Resumen del contenido incluido en la página 1
Cordless Screwdriver
MODEL 6710D
MODEL 6710DW
With Fast Charger
INSTRUCTION MANUAL
I
SPECIFICATIONS
Model 67100
weight
speed length
Wood screws Machine screws Nuts
6 mm 6 mm 220 195 mm 1 1 kg
5 1 mm x 50 mm
11.4' x2'l f 114") (1/4") Rimin 17-518") 12.4 lhsl
Battery Cartridge 7000 Model OC7100 Fast charger
Dimensions Net
iL x W x H) 1 weight
A.C only DC 145 mm x 80 mm x 61 mm 0 7 kg
72V 1 Hr
50 Hr 60 Hr 72V (5 314" x 3 1/8" x 2 318") I1 5 lhsl
Resumen del contenido incluido en la página 2
IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. KEEP WORK AREA CLEAN. Cluttered areas and benches invite injuries. 2. CONSIDER WORK AREA ENVIRONMENT. Don't use power tools in damp or wet locations. Keep work area well lit. Don't expose power tools to rain. Don't use tool in presence
Resumen del contenido incluido en la página 3
14. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turn- ing it on. 15. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. 16. OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. 17. STAY ALERT. Watch what you are doing, use common sense. Don't oper- ate tool when you a
Resumen del contenido incluido en la página 4
IMPORTANT SAFETY INSTRUCTIONS I. SAVE THESE INSTRUCTIONS - This manual contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. 3. CAUTION - To reduce risk of injury, charge only MAKITA Battery 7000. Other types of .batteries may burst causing personal injury and damage. 4. Do not expose charger to rain or snow. 5. Use of an a
Resumen del contenido incluido en la página 5
ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (SOOF) or ABOVE 4OoC (104OF). 2. Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. 3. Do not allow anything to cover or clog the charger vents. 4. Always cover the battery terminals with the battery cover when the battery cartridge is not used. 5. A battery short can cause a large current flow, overheating, possible burns and e
Resumen del contenido incluido en la página 6
Installing or removing battery cartridge 0 Always switch off the tool before insertion or removal of the battery cartridge. 0 To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the barrel. .To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Snap the set plate back into place. Be sure to close the set plate fully before using th
Resumen del contenido incluido en la página 7
Switch action I 0 Set the reversing switch lever just in front of the trigger switch to Forward (FWD) Reversing switch lever I or Reverse (REV). Then pull the trigger to turn the tool ON and release it to turn it OFF. To change the direction of bit rotation, release the trigger, let the tool come to a complete stop, and then slide the switch lever to the opposite side. The trigger switch does not work if the switch lever is in the neutral position. Trigger switch I CAUTIONS: 0 Be
Resumen del contenido incluido en la página 8
Fastening torque adjustment I 0 The fastening torque may be adjusted by Fastening torque adjustment ring turning the adjustment ring to align the Bit notched line on the ring with a number on the indicator label. However, the clearance between the ring and the cap is 2.5 mm (1/8") maximum after one full turn, and the ring should not be forced beyond this point. 0 Turning the adjustment ring in the arrow direction obtains a higher torque (HI side); turning in the opposite direction
Resumen del contenido incluido en la página 9
Hole 0The hole on the heel of the tool is a con- venient way to carry it by a cord, hook or other means. Drill chuck (Accessory) 0 To install a drill chuck, remove the insert bit by a strong jerk, then a drill chuck can be replaced with the insert bit by a sharp push of the hand. .To install the drill bit, place it in the chuck as far as it will go. Tighten the chuck collar by hand. Place the chuck key in each of three holes, and tighten clockwise. 0 To remove the drill bit, place
Resumen del contenido incluido en la página 10
Screwdriving Item I Rominal Diameter (mm) Match your bit to your screw. Bit No. Wood Screw Phillips bits Select your screws on and the nominal right. dia- )- 2.1 - 2.7 13/32'' - 118") meter with the chart No. 2 3.1 - 4.8 (1/8" - 3/16') No.3 1 5.1 (3/16") Slotted bits Select a slotted bit to match the slot on the screw heads. If the bit is too small for the screw slot, the bit and/or screw head may be damaged.
Resumen del contenido incluido en la página 11
MAINTENANCE CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance and adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 11
Resumen del contenido incluido en la página 12
ACC ESSO R I ES CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. - 0 Charger 12V for cer Bits Model DC 71 12 Size Part No. Part No. 113109-0 Phillips #3 784215-0A Slotted 0 Battery cartridge 7000 Part No. 632002-4 Square drill bit 784606-0A I
Resumen del contenido incluido en la página 13
0 Battery holster Carrying case Plastic case Holster holds Steel case extra battery. Part No. 181428-2 part N~, 823087-3 Part No. 823033-3C 13
Resumen del contenido incluido en la página 14
Aug -09-'84 US CORDLESS SCREWDRIVER Model 67100 Note: The switch and other part configurations may differ from country to country. 14
Resumen del contenido incluido en la página 15
MODEL 67101D Aug -0944 US ’EM $&, DESCRIPTION ‘i\M & DESCRIPTION MACHINE MACHINE ~ 1 1 Torque Adlust Ring 20 16 1 F Washer 8 1 17 1 Ball Bearing 60BLLB 2 Cap 3 1 0 Ring 16 18 I Retaining Ring S-6 1 19 1 Housing Set 1WNh Item 361 4 Guide Plate 5 1 Lock Washer 14 20 1 Battery 7000 6 1 F Washer 14 21 1 Switch Motor 7 1 Leal sprang 22 1 6 1 Sled Ball 3 5 23 2 Plane Bearing 3 3 1 Spindle 24 1 Gear 9-04 10 1 P,n 4 25 Name Plate 1 11 I Compression Spring 14 26 7 P H Screw M4x22 IWiIh
Resumen del contenido incluido en la página 16
MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita’s Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or mater
