Manual de instrucciones de Cisco Systems Cisco Aironet Wireless Access Point AIRSAP2602EAK9

Manual de instrucciones del aparato Cisco Systems Cisco Aironet Wireless Access Point AIRSAP2602EAK9

Aparato: Cisco Systems Cisco Aironet Wireless Access Point AIRSAP2602EAK9
Categoría: Tarjeta de red
Fabricante: Cisco Systems
Tamaño: 1.29 MB
Fecha de añadido: 8/7/2013
Número de páginas: 38
Imprimir el manual

Descargar

¿Cómo se utiliza?

Nuestro propósito es proporcionarte el acceso más rápido posible a los contenidos incluidos en los manuales de instrucciones del aparato Cisco Systems Cisco Aironet Wireless Access Point AIRSAP2602EAK9. Utilizando la vista previa online, puedes ver rápidamente el índice de contenidos y pasar a la página donde encontrarás la solución a tu problema con Cisco Systems Cisco Aironet Wireless Access Point AIRSAP2602EAK9.

Para tu comodidad

Si ver los manuales de instrucción de Cisco Systems Cisco Aironet Wireless Access Point AIRSAP2602EAK9 directamente en esta página no es cómodo para ti, puedes utilizar dos soluciones posibles:

  • Vista en pantalla completa – Para ver cómodamente los manuales de instrucciones (sin descargarlos en tu ordenador) puedes utilizar el modo de vista en pantalla completa. Para activar la vista del manual Cisco Systems Cisco Aironet Wireless Access Point AIRSAP2602EAK9 en pantalla completa, utiliza el botón Pantalla completa
  • Descargar al ordenador – también puedes descargar el manual de instrucciones de Cisco Systems Cisco Aironet Wireless Access Point AIRSAP2602EAK9 a tu ordenador y guardarlo en tu colección. Sin embargo, si no quieres ocupar espacio en tu dispositivo, siempre podrás descargarlo de ManualsBase.
Cisco Systems Cisco Aironet Wireless Access Point AIRSAP2602EAK9 Manual de instrucciones - Online PDF
Advertisement
« Page 1 of 38 »
Advertisement
Versión impresa

Muchas personas prefieren no leer el documento en la pantalla, sino en versión impresa. La opción de impresión también está prevista y puedes utilizarla haciendo clic en el enlace más arriba - Imprimir el manual. No tienes que imprimir el manual completo de Cisco Systems Cisco Aironet Wireless Access Point AIRSAP2602EAK9, solo las páginas que elijas. Ahorra papel.

Resúmenes

A continuación encontrarás resúmenes de los contenidos incluidos en las páginas posteriores del manual de instrucciones para Cisco Systems Cisco Aironet Wireless Access Point AIRSAP2602EAK9. Puedes utilizarlos si quieres ver rápidamente el contenido que se encuentra en la siguientes páginas del manual.

Resúmenes de contenidos
Resumen del contenido incluido en la página 1


GETTING STARTED GUIDE
Cisco Aironet 2600 Series Access Points
January, 2013
P/N: 78-20842-01
1 About this Guide
2 Introduction to the Access Point
3 Safety Instructions
4 Unpacking
5 Configurations
6 Access Point Ports and Connectors
7 Configuring the Access Point
8 Mounting the Access Point
9 Deploying the Access Point on the Wireless Network
10 Troubleshooting
11 Declarations of Conformity and Regulatory Information
12 Configuring DHCP Option 43 and DHCP Option 60
13 Access Point Specificat

Resumen del contenido incluido en la página 2

1 About this Guide This Guide provides instructions on how to install and configure your Cisco Aironet 2600 Series Access Point. The 2600 Series Access Point is referred to as the 2600 series or the access point in this document. 2 Introduction to the Access Point The 2600 series supports high-performing Spectrum Intelligence which sustains three spatial stream rates over a deployable distance with high reliability when serving clients. The 2600 series provides high reliability and overa

Resumen del contenido incluido en la página 3

– Management Frame Protection (MFP) (not available on autonomous or standalone models) – BandSelect (not available on autonomous or standalone models) – Throughput, forwarding, and filtering performance scaled to meet 3 spatial stream, 450 Mbps data-rates � 32 MB flash size � 802.11af/at – CDP (Cisco Discovery Protocol) � 2.4 GHz and 5 GHz 802.11n radios with the following features: – 3TX x 4RX – 3-spatial streams, 450 Mbps PHY rate – Spectrum intelligence – DPD (Digital Pre-Distortion) tech

