Resumen del contenido incluido en la página 1
VSK‐2450
USER’S MANUAL
Resumen del contenido incluido en la página 2
TABLE OF CONTENTS INTRODUCTION 1.1 Case Specifications.…..………………………………………………………………………………….. 3 1.2 Diagram…………………………………………………………………….…………………………………. 3 1.3 Power Supply Specifications………………………………………………………………………….4 HARDWARE INSTALLATION GUIDE 2.1 Setting Up….…………………………………………………………………………………………………. 5 2.2 Power Supply Installation……………………………………………………………………………… 5 2.3 Cable Management………………………………………………………………………………………. 5 2.4 Motherboard Installation..……………………………………………………………………………. 6 2.5
Resumen del contenido incluido en la página 3
VSK‐2450 USER’S MANUAL At Antec, we continually refine and improve our products to ensure the highest quality. It’s possible that your new case will differ slightly from the descriptions in this manual. This isn’t a problem; it’s simply an improvement. As of the date of publication, all features, descriptions, and illustrations in this manual are correct. Disclaimer This manual is intended only as a guide for Antec’s computer enclosures. For more comprehensive instructions on instal
Resumen del contenido incluido en la página 4
1.1 CASE SPECIFICATIONS Case Type Mid Tower Color Black Dimensions 450mm (H) x 200mm (W) x 470mm (D) 17.7” (H) x 7.9” (W) x x 18.5” (D) Weight 11.9 lbs / 5.4 kg Cooling 1 x Rear 120mm TwoCool™ fan 2 x Front 120mm fan mounts (optional) TAC 2.0 compliance Drive Bays 10 Drive Bays: ‐ 3 x External 5.25” drive bays ‐ 1 x External 3.5” drive bay ‐ 6 x Internal 3.5” drive bays Expansion Slots 7 Motherboard Size Mini‐ITX, microATX, Standard ATX Front I/O Panel 2 x USB 2.0 AC’9
Resumen del contenido incluido en la página 5
1.3 POWER SUPPLY SPECIFICATIONS The VSK‐2450/VSK‐2450P is powered by a VP‐450/VP‐450P power supply. Input: VP450 Voltage 100 ~ 240VAC ± 10% Frequency Range 50Hz ~ 60Hz Current 9A @ 115VAC, 4.5A @ 230VAC Efficiency Min. 82% VP450P Voltage 200 ~ 240VAC ± 10% Frequency Range 50Hz ~ 60Hz Current 3.5A @ 230VAC Efficiency Min. 80% at full load Output: Voltage: +5V +3.3V +12V +12V ‐12V +5Vsb 1 2 Maximum load 15A 24A 18A 18A 0.8A 2.5A +12V maximum outp
Resumen del contenido incluido en la página 6
HARDWARE INSTALLATION GUIDE 2.1 SETTING UP 1. Place the case upright on a flat, stable surface with the rear of the case facing you. 2. Remove the side panels by first removing the thumbscrews at the rear of the case. Then, grip each panel at the top and bottom and slide it toward the rear of the case until it detaches from the chassis. 3. To remove the front bezel, locate the three plastic tabs on the left side of the bezel. They fasten the front bezel to the metal chassis.
Resumen del contenido incluido en la página 7
2.4 MOTHERBOARD INSTALLATION 1. Lay the case down, with the open side facing up. The drive cages and power supply should be visible. 2. Make sure you have the correct I/O panel for your motherboard. If the panel provided with the case isn’t suitable, please contact your motherboard manufacturer for the correct I/O panel. 3. Align your motherboard with the standoff holes and remember which holes are lined up. Not all motherboards will match with all the provided holes; this i
Resumen del contenido incluido en la página 8
2.6 EXTERNAL 3.5” DEVICE INSTALLATION There is one 3.5” drive bay available just below the 5.25” drive bays at the front of the case. Before you begin, remove the side panels and front bezel of the case as described in section 2.1. 1. Slide your 3.5” device into the drive bay from the front and align the screw holes on the devices with the corresponding holes in the chassis. 2. Fasten the device in place with the provided screws. 3. Connect the appropriate power and data cables.
Resumen del contenido incluido en la página 9
3.2 AC’97 / HD AUDIO PORTS There is an Intel® standard 10‐pin AC’97 connector and an Intel® 10‐pin HDA (High Definition Audio) connector linked to the front panel of the case. Signal Names Signal Names Pin Pin (HDA) (AC’97) 1 MIC2 L 1 MIC In 2 AGND 2 GND 10 6 4 2 3 MIC2 R 3 MIC Power 4 AVCC 4 NC 5 FRO-R 5 Line Out (R) 9 7 5 3 1 6 MIC2_JD 6 Line Out (R) 7 F_IO_SEN 7 NC 8 Key (no pin) 8 Key (no pin) 9 FRO-L 9 Line Out (L) 10 LINE2_JD 10 Li
Resumen del contenido incluido en la página 10
3.4 REWIRING MOTHERBOARD HEADER CONNECTIONS There may come a time when you need to reconfigure the pin‐out of a motherboard header connector. Examples could be for your USB header, audio input header, or some other front panel connector such as the Power Button connector. Before performing any work, please refer to your motherboard user’s manual or your motherboard manufacturer's website to be sure of the pin‐out needed for your connector. We strongly recommend making a notated dr
Resumen del contenido incluido en la página 11
COOLING SYSTEM 4.1 TWOCOOL™ FANS Rear TwoCool™ Fan – There is a 120 x 25mm Two‐Cool™ fan preinstalled at the rear of the case. The fan is installed so the air will be blown out of the case. This fan comes with a two‐speed switch that let you choose the speed best suited to your need. The default fan speed setting is Low. 120mm TwoCool™ Specifications Size: 120 x 25mm TwoCool™ fan Rated Voltage: 12V Operating Voltage: 10.8V ~ 13.2 V Speed Input Static Acoustic Input
Resumen del contenido incluido en la página 12
4.3 OPTIONAL FANS There are a total of two optional 120mm fan mounts—two front intake fans (at the front of the HDD cage). We recommend using Antec 120mm speed control fans and setting the speed to Low. These fans must be installed so that the air is blowing into the case. Note: In order to build a quieter system, we recommend NOT installing the optional fans unless it is necessary for cooling. If you choose to install them we recommend using Antec 120mm speed controlled fans and
Resumen del contenido incluido en la página 13
Antec, Inc. 47900 Fremont Blvd. Fremont, CA 94538 USA tel: 510‐770‐1200 fax: 510‐770‐1288 Antec Europe B.V. Stuttgartstraat 12 3047 AS Rotterdam Netherlands tel: +31 (0) 10 462‐2060 fax: +31 (0) 10 437‐1752 Customer Support: US & Canada 1‐800‐22ANTEC customersupport@antec.com Europe +31 (0) 10 462‐2060 europe.techsupport@antec.com www.antec.com © Copyright 2009 Antec, Inc. All rights reserved. All trademarks are the property of their
