Manual de instrucciones de Xantech 590-00

Resumen del contenido incluido en la página 1

Controllers
OUTPUT
DELETE
CONFIRM
PROGRAM
ERROR
INSTALLATION INSTRUCTIONS
590-00
PROGRAMMABLE CONTROLLER
590
PROGRAMMABLE CONTROLLER
Infrared Sensor
FRONT PANEL
The front panel of the 590 is made of acrylic plastic. It should be cleaned with a soft cloth as it scratches
easily. Behind the panel are five red LEDs and an infrared sensor.
RED LEDs
ERROR - Lights when an error occurs in the learning process or when trying to send an
unprogrammed command.
PROGRAM - Lights when the PGM (program) but

Resumen del contenido incluido en la página 2

SCREW TERMINALS Opto-Isolator Inputs - 16 pairs of positive and negative terminals, isolated from ground. O - Infrared Output - Positive terminal for the IR output signal. G - Ground - Negative terminal for the IR output signal. The "O" and "G" terminals drive IR emitters directly or the IR input of Xantech connecting blocks, IR routers, interface modules, etc. 12VDC - 12 volts output, positive & negative terminals. INPUTS A decision as to the type of external input(s) must be +12V DC made.

Resumen del contenido incluido en la página 3

Controllers 3. Press and hold down the key for the 590 input into which you wish to store the command. Remember, the "key" may be a contact closure push-button device, such as the Xantech 598 keypad (Fig. 1), or a simple jumper wire, one end connected to the"+" 12VDC terminal and the other end held temporarily onto the "+" terminal of the desired input. NOTE: In either case, you must have previously connected ground wires from each of the "–" terminals of the inputs you are using back to the "

Resumen del contenido incluido en la página 4

short tap for its command to be properly executed, then only a short burst of it should be stored in the 590. Step 4 would, therefore, be modified as follows: 4. Press the key on the remote controller that you wish to store. Hold the key for a very short period of time or only as long as you usually press it when controlling the audio/video equipment directly. The PROGRAM lamp will flicker while the information is being stored. SEQUENCE FUNCTION The 590 can also be programmed so that one or mor

Resumen del contenido incluido en la página 5

Controllers A sequence is completed. You may now test it by pressing the ON/OFF key (bank 1). It should now send the three commands to turn the AM/FM receiver ON, turn the VCR ON and select the VCR Input on the receiver, in that order. USING THE 590 PROGRAMMABLE CONTROLLER WITH NON- MOMENTARY INPUTS The Model 590 was designed to be used with momentary contact switches. In such applications, a button is pressed, the 590 generates an IR command, and the button is released. If the button is not

Resumen del contenido incluido en la página 6

• By plugging the Model 781C-00 power supply into the switched AC outlet on the back of a stereo receiver, a constant 12V DC is applied to the 599. The 599 generates a short pulse (+12V, 100 mSec) at its ON terminal when it first sees +5 to +30V DC at its IN+ and IN– terminals (the stereo receiver is turned on). • Similarly, it will generate a short pulse at its OFF terminal (+12V, 100 mSec) when the +5 to +30 volts drops to 0 volts (the stereo receiver is turned off). • This short pulse opera

Resumen del contenido incluido en la página 7

Controllers INSTALLATION INSTRUCTIONS 590-00 DOOR CHIME ACTIVATED SYSTEM The circuit below, Fig. 1, shows a simple means of using a door chime or door bell to activate one of the inputs on a Xantech Model 590 Programmable Controller, to initiate a system function or functions. Functions that may be initiated by this system, might include the following: • Switch the AV system source selector to a front door surveillance camera. • Turn on front door intercom. • Mute the audio in an A/V system. Rec

Resumen del contenido incluido en la página 8

 134