Resumen del contenido incluido en la página 1
[ Quick Start Guide ]
INTELL IGENT ST ORAGE ROUT ER INSTALL AT ION
z
iSR6250
QUICK START GUIDE
Resumen del contenido incluido en la página 2
Purchasers of OEM products should consult with the OEM for support. Please feel free to contact your QLogic approved reseller or QLogic Technical Support at any phase of integration for assistance. QLogic Technical Support can be reached by the following methods: Web http://support.qlogic.com E-mail support@qlogic.com The QLogic knowledge database contains troubleshooting information for the QLogic HBAs. Access the data base from the QLogic Support Web page, http://support.qlogic.com. Use th
Resumen del contenido incluido en la página 3
Quick Start Guide The iSR6250 is an intelligent storage router that provides servers with iSCSI connectivity to SAN-attached Fibre Channel-based disk or tape storage. Suggested Configurations Figure 1 shows the iSR6250 connecting iSCSI servers to a direct-attached storage array. iSCSI FC iSCSI iSCSI iSR6250 Initiator IP Switched Network Server RAID Based Fibre Channel Storage System Figure 1. iSR6250 in Direct Attach Configuration Figure 2 shows the iSR6250 connecting iSCSI servers to a SAN-
Resumen del contenido incluido en la página 4
Installation Instructions This Quick Start Guide describes how to install and configure your new QLogic iSR6250 router by following these steps: ❑ Step 1. Verify the package contents. ❑ Step 2. Complete the pre-installation checklist. ❑ Step 3. Mount the router. ❑ Step 4. Install the SFPs. ❑ Step 5. Apply power to the iSR6250 router. ® ❑ Step 6. Install the SANsurfer Router Manager. ❑ Step 7. Configure iSR6250 management port IP address. ❑ Step 8. Run the configuration wizard. ❑ Step 9. Present
Resumen del contenido incluido en la página 5
Table 1. Worksheet for Router Blade 1 (left) Parameters (Continued) IP address of the iSNS server for iSCSI port 2 (if iSNS will be enabled) iSCSI port 3 IP address, subnet mask, and gateway for the 10GbE-1 port IP address of the iSNS server for iSCSI port 3 (if iSNS will be enabled) iSCSI port 4 IP address, subnet mask, and gateway for the 10GbE-2 port IP address of the iSNS server for iSCSI port 4 (if iSNS will be enabled) Table 2. Worksheet for Router Blade 2 (right) Parameters Symbolic
Resumen del contenido incluido en la página 6
10GbE2 10GbE1 iSR6250 Intelligent Storage Router 10GbE2 10GbE1 iSR6250 Intelligent Storage Router Step 3. Mount the Router Mount the router in the rack using the rack mount kit with instructions provided. Step 4. Install the SFPs An SFP transceiver is required for each router port that will be connected to a Fibre Channel device or switch. SFPs are included in the package. If you prefer using different SFP transceivers from the ones provided, purchase one of the following QLogic recommended tr
Resumen del contenido incluido en la página 7
10GbE2 10GbE1 iSR6250 Intelligent Storage Router Power LED 10Gb iSCSI Ports RS232 Port Heartbeat LED GE4 GE3 iSR6240 Intelligent Storage Router iSR6200 System MGMT IOIOI FC1 FC2 GE1 GE1 FC iSCSI System Fault LED Management Port Ports Ports Figure 4. iSR6250 Blade Ports and LEDs 4. Verify that the router’s input power LED is illuminated. The iSR6250 router runs its self test and begins normal operation—this may take a minute. 5. Verify that the heartbeat LED is blinking (once per second) and t
Resumen del contenido incluido en la página 8
Step 7. Configure iSR6250 Management Port IP Address 1. Connect the router’s Management Port (10/100 Ethernet) to your workstation using a switch or hub. As an alternative, you may connect your workstation directly to the router using an Ethernet crossover cable. The iSR6250 management port’s default IP address is 10.0.0.1 subnet 255.0.0.0. Make sure the workstation connected to the iSR6250 router has Ethernet address 10.0.0.x, where x is other than 1 and subnet mask is 255.0.0.0. 2. From the
Resumen del contenido incluido en la página 9
Step 8. Run the Configuration Wizard ® 1. Start the SANsurfer Router Manager previously installed on the computer that will manage the iSR6250. You should see a display as shown in the following figures. 2. Click the Connect button on the top-left corner. 3. Enter the IP address of the iSR6250 you want to configure. 4. Select the router blade to be configured (Blade 1 or 2) from the system tree (in left panel). 5. Click Yes to start the configuration wizard. The following screen appears: 9
Resumen del contenido incluido en la página 10
6. Enter the Symbolic Name for this router. 7. Select each iSCSI port and use the wizard to enter IP addresses for the iSCSI port, and optionally, the IP address of an iSNS server. NOTE: QLogic recommends that you enable Flow Control for your 10GbE interfaces (10GbE1 and 10GbE2 ports). You must also enable Flow Control on the Ethernet switch to which you are connecting the router. Ethernet flow control is defined by IEEE 802.3x. 8. Save the changes; the default password is “config.” 9. Copy
Resumen del contenido incluido en la página 11
Step 9. Present LUNs to iSCSI Initiators 1. If the iSR6250 is connected in the FC fabric, make sure the FC fabric zoning is set so that FC storage array ports and router FC ports are in the same zone. 2. Using storage array management software, create all LUNs you want to present to all iSCSI initiators through this iSR6250. Present the LUNs from the FC storage array to the iSR6250 using WWPNs of this iSR6250. If you are setting up a high availability configuration that uses two iSR6250s as a
Resumen del contenido incluido en la página 12
c. Launch the Presentation Wizard from the Wizards drop-down menu. This wizard allows you to map a LUN to the iSCSI initiator on your server. The screen that allows this mapping looks like this: d. Save the mappings using your management password. 12
Resumen del contenido incluido en la página 13
e. Refresh the SANsurfer Router Manager display. Now, when you select your iSCSI initiator on the LHS of the display, you should be able to see the LUNs mapped to that initiator as follows: f. Return to the Windows Server screen and select LogOn to log on to this target. The status should change from Inactive to Connected. Step 10. Configure Second Blade Repeat steps 8 and 9 for the second blade. Congratulations! You have now successfully installed your QLogic iSR6250 and mapped target LUNs t
Resumen del contenido incluido en la página 14
Troubleshooting and Technical Support For technical support, visit the QLogic website, support.qlogic.com or send an email to support@qlogic.com. Warranty The QLogic iSR6250 router comes with a standard one-year QLogic warranty, or as specified by other agreements. Check the QLogic Web site at www.qlogic.com for warranty details. Regulatory Information (Preliminary) The following sections contain a summary of EMC/EMI test specifications performed on the QLogic iSR6250 router to comply with rad
Resumen del contenido incluido en la página 15
© 2009 QLogic Corporation. QLogic, the QLogic logo, SANbox, and Enterprise Fabric Suite 2007 are registered trademarks or trademarks of QLogic Corporation. All other brands and product names are trademarks or registered trademarks of their respective owners. Information supplied by QLogic is believed to be accurate and reliable. QLogic Corporation assumes no responsibility for any errors in this brochure. QLogic Corporation reserves the right, without notice, to makes changes in product design o
Resumen del contenido incluido en la página 16
*SN0054545-00 A* QLogic Corporation 26650 Aliso Viejo Parkway Aliso Viejo, CA 92656 949.389.6000 www.qlogic.com SN0054545-00 A
