Resumen del contenido incluido en la página 1
Vigor2820 Series
ADSL2/2+ Security Firewall
Quick Start Guide
Version: 1.0
Date: 2007/07/24
i
Resumen del contenido incluido en la página 2
Copyright Information Copyright Copyright 2007 All rights reserved. This publication contains information that is Declarations protected by copyright. No part may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language without written permission from the copyright holders. Trademarks The following trademarks are used in this document: Microsoft is a registered trademark of Microsoft Corp. Windows, Windows 95, 98, Me, NT, 2000, XP and
Resumen del contenido incluido en la página 3
European Community Declarations Manufacturer: DrayTek Corp. Address: No. 26, Fu Shing Road, HuKou County, HsinChu Industrial Park, Hsin-Chu, Taiwan 303 Product: Vigor2820 Series Router DrayTek Corp. declares that Vigor2820 Series of routers are in compliance with the following essential requirements and other relevant provisions of R&TTE Directive 1999/5/EEC. The product conforms to the requirements of Electro-Magnetic Compatibility (EMC) Directive 2004/108/EC by complying with the r
Resumen del contenido incluido en la página 4
T Ta ab blle e o of f C Co on nt te en nt ts s 1. Introduction........................................................................................................... 1 1.1 Panel Explanation ...................................................................................................................... 2 1.1.1 For Vigor2820 ............................................................................................................... 2 1.1.2 For Vigor2820n .....................
Resumen del contenido incluido en la página 5
1. Introduction 1. Introduction nd nd The Vigor2820 is an ADSL2+ router with 2 Ethernet WAN. This 2 WAN can connect to DSL/Cable modem or fiber media converter for policy-based load-balance, fail-over and BoD (Bandwidth on Demand); it also features advanced bandwidth control mechanism such as IP-layer QoS, NAT Session Limitation, Bandwidth Borrowed, etc., to allow easy, flexible, reliable access control and bandwidth management. The SPI (Stateful Packet Inspection) firewall uses object-
Resumen del contenido incluido en la página 6
1.1 Panel Explanation 1.1 Panel Explanation 1.1.1 For Vigor2820 1.1.1 For Vigor2820 LED Status Explanation ACT (Activity) Blinking The router is powered on and running normally. Off The router is powered off. USB On A USB device is connected and active. Blinking The data is transmitting. CSM On The profile of CSM (Content Security Management) for IM/P2P application is active. (It is enabled from Objects Setting >> CSM Profile). CPA (Content Portal On The Web Content Filter is ac
Resumen del contenido incluido en la página 7
Interface Description Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration. LAN (1-4) Connecters for local networked devices. DSL Connecter for accessing the Internet through ADSL2/2+. WAN 2 Connecter for remote networked devices. USB Connecter
Resumen del contenido incluido en la página 8
1 1..1 1..2 2 F Fo or r V Viig go or r2 28 82 20 0n n LED Status Explanation ACT (Activity) Blinking The router is powered on and running normally. Off The router is powered off. USB On A USB device is connected and active. Blinking The data is transmitting. CSM On The profile of CSM (Content Security Management) for IM/P2P application is active. (It is enabled from Objects Setting >> CSM Profile). WLAN On Wireless access point is ready. Blinking It will blink while wireless t
Resumen del contenido incluido en la página 9
Interface Description WLAN Push this button to enable (WLAN LED on) or disable (WLAN LED off) wireless connection. Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration. LAN (1-4) Connecters for local networked devices. DSL Connecter for accessing
Resumen del contenido incluido en la página 10
1 1..1 1..3 3 F Fo or r V Viig go or r2 28 82 20 0V Vn n LED Status Explanation ACT (Activity) Blinking The router is powered on and running normally. Off The router is powered off. USB On A USB device is connected and active. Blinking The data is transmitting. CSM On The profile of CSM (Content Security Management) for IM/P2P application is active. (It is enabled from Objects Setting >> CSM Profile). WLAN On Wireless access point is ready. Blinking It will blink while wireles
Resumen del contenido incluido en la página 11
