the active column to column 65. Escape Sequence: ESC [ 6 5 ` H
Resumen del contenido incluido en la página 17
ANSI X3.64 Emulation Partial Line Down PLD (or) ESC K Performs a half line feed. Causes the current line to be printed, and then advances the paper one half line at the current line spacing. If “Auto CR” is set to “On” in the interface setup menu, a carriage return will also be performed. Control code: PLD Hexadecimal: 8B Escape Sequence: ESC K Hexadecimal: 1B 4B Partial Line Up PLU (or) ESC L Performs a reverse half line feed. Causes the current line to be printed, and then retra
Resumen del contenido incluido en la página 18
ANSI X3.64 Emulation Horizontal and Vertical Position New Line NEL (or) ESC E Causes the current line to be printed, and then sets the current print position to the left margin and performs a line feed. Equivalent to a carriage return (CR) line feed (LF) combination. Control code: NEL Hexadecimal: 85 Escape Sequence: ESC E Hexadecimal: 1B 45 Form Length and Form Feed Form length is the distance from the top of the form to the bottom of the form. A form feed will advance the paper
Resumen del contenido incluido en la página 19
ANSI X3.64 Emulation Horizontal Tabs Horizontal tab stops are associated with columns, not absolute physical positions. Changing character spacing will change the physical position of the tab stops. Default tab stops are set at every eighth column, i.e. column 9, 17, 25, 33, 41, etc. If different tab stops are to be set, the default tab stops should first be cleared. Horizontal Tab HT Advances to the next horizontal tab stop. If no tab stop exists between the active column and the rig
Resumen del contenido incluido en la página 20
ANSI X3.64 Emulation Escape Sequence: ESC [ 3 g Hexadecimal: 1B 5B 33 67 Vertical Tabs Vertical tab stops are associated with lines, not absolute physical positions. Changing line spacing will change the physical position of the tab stops. Vertical Tab VT Causes the current line to be printed, and then advances the paper to the next vertical tab stop. If no vertical tab stops are set, then a line feed is done instead. If “Auto CR” is set to “On” in the interface setup menu, a carriag
