Resumen del contenido incluido en la página 1
User's Guide
SLWU038–August 2006
TRF2436EVM
This user’s guide provides an overview of the TRF2436 evaluation module (EVM) to
get you started using the TRF2436EVM right away. It also provides a general
description of the features and functions to be considered when using this module.
Contents
1 Introduction.......................................................................................... 1
2 TRF2436EVM Operational Procedure........................................................... 2
3 Ph
Resumen del contenido incluido en la página 2
www.ti.com TRF2436EVM Operational Procedure 1.4 Hardware Configuration The TRF2436EVM can be set up in a variety of configurations to accommodate a specific mode of operation. Before starting an evaluation, decide on the configuration and make the appropriate connections or changes. The demonstration board comes with the following factory-set configuration: Jumper J10 installed between 1-2 Jumper J11 installed between 2-3 Jumper J12 installed between 1-2 Jumper J13 installed between 1-2 Jumper J
Resumen del contenido incluido en la página 3
www.ti.com Physical Description 2.2 RX Operation 1. Set TR (J13) to logic 0. 2. Set PA_A SEL (J10) to logic 0. 3. Connect a differential LO source to the LOP/LON SMAs (or use an external balun). Set the LO to an appropriate frequency, with the power level between 0 to +4 dBm. Remember that for A-band operation, the LO input frequency is doubled inside the TRF2436; so, the LO should be set to half the frequency desired at the mixer LO port. 4. For mixer stage measurement: a. Terminate RFA (J9) an
Resumen del contenido incluido en la página 4
www.ti.com Physical Description 3.1 PCB Layout The EVM is constructed on a 4-layer, 3.6-inch × 3.6-inch, 0.042-inch thick PCB using Polycad 370 Turbo/HR material. Figure 1 through Figure 4 show the PCB layout for the EVM. Figure 1. Top Layer 1 Figure 2. Ground Plane Layer 2 4 TRF2436EVM SLWU038–August 2006 Submit Documentation Feedback
Resumen del contenido incluido en la página 5
www.ti.com Physical Description Figure 3. Power Plane Layer 3 Figure 4. Bottom Layer 4 SLWU038–August 2006 TRF2436EVM 5 Submit Documentation Feedback
Resumen del contenido incluido en la página 6
www.ti.com Physical Description 3.2 Part List Table 1 lists the parts used in constructing the EVM. Table 1. TRF2436EVM PARTS LIST QTY Ref Value Part Number Note 1 C1 470pF GRM033R71C471KD 1 C2 10pF GRM1555C1H100JZ 1 C3 5600pF C0402C562K3RACT 7 C4 C6 C11 C15 C17 C24 0.01μF GRM155R71E103KA C33 12 C5 C9 C12–C14 C16 C19 100pF GRM1555C1H101JD C20 C22 C25 C26 C31 3 C7 C8 C18 10μF ECJ-4YB1A106K 3 C10 C23 C29 1000pF GRM155R71H102KA 2 C21 C32 1.2pF 04025A1R2BAT2A 1 C28 0.1μF ECJ-0EB1A104K 2 FL1 FL2 Filt
Resumen del contenido incluido en la página 7
5 4 3 2 1 RFB SMA RFB SMA MXB SMA MXB SMA 3 J2 J2 3 J1 J1 D D TRACE GAP, NO PART TRACE GAP, NO PART TRACE GAP, NO PART TRACE GAP, NO PART FL1 FL1 R1 R1 R2 R2 MXB RFB 2 1 1 2 2 1 IN OUT Filter, 2400-2484 MHz Filter, 2400-2484 MHz DFCB22G44LBJAA_DNI DFCB22G44LBJAA_DNI DNI DNI J3 J3 50 OHM 2 1 LOP SMA LOP SMA TP1 TP1 VDD R3 R3 J4 J4 1 2 DNI DNI 50 OHM 2 1 C R4 R4 C C14 C14 1 2 100pF 100pF DNI DNI LON SMA LON SMA U1 U1 TRACE GAP, NO PART TRACE GAP, NO PART TRACE GAP, NO PART TRACE GAP, NO PART J5 J5
Resumen del contenido incluido en la página 8
5 4 3 2 1 VDD P1 P1 VDD V+PA1A RED RED FL5 FL5 C6 C6 C7 C7 +3.3V_IN +3.3V_IN 3.3V_IN 1 1 L2 L2 .01uF .01uF C5 C5 10uF 10uF 100pF 100pF D D VDD B CB 1 2 CG2 27 OHM @ 100MHz 27 OHM @ 100MHz PSG CG1 P2 P2 C8 C8 TP3 TP3 10uF 10uF BLK BLK R8 R8 2 PSG PSG PSG GND L3 L3 10K 10K 1 1 Filter Block, DC power Filter Block, DC power Murata BNX002-01 Murata BNX002-01 GND 3 V+PA2A 27 OHM @ 100MHz 27 OHM @ 100MHz VDD 1 C9 C9 Q2 Q2 1 R9 R9 C11 C11 100pF 100pF C10 C10 J10 J10 1 2 Q1 Q1 .01uF .01uF 1000pF 1000pF I
Resumen del contenido incluido en la página 9
5 4 3 2 1 VDD VDD VDD D D .01uF .01uF R12 R12 R13 R13 C33 C33 10K 10K 10K 10K R15 R15 10K 10K 1 1 J12 J12 J13 J13 2 2 1 TR ABSEL J14 J14 3 3 2 RXDGC 3 TR TR ABSEL ABSEL R16 R16 R17 R17 1K 1K 1K 1K RXDGC RXDGC R18 R18 1K 1K C C VDD VDD R20 R20 R21 R21 200 200 200 200 R22 R22 R23 R23 TP6 TP6 200 200 200 200 TP5 TP5 PABCA PABCB U2 U2 U3 U3 E1 C1 E1 C1 B1 B2 B1 B2 C2 E2 C2 E2 B B MMDT3906 MMDT3906 MMDT3906 MMDT3906 R24 R24 1K 1K R25 R25 VDD U4 U4 1K 1K MMDT3904 MMDT3904 R26 R26 750 750 R28 R28 1K 1K
Resumen del contenido incluido en la página 10
EVALUATION BOARD/KIT IMPORTANT NOTICE Texas Instruments (TI) provides the enclosed product(s) under the following conditions: This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES ONLY and is not considered by TI to be a finished end-product fit for general consumer use. Persons handling the product(s) must have electronics training and observe good engineering practice standards. As such, the goods being provided are not intended to be
Resumen del contenido incluido en la página 11
IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the t
