Manual de instrucciones de Transition Networks CBFTF10XX-15X

Resumen del contenido incluido en la página 1

USER’S GUIDE
CBFTF10xx-15x
Slide-in-Module Media Converter
• Copper to Fiber
 10/100 Bridging (2-Port)
 10Base-T/100Base-TX to 100Base-FX
The CBFTF10xx-15x 2-port Ethernet/Fast Ethernet
bridging Media Converter is designed to be
installed in a Transition Networks PointSystem™
chassis and connects 10Base-T Ethernet or
100Base-TX Fast Ethernet twisted-pair copper
network devices to network devices on a 100Base-
FX Fast Ethernet fiber network.
Part Number Port One - Copper Port Two - Duplex Fiber

Resumen del contenido incluido en la página 2

CBFTF10xx-15x INSTALLATION INSTALLATION -- Continued CAUTION: Wear a grounding device and observe electrostatic discharge Set the Jumpers precautions when setting the 4-position switch and the jumper(s) and when The jumpers are located on the Media Converter circuit board. Use small installing the Slide-in-Module. Failure to observe this caution could result in needle-nosed pliers or a similar device to set the jumper. damage to, and subsequent failure of, the Media Converter. The Hardware/So

Resumen del contenido incluido en la página 3

CBFTF10xx-15x INSTALLATION -- Continued INSTALLATION -- Continued Install the Twisted-Pair Copper Cable Power the Media Converter 1. Locate or build IEEE 803.2™ compliant 10Base-T or 100Base-TX cables, The CBFTF10xx-15x Slide-in-Module Media Converter is powered through the with straight-through RJ-45 cable, and with straight-through RJ-45 Point System™ chassis. connectors installed at both ends. 2. Connect the RJ-45 connector at one end of the cable to the RJ-45 port OPERATION connector on th

Resumen del contenido incluido en la página 4

CBFTF10xx-15x OPERATION - Continued OPERATION - Continued Product Features Product Features - Continued Auto-Negotiation Full-Duplex Network The Auto-Negotiation feature allows the Media Converter to be used with In a full-duplex network, maximum cable lengths are determined by the type 10Base-T and 100Base-TX twisted-pair ports. Using Auto-Negotiation, the of cables that are used. See page 1 (front cover) for the cable specifications Media Converter brings up the copper links in the highest sp

Resumen del contenido incluido en la página 5

CBFTF10xx-15x CABLE SPECIFICATIONS TECHNICAL SPECIFICATIONS The physical characteristics must meet or exceed IEEE 802.3™ specifications. For use with Transition Networks Model CBFTF10xx-15x or equivalent. Fiber Cable Standards IEEE 802.3™ Bit Error Rate: <10-9 Data Rate: 10 Mb/s, 100 Mb/s Singlemode fiber (recommended): 9 µm Dimensions 3.4" x 4.7" x 0.87" (86 mm x 119 mm x 22 mm) Multimode fiber (recommended): 62.5/125 µm Multimode fiber (optional): 100/140, 85/140, 50/125 µm Weight 4 oz.

Resumen del contenido incluido en la página 6

CBFTF10xx-15x FAULT ISOLATION AND RECOVERY CONTACT US If the Media Converter fails, isolate and correct the failure by determining the Technical Support answers to the following questions and then taking the indicated action: Technical support is avialable 7:00 AM - 6:00 PM CST (GMT -6:00) 1. Is the power LED on the Media Converter illuminated? US and Canada: 1-800-260-1312 NO International: 00-1-952-941-7600  Is the media converter inserted properly into the chassis? Transition Now  Is the po

Resumen del contenido incluido en la página 7

COMPLIANCE INFORMATION UL Listed C-UL Listed (Canada) CISPR22/EN55022 Class A CE Mark FCC Regulations This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accorda