Resumen del contenido incluido en la página 1
Model: MPN1-08CR
MPN1-10CR
Inside you will find many helpful hints on how to use and maintain your air conditioner properly. Just
a little preventative care on your part can save you a great deal of time and money over the life of
your air conditioner. Before operating this product, please read the instructions carefully and save this
manual for future use.
PORTABLE AIR CONDITIONER
Resumen del contenido incluido en la página 2
CONTENTS SAFETY PRECAUTIONS Safety rules ........................................................................................................................................2 Electrical information ..........................................................................................................................2 IDENTIFICATION OF PARTS Accessories ........................................................................................................................................3
Resumen del contenido incluido en la página 3
SAFETY PRECAUTIONS Safety rules To prevent injury to the user or other people and property damage, the following instructions must be followed. Incorrect operation due to ignoring of instructions may cause harm or damage. Always do this Never do this ! Do not operate your air conditioner in a wet room such as a bathroom or laundry room. Your air conditioner should be used in such a way Do not touch the unit with wet or damp hands or that it is protected from moisture. e.g. condensation, when b
Resumen del contenido incluido en la página 4
F IDENTIFICATION OF PARTS Accessories O Check all the accessories are included in the package and please refer to the installation instructions for their usage. Suggested tools for window kit installation 1. Screwdriver(medium size Phillips) 2. Tape measure or ruler 3. Knife or scissors 4. Saw(In the event that the window kit needs to be cut down in size because the window is too narrow for direct installation) 3
Resumen del contenido incluido en la página 5
IDENTIFICATION OF PARTS NAMES OF PARTS Before Using This Air Conditioner, be Sure To Check The Back Of The Unit To Make Sure That The Lower Drain Plug Is Security 12 In Place . See Fig.2 FRONT VIEW 1 Operation Panel 1 2 Horizontal Louvers 2 4 3 Caster 4 Carrying Handle (both sides) 3 Fig.1 Upper Air Filter 5 REAR VIEW (Behind the grille) Air Outlet 6 5 8 Power cord outlet 7 Air intake 8 9 6 Drain Outlet 9 10 10 Air intake Lower Air Filter 11 7 11 (Behind the grille) 12 Bottom Drain Plug 12 Fig.2
Resumen del contenido incluido en la página 6
AIR CONDITIONER FEATURES ELECTRONIC CONTROL OPERATING INSTRUCTIONS Before you begin, thoroughly familiarize yourself with the control panel and remote controller and all functions, then follow the symbol for the functions you desire. The unit can be controlled by the unit control panel alone or with the remote controller . OPERATION PANEL OF THE AIR CONDITIONER 6 4 4 4 4 5 SWING HI AUTO COOL F C MED DRY TIMER ON MODE SLEEP FAN LOW TIMER OFF FAN 1 2 3 7 8 Fig.3 1 POWER button NOTE: Power switch o
Resumen del contenido incluido en la página 7
AIR CONDITIONER FEATURES 3 FAN button NOTE: Used to select the Fan Speed in four steps- LOW, MED ,HI and AUTO. The fan speed indicator light illuminates HI under different fan settings except AUTO F C MED speed. Each time the button is pressed, TIMER ON SLEEP FAN the fan speed mode is shifted. LOW TIMER OFF UP( ) and DOWN( ) button 4 NOTE: Used to adjust (increasing/decreasing) Press to increase Press to decrease temperature settings(1 C/2 F increments) in a range of 17 C(62 F) to 30 C(88
Resumen del contenido incluido en la página 8
AIR CONDITIONER FEATURES Use the SWING button to adjust the UP/DOWN SWING button airflow direction (Perform this function while the unit is in operation). 1. Press the SWING button, the swing feature is SWING activated. o AUTO COOL 2. Each press will change the swing angle for 6 . F C DRY TIMER ON Keep pressing the button to move the horizontal MODE TIMER OFF louver to the desired position. FAN If keep pressing the SWING button without releasing for 2 more seconds, the horizontal louver would s
Resumen del contenido incluido en la página 9
AIR CONDITIONER FEATURES NOTE: TIMER button When the unit is on, first press the Timer button, the indicator light above word TIMER OFF illu- minates. It indicates the Auto Stop program is initiated. SWING When the unit is off, first press the Timer button, AUTO COOL the indicator light above word TIMER ON illu- F C DRY TIMER ON minates. It indicates the Auto Start program is MODE TIMER OFF initiated. FAN Press or hold the UP arrow or DOWN arrow to change the Auto time by 0.5 hour increments,
Resumen del contenido incluido en la página 10
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS 1 COOL OPERATION - Press the "MODE" button several times until the "COOL" indicator light comes on. - Press the UP and DOWN buttons or to select your desired room temperature. O O O O The temperature can be set within a range of 17 C-30 C/62 F-88 F. - Press the "FAN " button to choose the fan speed. 2 DRY OPERATION (DEHUMIDIFY) - Press the "MODE" button until the "DRY" indicator light comes on. - Under this mo
Resumen del contenido incluido en la página 11
