Manual de instrucciones de Hans Grohe ShowerArc 26396001

Resumen del contenido incluido en la página 1

Installation Instructions / Warranty
ShowerArc
26396001

Resumen del contenido incluido en la página 2

ShowerArc 26396001 Minimum ceiling height – 90 1/2” 2

Resumen del contenido incluido en la página 3

Installation Considerations • For best results, Hansgrohe recommends on the left and the cold supply must enter that this unit be installed by a licensed, the valve on the right. If the valve is cross- professional plumber. connected, it cannot function correctly. • Please read over these instructions thor- • The difference in water pressure between oughly before beginning installation. the hot and cold supplies should not Make sure that you have all tools and sup- exceed 10 psi or the the

Resumen del contenido incluido en la página 4

Installation in 90º corner: Instructions begin on page 5 Wall-to-wall installation Requires 26397000 installation kit (included): Instructions begin on page 13. Roughing-in The ShowerArc requires 1/2” NPT female fittings, recessed 3/8” behind the surface of the finished wall, for the hot and cold water supplies for the thermostatic mixing valve. 4

Resumen del contenido incluido en la página 5

Installation in 90º corner Only one set of supplies is required – do not install two sets of supplies. The thermostatic mixing valve may be installed on either wall. This diagram shows both possible positions for the installation. 5

Resumen del contenido incluido en la página 6

Installation in 90º Corner Seal the wall around the supplies with waterproof sealant. Failure to seal the wall can lead to possible water damage. 1 2 3 4 6

Resumen del contenido incluido en la página 7

5 6 7 8 Seal the wall around the anchors with waterproof sealant. Failure to seal the wall can lead to possible water damage. 7

Resumen del contenido incluido en la página 8

9 10 Seal the wall around the anchors with waterproof sealant. Failure to seal the wall can lead to possible water damage. 11 Be careful not to drill into water lines! 12 6 mm 8

Resumen del contenido incluido en la página 9

13 14 15 16 9

Resumen del contenido incluido en la página 10

17 18 19 20 1 2 6 mm 10

Resumen del contenido incluido en la página 11

21 22 Seal the wall around the anchors with waterproof sealant. Failure to seal the wall can lead to possible water damage. 24 23 2 1 6 mm 11

Resumen del contenido incluido en la página 12

25 26 Seal the wall around the anchors with waterproof sealant. Failure to seal the wall can lead to possible water damage. Turn to page 22 to continue the installation. 12

Resumen del contenido incluido en la página 13

Wall-to-Wall Installation Only one set of supplies is required – do not install two sets of supplies. The thermostatic mixing valve may be installed on either wall. The diagram shows both possible positions for the installation. 13

Resumen del contenido incluido en la página 14

Wall-to-Wall Installation Seal the wall around the supplies with waterproof sealant. Failure to seal the wall can lead to possible water damage. 1 2 3 4 14

Resumen del contenido incluido en la página 15

5 6 7 8 Seal the wall around the anchors with waterproof sealant. Failure to seal the wall can lead to possible water damage. 15

Resumen del contenido incluido en la página 16

9 10 11 12 2 Seal the wall around the anchors with waterproof 6 mm sealant. Failure to seal the wall can lead to possible water damage. 1 Be careful not to drill into water lines! 16

Resumen del contenido incluido en la página 17

13 14 Install the 26397000 mounting set 15 16 17

Resumen del contenido incluido en la página 18

17 18 90 20 19 XX = XX 18

Resumen del contenido incluido en la página 19

21 22 1 2 6 mm 23 24 M6x8 SW 3 mm 19

Resumen del contenido incluido en la página 20

25 26 2. M6x8 1. 3. SW 3 mm M6x60 Install the 26397000 mounting set 27 28 2 Seal the wall around the an- 1 chors with waterproof sealant. 6 mm Failure to seal the wall can lead to possible water damage. 20