Resumen del contenido incluido en la página 1
Wireless Outdoor Bridge
XI-1500-IH
Quick Installation Guide
2.9.3
1
Resumen del contenido incluido en la página 2
Table of Contents XI-1500-IH Introduction Appearance of products Hardware Installation Product kit Hardware Installation Initialize Configuation PC Use the function of bridge graft fast 2
Resumen del contenido incluido en la página 3
XI-1500-IH Introduction The new-generation wireless LAN device – 11Mbps Wireless Inter-building Access Point, XI-1500-IH is specially designed for Point-to-Point and Point-to-Multipoint applications, offering campus-wide connections between buildings at a speed of up to 11Mbps. The new features and benefits are, support POE (Power over Ethernet), support test-link, use this utility, you can point the antenna to the best direction, Fully compliant with IEEE802.11b standard, the Wirele
Resumen del contenido incluido en la página 4
Hardware Installation Take the following steps to set up the Wireless Outdoor Bridge. Hardware equipment Fixation First you should fix the Wireless Outdoor Bridge, the following figure show it: Connect the Ethernet Cable The Wireless Outdoor Bridge supports 10/100M Ethernet connection. Attach UTP Ethernet cable to the RJ-45 connector on the Wireless Outdoor Bridge. Then connect the other end of the RJ-45 cable to a hub or a station. Please note that, use t
Resumen del contenido incluido en la página 5
Plug water-joint into the Wireless Outdoor Bridge Close the water-joint Note Two LEDs in the cable connecter of the XI-1500-IH. A DEFAULT button aside of the LEDs. The DEFAULT button restore the factory default settings. Warning Please make sure the Wireless Outdoor Bridge to DC Ground. Initialize Have initial value , network of bridge whether which is short of province parameter set up , is it install after finishing is it can make working to it to supply powering
Resumen del contenido incluido en la página 6
Configuration PC This section introduces you how to configuration TCP/IP protocol into your personal computer. And suppose you have been successfully installed one network card on your personal computer. Windows 98/Me 1 Click the Start button, select Settings, then select Control Panel 2 Double-click the Network Icon 3 In the configuration tab, select the TCP/IP protocol line that is associated with your network card/adapter. If there is no TCP/IP line listed, you will need to firs
Resumen del contenido incluido en la página 7
7
Resumen del contenido incluido en la página 8
Build Point-to-Point and Point-to-Multipoint Step 1 The hardware is installed. Note: Please configuration all the parameters of the Wireless Outdoor Bridge according to the actual conditions indoors. Install the Wireless Outdoor Bridge to the bracket after the wireless chain is adjusted openly. Note: The bracket that should be possible is high while installing the Wireless Outdoor Bridge. 2 The equipment is initialized. 3 Use the Utility or WEB Management. Method A:
Resumen del contenido incluido en la página 9
The bridge’s IP differ from the computer’s IP, you can also find the bridge from utility. Double click an Wireless Outdoor Bridge icon to access its property dialog box. Enter the password in the entry field. The default password is “default”. After entering the correct password, a configuration window appears. 4 Configuration the parameter of XI-1500-IH, include Radio Mode, Channel, Tx Rate: Warning: XI-1500-IH is used in pairs when work as the bridge mode, so Radio M
Resumen del contenido incluido en la página 10
Note: If you experience interference (shown by lost connections and/or slow data transfers) you may need to experiment with different channels to see which is the best. 5 Configuration IP Address Note: To enable remote access to the Wireless Outdoor Bridge using Web Management, you must assign an IP address to the Wireless Outdoor Bridge. 6 Test-link Click “Test-link” to the test-link mode MyMacAddress show MacAddress of local AP. 10
Resumen del contenido incluido en la página 11
TTestMacAddress-fill MacAddress of remote AP. Transmit Pkt Num-display the number of frame be sended. RcvPkNumLabel-display the number of frame be received. Recv/Trans Rate-display the successful rate of transmitting. Time Elapsed-show the time cost of sending data. Local Signal Level show local signal level. Remote Signal Level show remote signal level. Note: View the intensity of signal, and adjust the positions and angles of the antenna according to the intensity of signal. Adju
Resumen del contenido incluido en la página 12
Method B: Using WEB management The built-in Web Management provides you with a user-friendly graphical user interface to manage the AP. The AP with an assigned IP address (e.g. http://192.168.1.1) will allow you via web browser (e.g. Netscape Navigator 3.0 ~ 4.5 or MS Internet Explorer 4.0) to monitor and configure. Enter the password to login to the AP. The default password is default 1. configuration IP address 12
Resumen del contenido incluido en la página 13
2. Configuration the parameter of XI-1500-IH, include Radio Mode, Channel, Tx Rate Troubleshooting If you meet difficulty and please contact our supplier in the course of installing and using the Wireless Outdoor Bridge. 13