OPERATING INSTRUCTIONS 6 WATER DRAINAGE: During dehumidifying mode: - Remove the drain plug from the back of the unit,attach a section of drain hose (included with this unit) to the hole. Place the open end of the hose directly over the drain area in your basement floor or in a water container (see Fig.4 & 5). - You can also install the drain connector (5/8" (1.58cm) universal female mender) with 3/4" (1.9cm) hose (locally purchased by consumer) for garden hose use. NOTE: - When the water le
Resumen del contenido incluido en la página 12
30cm (0.98ft) INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS Location The air conditioner should be placed on a firm foundation to minimize noise and vibration. For safe and secure positioning, place the unit on a smooth, level floor strong enough to support the unit. The unit has casters to aid placement, but it should only be rolled on smooth, flat surfaces. Use caution when rolling on carpet surfaces. Do not attempt to roll the unit over objects. The unit must be placed within reach of a
Resumen del contenido incluido en la página 13
INSTALLATION INSTRUCTIONS Installation in double-hung sash windows Foam seal A 1. Cut the foam seal(adhesive type) to the proper length and (adhesive type) attach it to the window stool. Fig.10 Fig.10 2. Attach the window slider kit to the window stool. Adjust the length of the window slider kit according to the width of window, shorten the adjustable window kit if the width of window is less than 27 inches. Window kit Open the window sash and place the window slider kit on the window stool. Fig
Resumen del contenido incluido en la página 14
INSTALLATION INSTRUCTIONS Installation in a sliding sash windows Foam seal A 1. Cut the foam seal(adhesive type) to the proper length and (adhesive type) attach it to the window frame. See Fig.14. Fig.14 2. Attach the window slider kit to the window stool. Adjust the length of the window slider kit according to the width of window, shorten the adjustable window kit if the width of Window kit window is less than 27 inches. Open the window sash and place the window slider kit on the window stool.
Resumen del contenido incluido en la página 15
INSTALLATION INSTRUCTIONS Exhaust hose installation: The exhaust hose and adaptor must be installed or removed Flat mouth in accordance with the usage mode. COOL mode Install Fig.18 Remove FAN or DEHUMIDIFY mode Install the window Exhaust adaptor (flat mouth) onto the 1. exhaust hose as shown in Fig.18. Refer to the previous pages for window kit installation. Hook 2. Place the Exhaust hose over against the air outlet opening Fig.19 hook(See Fig.19) and flat the other end(See Fig.20) for quick i
Resumen del contenido incluido en la página 16
CARE AND MAINTENANCE CARE AND MAINTENANCE Air filter (slide out) IMPORTANT: 1) Be sure to unplug the unit before cleaning or servicing. 2) Do not use gasoline, thinner or other chemicals to clean the unit. 3) Do not wash the unit directly under a tap or using a hose. It may cause electrical danger. 4) If the power cord is damaged, it should be repaired by Fig.22 manufacturer or its agent. 1. Air filter - Clean the air filter at least once two weeks to prevent inferior fan operation beca
Resumen del contenido incluido en la página 17
TROUBLESHOOTING TIPS TROUBLE SHOOTING TROUBLES POSSIBLE CAUSES SUGGEST REMEDIES 1. Unit does not - P1 appears in the display window Drain the water in the bottom tray. Start when Pressing on/off - Room temperature is lower than Reset the temperature. Button the set temperature.(Cooling mode) - The windows or doors in the room Make sure all the windows and are not closed. doors are closed. - There are heat sources inside the Remove the heat sources if possible. 2. Not cool enough room. - E
Resumen del contenido incluido en la página 18
SET TEMPERATURE( F) AUTO FAN COOL HIGH DRY MED LOW TEMP MODE ON/OFF FAN SPEED SWING ECONOMY TIMER ON RESET LOCK TIMER OFF DISPLA LED Y 8m REMOTE CONTROLLER ILLUSTRATION Handling the remote controller Location of the remote controller. Use the remote controller within a distance of 8 meters from the appliance, pointing it towards the receiver. Reception is confirmed by a beep. CAUTIONS The air conditioner will not operate if curtains, doors or other materials block the signals from the remote c
Resumen del contenido incluido en la página 19
REMOTE CONTROLLER ILLUSTRATION Remote Controller Specifications Model R51I13/BG(C)E Rated Voltage 3.0V(Dry batteries R03/LR03 ¡` 2) Lowest Voltage of 2.0V CPU Emitting Signal 8m (when using 3.0 voltage, it Gets 11m) Signal Receiving Range ¡£ ¡£ O O Environment -5 C 60 C( ) -41 F~140 F ~ NOTE: Temperature setting display: Fahrenheit scale( F), R51I13/BG(C)E Performance Feature 1. Operating Mode: AUTO, COOL, DRY, and FAN. 2. Timer Setting Function in 24 hours. ¡£ ¡£ O O 3.
Resumen del contenido incluido en la página 20
REMOTE CONTROLLER ILLUSTRATION Function buttons continued 8 TIMER ON Button Press this button to activate the Auto-on time setting. Each press will increase the time setting in 30 minutes increments, up to 10 hours, then at 1 hour increments up to 24 hours. To cancel the Auto-on time setting, SET TEMPERATURE( F) just press the button until the time setting is 0.0. AUTO FAN COOL HIGH DRY MED 9 LOW ECONOMY(SLEEP) Button Select this function during the sleeping time. It can maintain the most TEMP