Interface Description WLAN Push this button to enable (WLAN LED on) or disable (WLAN LED off) wireless connection. Factory Reset Restore the default settings. Usage: Turn on the router (ACT LED is blinking). Press the hole and keep for more than 5 seconds. When you see the ACT LED begins to blink rapidly than usual, release the button. Then the router will restart with the factory default configuration. Phone 1/2 Connecter for PSTN phone. Line Connector of analog phone for PSTN li
Resumen del contenido incluido en la página 12
1 1..1 1..4 4 F Fo or r V Viig go or r2 28 82 20 0V VS S LED Status Explanation ACT (Activity) Blinking The router is powered on and running normally. Off The router is powered off. USB On A USB device is connected and active. Blinking The data is transmitting. CSM On The profile of CSM (Content Security Management) for IM/P2P application is active. (It is enabled from Objects Setting >> CSM Profile). CPA (Content Portal On The Web Content Filter is active. (It is enabled from
Resumen del contenido incluido en la página 13
Left LED On The port is connected. LAN 1(Giga) (Green) Off The port is disconnected. Blinking The data is transmitting. Right LED On The port is connected with 1000Mbps. (Green) Off The port is disconnected with 10/100Mbps. Left LED On The port is connected. LAN 2/3/4 (Green) Off The port is disconnected. Blinking The data is transmitting. Right LED On The port is connected with 100Mbps. (Green) Off The port is disconnected with 10Mbps. Left LED On The port is connected. WAN 2
Resumen del contenido incluido en la página 14
1 1..1 1..5 5 F Fo or r V Viig go or r2 28 82 20 0V VS Sn n LED Status Explanation ACT (Activity) Blinking The router is powered on and running normally. Off The router is powered off. USB On A USB device is connected and active. Blinking The data is transmitting. CSM On The profile of CSM (Content Security Management) for IM/P2P application is active. (It is enabled from Objects Setting >> CSM Profile). WLAN On Wireless access point is ready. Blinking It will blink while wire
Resumen del contenido incluido en la página 15
Blinking The data is transmitting. Right LED On The port is connected with 1000Mbps. (Green) Off The port is disconnected with 10/100Mbps. Left LED On The port is connected. LAN 2/3/4 (Green) Off The port is disconnected. Blinking The data is transmitting. Right LED On The port is connected with 100Mbps. (Green) Off The port is disconnected with 10Mbps. Left LED On The port is connected. WAN 2 (Green) Off The port is disconnected. Blinking The data is transmitting. Right LED O
Resumen del contenido incluido en la página 16
1.2 Package Content 1.2 Package Content Quick Start Guide CD RJ-45 Cable (Ethernet) RJ-45 to RJ-45 Cable for S models ISDN Phone Adapter (VS models) Analog Phone Adapter (V models) The type of the power adapter depends on the country that the router will be installed: UK-type Power Adapter EU-type Power Adapter USA/Taiwan-type Power Adapter AU/NZ-type Power Adapter * The maximum power consumption is 17-23 Watt. 12
Resumen del contenido incluido en la página 17
2. Installing Your Router 2. Installing Your Router This section will guide you to install the router through hardware connection and configure the router’s settings through web browser. 2 2..1 1 H Ha ar rd dw wa ar re e I In ns st ta alllla at tiio on n Before starting to configure the router, you have to connect your devices correctly. 1. Connect the ADSL interface to the external ADSL splitter with an ADSL line cable for all models. For Vigor2820Vn/VS/VSn, also connect Line inter
Resumen del contenido incluido en la página 18
Caution: Each of the Phone ports can be connected to an analog phone only. Do not connect the phone ports to the telephone wall jack. Such connection might damage your router. 2 2..2 2 I IS SD DN N P Ph ho on ne e A Ad da ap pt te er r I In ns st ta alllla at tiio on n Such information is provided for Vigor2820 S models (e.g., Vigor2820VS/VSn). Phone S0 is always fixed to connect ISDN phone. However, ISDN /Phone S0 is configurable as NT or TE mode. When the user configures ISDN /
Resumen del contenido incluido en la página 19
Yet, if the user configures ISDN / Phone S0 as TE Mode in VoIP>> Phone Settings, the green LED will light on to indicate ISDN-TE is selected. Then, the port is specified for ISDN line only. Refer to the following figure for reference. 15
Resumen del contenido incluido en la página 20
2.3 Printer Installation 2.3 Printer Installation You can install a printer onto the router for sharing printing. All the PCs connected this router can print documents via the router. The example provided here is made based on Windows XP/2000. For Windows 98/SE, please visit www.draytek.com. Before using it, please follow the steps below to configure settings for connected computers (or wireless clients). 1. Connect the printer with the router through USB/parallel port. 2. Open Start
