Resumen del contenido incluido en la página 1
Removing the optional finisher 1
Printing
To remove the optional finisher, its bins, and its stand, complete the following sections.
Paper handling Preparing for disassembly
1 Turn the power off.
2 Remove all print media from the bins.
Maintenance
Removing the bins
Troubleshooting
1 Grasp the top bin (bin 1) and tilt it up.
Administration
Index
www.lexmark.com
Lexmark W820
Resumen del contenido incluido en la página 2
Removing the optional finisher 2 Printing 2 Pull the bin straight out Paper handling Maintenance Troubleshooting Administration Index www.lexmark.com Lexmark W820
Resumen del contenido incluido en la página 3
Removing the optional finisher 3 Printing 3 Loosen the two screws under the bottom bin (bin 2). Paper handling Maintenance Troubleshooting Administration Index 4 Lift the bin and pull it straight out. 5 Set the bins aside. www.lexmark.com Lexmark W820
Resumen del contenido incluido en la página 4
Removing the optional finisher 4 Printing Disconnecting the finisher from the printer 1 Push the finisher release latch. Paper handling Maintenance Finisher release latch Troubleshooting Administration 2 Push the finisher away from the printer. Index Note: The finisher slides to the right while still on its stand. www.lexmark.com Lexmark W820
Resumen del contenido incluido en la página 5
Removing the optional finisher 5 Printing 3 Locate the cable connecting the transport unit to the finisher. Paper handling Maintenance Troubleshooting Administration Index 4 Loosen the two thumbscrews on each side of the connector. 5 Disconnect the plug from the finisher. www.lexmark.com Lexmark W820
Resumen del contenido incluido en la página 6
Removing the optional finisher 6 Printing 6 Locate the finisher power cable on the printer. 7 Press down on the tab on the cable plug, and then pull the plug out. Paper handling Maintenance Troubleshooting Administration Index www.lexmark.com Lexmark W820
Resumen del contenido incluido en la página 7
Removing the optional finisher 7 Printing 8 Locate the other end of this cable in the lower of the three connectors. 9 Pull the plug straight out. Paper handling Maintenance Troubleshooting Administration Index www.lexmark.com Lexmark W820
Resumen del contenido incluido en la página 8
Removing the optional finisher 8 Printing 10 Disconnect the finisher cable from the back of the printer Paper handling Maintenance Troubleshooting Administration Index www.lexmark.com Lexmark W820
Resumen del contenido incluido en la página 9
Removing the optional finisher 9 Printing 11 Locate the other end of this cable in the middle connector on the back of the finisher. Paper handling Maintenance Troubleshooting Administration Index 12 Loosen the thumbscrews on each side of the plug, and pull the plug straight out. www.lexmark.com Lexmark W820
Resumen del contenido incluido en la página 10
Removing the optional finisher 10 Printing Removing the finisher from the stand CAUTION! This procedure should be completed by two people to avoid injury. Ask Paper handling someone to help you move the finisher. 1 Hold down the left side of the black lever on the bottom rear of the stand. Maintenance Troubleshooting Administration Index www.lexmark.com Lexmark W820
Resumen del contenido incluido en la página 11
Removing the optional finisher 11 Printing 2 Have someone push the finisher away from the printer until it slides off the stand. Paper handling Maintenance Troubleshooting Administration Index www.lexmark.com Lexmark W820
Resumen del contenido incluido en la página 12
Removing the optional finisher 12 Printing Removing the divertor cover 1 Pull the two tabs on the divertor cover straight out using a flat blade screwdriver or a Paper handling flat key. Maintenance Troubleshooting Administration Index www.lexmark.com Lexmark W820
Resumen del contenido incluido en la página 13
Removing the optional finisher 13 Printing 2 Rotate the divertor cover up and over toward the standard bin to release it. Paper handling Maintenance Troubleshooting Administration Index www.lexmark.com Lexmark W820
Resumen del contenido incluido en la página 14
Removing the optional finisher 14 Printing Removing the transport unit 1 While supporting the transport unit, swing the two vertical support levers up. They Paper handling snap into place in the bottom of the transport unit. Maintenance Troubleshooting Administration Index www.lexmark.com Lexmark W820
Resumen del contenido incluido en la página 15
Removing the optional finisher 15 Printing 2 Gently lower the transport unit into its vertical position. Paper handling Maintenance Troubleshooting Administration Index www.lexmark.com Lexmark W820
Resumen del contenido incluido en la página 16
Removing the optional finisher 16 Printing 3 Grasp the transport unit on each side, and then lift it straight up and off the finisher. Paper handling Maintenance Troubleshooting Administration Index www.lexmark.com Lexmark W820
Resumen del contenido incluido en la página 17
Removing the optional finisher 17 Printing Disassembling the stand The finisher stand consists of two metal pieces. The guide rail holding plate is attached Paper handling directly to the printer. The guide rail is attached to guide rail holding plate. 1 Loosen the two screws on the guide rail. 2 Pull the guide rail away from the guide rail holding plate and set it aside. Maintenance Guide rail Troubleshooting holding plate Administration Guide rail Index www.lexmark.com Lexmark W820
Resumen del contenido incluido en la página 18
Removing the optional finisher 18 Printing 3 Loosen the two screws on the guide rail holding plate. 4 Pull the guide rail holding plate off, and set it aside. Paper handling Maintenance Troubleshooting Administration Index www.lexmark.com Lexmark W820
Resumen del contenido incluido en la página 19
Removing the optional finisher 19 Printing Removing the finisher plate 1 Loosen the screws on the finisher plate attached to the right side of the printer. Paper handling 2 Pull the finisher plate straight off. Maintenance Troubleshooting Administration Index www.lexmark.com Lexmark W820
Resumen del contenido incluido en la página 20
Removing the optional finisher 20 Printing 3 Reattach the stacking arm. See Reinstalling the stacking arm for more information. 4 Turn the printer on. Paper handling Maintenance Troubleshooting Administration Index www.lexmark.com Lexmark W820