Resumen del contenido incluido en la página 4

Warning Installation of the equipment must comply with local and national electrical codes. Statement 1074 Warning This product relies on the building’s installation for short-circuit (overcurrent) protection. Ensure that the protective device is rated not greater than: 20A. Statement 1005 Warning Do not operate your wireless network device near unshielded blasting caps or in an explosive environment unless the device has been modified to be especially qualified for such use. Statement 24

Resumen del contenido incluido en la página 5

4 Unpacking To unpack the access point, follow these steps: Step 1 Unpack and remove the access point and the accessory kit from the shipping box. Step 2 Return any packing material to the shipping container and save it for future use. Step 3 Verify that you have received the items listed below. If any item is missing or damaged, contact your Cisco representative or reseller for instructions. – The access point – Mounting bracket (selected when you ordered the access point) – Adjustable ceil

Resumen del contenido incluido en la página 6

These antennas are supported on the 2602E: Antenna Part Number Antenna Type Antenna Gain 2 GHz / 5 GHz (dBi) AIR-ANT2524DB-R Dual-resonant black dipole 2/4 AIR-ANT2524DW-R Dual-resonant white dipole 2/4 AIR-ANT2524DG-R Dual-resonant gray dipole 2/4 AIR-ANT2524V4C-R Dual-resonant, ceiling-mount omni 2/4 (4-pack) AIR-ANT2544V4M-R Dual-resonant omni (4-pack) 4/4 AIR-ANT2566P4W-R Dual-resonant Directional antenna 6/6 (4-pack) Internal Antennas The 2602I model access points are configured wi

Resumen del contenido incluido en la página 7

D D D D U U U U A A A A L L L L 6 Access Point Ports and Connectors The 2602E model access points have external antenna connectors and the LED indictor on the top of the model, as shown in Figure 1. The 2602I model access points have integrated antennas and do not have external connectors on the top of the unit; however, they do have the LED indicator on top of the unit, as shown in Figure 2. Figure 1 Access Point Ports and Connections (top) 1 2 A B D C 4 3 1 Antenna connector A 3 Antenna

Resumen del contenido incluido en la página 8

Figure 2 Access Point LED Indicator (top) 1 1 LED indicator The ports and connections on the bottom of the access point are shown in Figure 3. Figure 3 Access Point Ports and Connections (bottom) 1 5 6 6 2 3 4 8 272377

Resumen del contenido incluido en la página 9

1 Kensington lock slot 4 Console port DC Power connection Security padlock and hasp (padlock not 2 5 included) 3 Gbit Ethernet port 6 Mounting bracket pins (feet for desk or table-top mount) 7 Configuring the Access Point This section describes how to connect the access point to a wireless LAN controller. Because the configuration process takes place on the controller, see the Cisco Wireless LAN Controller Configuration Guide for additional information. This guide is available on Cisco.co

Resumen del contenido incluido en la página 10

Note You cannot edit or query any access point using the controller CLI if the name of the access point contains a space. Note Make sure that the controller is set to the current time. If the controller is set to a time that has already occurred, the access point might not join the controller because its certificate may not be valid for that time. Access points must be discovered by a controller before they can become an active part of the network. The access point supports these controlle

Resumen del contenido incluido en la página 11

Preparing the Access Point Before you mount and deploy your access point, we recommend that you perform a site survey (or use the site planning tool) to determine the best location to install your access point. You should have the following information about your wireless network available: � Access point locations. � Access point mounting options: below a suspended ceiling, on a flat horizontal surface, or on a desktop. Note You can mount the access point above a suspended ceiling but you m

Resumen del contenido incluido en la página 12

Performing a Pre-Installation Configuration The following procedures ensure that your access point installation and initial operation go as expected. A pre-installation configuration is also known as priming the access point. This procedure is optional. Note Performing a pre-installation configuration is an optional procedure. If your network controller is properly configured, you can install your access point in its final location and connect it to the network from there. See the “Deployi

Resumen del contenido incluido en la página 13

Step 1 Make sure that the Cisco wireless LAN controller DS port is connected to the network. Use the CLI, web-browser interface, or Cisco WCS procedures as described in the appropriate Cisco wireless LAN controller guide. a. Make sure that access points have Layer 3 connectivity to the Cisco wireless LAN controller Management and AP-Manager Interface. b. Configure the switch to which your access point is to attach. See the Cisco Unified Wireless Network WLAN Controller Guide: Cisco 440x Se

Resumen del contenido incluido en la página 14

Note The 2600 series access point requires a Gigibit Ethernet link to prevent the Ethernet port from becoming a bottleneck for traffic because wireless traffic speeds exceed transmit speeds of a 10/100 Ethernet port. b. As the access point attempts to connect to the controller, the LEDs cycle through a green, red, and amber sequence, which can take up to 5 minutes. Note If the access point remains in this mode for more than five minutes, the access point is unable to find the Master Cisco

