Manual de instrucciones de Transition Networks CGETF10XX-10X

Resumen del contenido incluido en la página 1

User’s Guide
CGETF10xx-10x
Slide-in-Module Media Converter
• Gigabit Ethernet
 Copper to Fiber
 1000Base-T to 1000Base-SX/LX
Transition Networks CGETF10xx-10x Gigabit
Ethernet media converter connects 1000Base-T
shielded or unshielded twisted-pair copper cable to
1000Base-SX or 1000Base-LX, fiber-optic cable.
The CGETF10xx-10x is also designed to be
installed in the Transition Networks PointSystem™
chassis.
Part Number Port One - Copper Port Two - Duplex Fiber-Optic
CGETF1013-105 RJ-45 1000Ba

Resumen del contenido incluido en la página 2

CGETF10xx-10x Part Number Port One - Copper Port Two - Single Fiber-Optic Installation -- Continued CGETF1029-105 RJ-45 1000Base-T SC, 1000Base-LX, 1310 TX/1550 RX 100 m (328 ft)* single mode, 20 km (12.4 miles)* Set the 4-position switch Copper Mode: up = Full Duplex  The 4-position switch is CGETF1029-106 RJ-45 1000Base-T SC, 1000Base-LX, 1550 TX/1310 RX Pause: up = Enable located on the side of the 100 m (328 ft)* single mode, 20 km (12.4 miles)* Link Pass-Through: up = Enable media con

Resumen del contenido incluido en la página 3

CGETF10xx-10x Installation -- Continued Installation -- Continued Install the slide-in-module Install the copper cable CAUTION: Slots in the PointSystem™ chassis without a slide-in-module 1. Locate or build 1000Base-T compliant copper cables with male, RJ-45 installed MUST have a protective plate covering the empty slot for Class A connectors installed at both ends. compliance. 2. Connect the RJ-45 connector at one end of the cable to the RJ-45 port on To install the CGETF10xx-10x media con

Resumen del contenido incluido en la página 4

CGETF10xx-10x Operation - Continued Operation Link Pass-Through Pause The Link Pass-Through feature allows the media converter to monitor both the The pause feature can improve network performance by allowing one end of fiber and copper RX (receive) ports for loss of signal. In the event of a loss of the link to signal the other to discontinue frame transmission for a set period an RX signal (1), the media converter will automatically disable the TX of time to relieve buffer congestion. (tran

Resumen del contenido incluido en la página 5

CGETF10xx-10x Cable Specifications Cable Specifications -- Continued The physical characteristics must meet or exceed IEEE 802.3™ specifications. Fiber Cable - Continued CGETF1039-105 850 nm multimode Fiber Cable Fiber Optic Transmitter Power: min: -9.0 dBm max: -4.0 dBm Bit Error Rate: <10-9 Fiber Optic Receiver Sensitivity: min: -17.0 dBm max: -17.0 dBm Single mode fiber (recommended): 9 µm Link Budget: 8.0 dB Multimode fiber (recommended): 62.5/125 µm Multimode fiber (optional): 100/140

Resumen del contenido incluido en la página 6

CGETF10xx-10x Troubleshooting Contact Us If the media converter fails, isolate and correct the fault by determining the Technical support answers to the following questions and then taking the indicated action: Technical support is available 24-hours a day 1. Is the PWR (power) LED illuminated? US and Canada: 1-800-260-1312 NO International: 00-1-952-941-7600  Is the media converter inserted properly into the chassis?  Is the power cord properly installed in the chassis and at the external Tra

Resumen del contenido incluido en la página 7

Compliance Information CISPR22/EN55022 Class A + EN55024 CE Mark FCC regulations This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructio