Manual de instrucciones de Powerware X-Slot USB Module

Resumen del contenido incluido en la página 1

X-SlotZ USB Module
User’s Guide
www.powerware.com

Resumen del contenido incluido en la página 2

Powerware is a registered trademark and X-Slot is a trademark of Powerware Corporation. Microsoft and Windows are registered trademarks of Microsoft Corporation. . Copyright 2000 Powerware Corporation, Raleigh, NC, USA. All rights reserved. No part of this document may be reproduced in any way without the express written approval of Powerware Corporation.

Resumen del contenido incluido en la página 3

TABLE OF CONTENTS Installation ..................................................... 3 Inspecting the Equipment ........................................................ 3 Preparation ................................................................. 3 Installing the USB Module ....................................................... 4 Installing the Software ....................................................... 5 Service and Support ........................................................... 6 T

Resumen del contenido incluido en la página 4

Table of Contents X-Slot Z USB Module User’s Guide : 05146515 A Uncontrolled Copy 4

Resumen del contenido incluido en la página 5

INSTALLATION The Universal Serial Bus Module (USB module) is an X-SlotZ connectivity device that allows your UPS to communicate with a USB-compliant computer using LanSafe III power management software. The following requirements must be met to install the USB module: : A computer with a USB port : LanSafe III (v4.15 or higher) power management software 9 : Microsoft Windows 98 or 2000 9 : A Powerware UPS with an X-Slot such as the 9125 Inspecting the Equipment If any equipment has been damaged

Resumen del contenido incluido en la página 6

Installing the USB Module Installing the USB Module To install the USB module, perform the following steps: 1. Remove the X-Slot cover (or existing X-Slot module) on the UPS rear panel. Retain the screws (see Figure 1). NOTE UPSs with a single X-Slot may have another X-Slot module already installed (such as the Powerware 9125 UPS). If there is a communication cable attached to this module, disconnect the cable and then remove the X-Slot module. Figure 1. Removing the Single-Port Module 2. To pre

Resumen del contenido incluido en la página 7

Installing the USB Module Installing the Software After the USB module installation is complete, perform the following steps to install the USB module drivers and software: 1. Insert the LanSafe III software CD into the CD-ROM drive. 2. Click Next when the “Add New Hardware Wizard” opens. 3. Select “Search for the best driver for your device” and click Next. 4. Select “Specify at location” and click Browse. 5. Navigate to one of the following CD directories: CD Directory Operating System \LanSaf

Resumen del contenido incluido en la página 8

Service and Support Service and Support If you have any questions or problems with the USB module, call your Local Distributor or the Help Desk at one of the following telephone numbers and ask for a USB module technical representative. In the United States --- 18003654892 In Canada --- 46191668001 All other countries --- 91987013149 Please have the following information ready when you call the Help Desk: : Model number : Date of failure or problem : Symptoms of failure or problem : Customer ret

Resumen del contenido incluido en la página 9

Two-YearLimitedWarranty(USandCanadaOnly) Two-Year Limited Warranty (US and Canada Only) 9 Powerware Corporation warrants the electronics of the USB module to be free from defects in material and workmanship for a period of two years from Date of Purchase. If, in Powerware Corporation’s opinion, the electronics fails to meet its published specifications due to a defect in material and workmanship covered by this warranty, Powerware Corporation will repair or replace the warranted Unit at no cost

Resumen del contenido incluido en la página 10

International Limited Warranty Powerware Corporation will not be responsible or liable for work done or expense incurred in connection with repair or replacement except as expressly authorized by Powerware Corporation, Raleigh, NC, USA in writing. If a service engineer is required, labor, at current published rates, and all travel and living expenses are for the account of the user. Powerware Corporation does not warrant equipment not manufactured by Powerware Corporation including any battery n