Resumen del contenido incluido en la página 15

8 Mounting the Access Point Cisco Aironet 2600 series access points can be mounted in several configurations, including on a suspended ceiling, on a hard ceiling or wall, on an electrical or network box, and above a suspended ceiling. Click this URL to browse to complete access point mounting instructions: http://www.cisco.com/en/US/docs/wireless/access_point/mounting/guide/apmount.html 9 Deploying the Access Point on the Wireless Network After you have mounted the access point, follow the

Resumen del contenido incluido en la página 16

10 Troubleshooting If you experience difficulty getting your access point installed and running, look for a solution to your problem in this guide or in additional access point documentation. These, and other documents, are available on Cisco.com. Guidelines for Using Cisco Aironet Lightweight Access Points Keep these guidelines in mind when you use 2600 series lightweight access points: � The access point can only communicate with Cisco wireless LAN controllers, such as 2500 series, 5500

Resumen del contenido incluido en la página 17

Figure 5 Access Point LED Location 1 1 Status LED The access point status LED indicates various conditions and are described in Table 1. Table 1 LED Status Indications Message Status Message Type LED Meaning Boot loader status Blinking green DRAM memory test in progress sequence DRAM memory test OK Board initialization in progress Initializing FLASH file system FLASH memory test OK Initializing Ethernet Ethernet OK Starting Cisco IOS Initialization successful Association status Green Normal op

Resumen del contenido incluido en la página 18

Table 1 LED Status Indications (continued) Message Status Message Type LED Meaning Operating status Blinking blue Software upgrade in progress Cycling through green, Discovery/join process in progress red, and off Rapidly cycling Access point location command invoked through blue, green, and red Blinking red Ethernet link not operational Boot loader warnings Blinking blue Configuration recovery in progress (MODE button pushed for 2 to 3 seconds) Red Ethernet failure or image recovery (MODE

Resumen del contenido incluido en la página 19

Controller software enables you to configure the access points to send all CAPWAP-related errors to a syslog server. You do not need to enable any debug commands on the controller because all of the CAPWAP error messages can be viewed from the syslog server itself. The state of the access point is not maintained on the controller until it receives a CAPWAP join request from the access point. Therefore, it can be difficult to determine why the CAPWAP discovery request from a certain access

Resumen del contenido incluido en la página 20

� The access point is still connected to the same controller, and a specific syslog server IP address has been configured for the access point on the controller using the config ap syslog host specific Cisco_AP syslog_server_IP_address command. In this case, the controller sends the new specific syslog server IP address to the access point. � The access point is disconnected from the controller and joins another controller. In this case, the new controller sends its global syslog server IP


Manuales de instrucciones similares
# Manual de instrucciones Categoría Descargar
1 Cisco Systems 1040 Manual de instrucciones Tarjeta de red 7
2 Cisco Systems 10BASE-FL Manual de instrucciones Tarjeta de red 2
3 Cisco Systems 1105 Manual de instrucciones Tarjeta de red 1
4 Cisco Systems 15327 Manual de instrucciones Tarjeta de red 1
5 Cisco Systems 32369 Manual de instrucciones Tarjeta de red 1
6 Cisco Systems 3515 MCU12 Manual de instrucciones Tarjeta de red 1
7 Cisco Systems 3545 Serial Manual de instrucciones Tarjeta de red 0
8 Cisco Systems 3515 MCU24 Manual de instrucciones Tarjeta de red 0
9 Cisco Systems 3545 MCU Manual de instrucciones Tarjeta de red 0
10 Cisco Systems 3000 Manual de instrucciones Tarjeta de red 2
11 Cisco Systems 3500 Series Manual de instrucciones Tarjeta de red 1
12 Cisco Systems 2000 Manual de instrucciones Tarjeta de red 0
13 Cisco Systems 3545 PRI Manual de instrucciones Tarjeta de red 1
14 Cisco Systems 3522 BRI Manual de instrucciones Tarjeta de red 0
15 Cisco Systems 4490 Manual de instrucciones Tarjeta de red 0
16 Sony BTA-NW1A Manual de instrucciones Tarjeta de red 2
17 Sony BKMW-E3000 Manual de instrucciones Tarjeta de red 2
18 Sony AC-SQ950D Manual de instrucciones Tarjeta de red 0
19 Sony BBV RX100 Manual de instrucciones Tarjeta de red 3
20 Sony CLIE A-AVZ-100-11 Manual de instrucciones Tarjeta de red 1