Resumen del contenido incluido en la página 1
M34519T-MCU
MCU Board for 4500 Series 4518, 4519, 4583 and 4584 Group MCUs
User's Manual
Rev.2.00
July 1, 2004
REJ10J0071-0200Z
Resumen del contenido incluido en la página 2
* IBM and PC/AT are registered trademarks of International Business Machines Corporation. * NQPACK, YQPACK, YQSOCKET, YQ-Guide, HQPACK, TQPACK and TQSOCKET are trademarks of Tokyo Eletech Corporation. Keep safety first in your circuit designs! • Renesas Technology Corporation and Renesas Solutions Corporation put the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lea
Resumen del contenido incluido en la página 3
Preface This user's manual describes the specifications of MCU board M34519T-MCU for the Renesas 4518, 4519, 4583 and 4584 Groups of 4-bit CMOS single-chip MCUs. The M34519T-MCU is an MCU board for the PC4504 emulator. For emulator main unit PC4504 and emulator debugger M3T-PD45, refer to each user's manual (online manual). To use the product properly Precautions for Safety • In both this user's manual and on the product itself, several icons are used to insure proper handling of this product an
Resumen del contenido incluido en la página 4
Contents Chapter 1. Precautions for Safety ...........................................................................................5 1.1 Safety Symbols and Meanings ..............................................................................5 Chapter 2. Package Contents ..................................................................................................9 2.1 Contents of the M34519T-MCU ...........................................................................9 2.2 Other Neces
Resumen del contenido incluido en la página 5
Chapter 1. Precautions for Safety Both in the M34519T-MCU user's manual and on the product, several icons are used to insure proper handling of this product and also to prevent injuries to you or other persons, or damage to your properties. This chapter describes precautions which should be taken in order to use the M34519T-MCU safely and properly. Be sure to read this chapter before using this product. 1.1 Safety Symbols and Meanings If the requirements shown in the "WARNING" sentences are igno
Resumen del contenido incluido en la página 6
WARNING Warning for Installation: • Do not set this product in water or areas of high humidity. Spilling water or some other liquid into the main unit can cause an unrepairable damage. Warning for Use Environment: • This equipment is to be used in an environment with a maximum ambient temperature of 35°C. Care should be taken that this temperature is not exceeded. CAUTION Cautions to Be Taken for This Product: • Do not disassemble or modify this product. Disassembling or modifying this product c
Resumen del contenido incluido en la página 7
IMPORTANT Notes on Connecting the Target System: • When connecting the target system, be sure to shut off the power of the emulator and the target system. • Connect the emulator probe carefully. • When connecting the emulator probe, use care not to twist the cable. An excessive twist may cause breaking of the wire. Note on MCU board Installation: • Before installing and removing the MCU board, always be sure to power off the PC4504 emulator main unit and unplug its power cord from the outlet. No
Resumen del contenido incluido en la página 8
MEMO ( 8 / 36 )
Resumen del contenido incluido en la página 9
Chapter 2. Package Contents 2.1 Contents of the M34519T-MCU Table 2.1 shows the contents of the M34519T-MCU package. When unpacking it, check to see that all of these components are included. Table 2.1 Contents of the M34519T-MCU package Item Product name Quantity 1 M34519T-MCU 1 2 M34584MD-001FP (for replacement) 1 3 M4584 monitor ROM for the 4583 and 4584 Groups (for replacement) 1 4 100-wire half-pitch cable (40 cm) 1 5 50-wire normal-pitch cable (10 cm) 1 6 2-wire external trigger cable (50
Resumen del contenido incluido en la página 10
2.2 Other Necessary Products To bring forward your program development with the 4518, 4519, 4583 and 4584 Groups of 4-bit MCUs, the products listed in Table 2.2 are necessary in addition to those contained in the package. Get them separately when necessary. Table 2.2 Other products required for developing the 4518, 4519, 4583 and 4584 Group MCUs Product Product type name PC4504 Emulator main unit M3T-PD45 Emulator debugger PCA7441 (for 4519 and 4584) PCA7442FPG02 (for 4518 and 4583 LQFP) Program
Resumen del contenido incluido en la página 11
Chapter 3. M34519T-MCU 3.1 Outline With emulator main unit PC4504, the M34519T-MCU can make up an emulator system which can be operated by a host machine. Figure 3.1 shows an emulator system configuration. For details on how to connect the target system, refer to "3.6 Connection to the Target System" (page 18). CPU board PC4500E Control board PCA4504A + PCA4504B Emulator debugger M3T-PD45 Function expansion board PCA4504R + PCA4504B CD-ROM For 32-pin LQFP MCU board M34519T-MCU RS-232C Host machi
Resumen del contenido incluido en la página 12
3.2 Specifications Table 3.1 lists specifications of the M34519T-MCU. Table 3.1 M34519T-MCU specifications Emulator PC4504 Emulator 1 1 Applicable MCUs 4518 Group, 4519 Group, 4583 Group* , 4584 Group* Evaluation MCU 4518, 4519 Groups M34519M8-001FP (preinstalled) 4583, 4584 Groups M34584MD-001FP (included) Monitor program 4518, 4519 Groups M4519 (preinstalled) 4583, 4584 Groups M4584 (included) Clock Main clock: 6.0 MHz (OSC-2 [6.0 MHz mounted]) Divide-by-8 mode (f(XIN)/8) Divide-by-4 mode (f(X
Resumen del contenido incluido en la página 13
3.3 Switches Table 3.2 shows the functions of the switches and their factory-settings. Table 3.2 Functions of the switches Switch Label Switch position Description Factory-setting Does not output VDD from the OFF ON OFF M34519T-MCU to the target system. SW1 Outputs VDD from the M34519T-MCU OFF ON OFF ON to the target system. Set the MCU's ROM size. • Set "2" for M2 • Set "4" for M4 SW2 ROMSIZE • Set "6" for M6 • Set "8" for E8, M8 8 • Set "D" for ED, MD Operates the evaluation MCU on the 3 V 5 V
Resumen del contenido incluido en la página 14
3.4 Check Pins Table 3.3 lists the check pins of the M34519T-MCU, and Figure 3.3 shows their positions. Table 3.3 Check pins Function Pin TP1 VDD Outputs +3 V or +5 V (MCU voltage) according to the setting of SW3. TP2 XIN Outputs a system clock input to the evaluation MCU. TP3 GND Ground RUN/STOP TP4 Held low when a user program is executed, held high when it is stopped. TP5 WRST Held high when WRST instruction is executed, and you can check the initialization cycle of the watchdog timer by obse
Resumen del contenido incluido en la página 15
(1) Connector J3 Table 3.5 lists the pin assignments of the 100-wire half-pitch connector J3 for connecting the PCA4029. And Figure 3.4 shows the pin layout of connector J3. Table 3.5 Pin assignments of connector J3 Line A Line B Line C Line D Pin No. Signal I/O Pin No. Signal I/O Pin No. Signal I/O Pin No. Signal I/O 1 GND 1 GND 1 P13 I/O 1 P12 I/O 2 GND 2 GND 2 D0 I/O 2 P11 I/O 3 GND 3 GND 3 D1 I/O 3 P10 I/O 4 GND 4 GND 4 D2 I/O 4 P03 I/O 5 GND 5 GND 5 D3 I/O 5 P02 I/O 6 GND 6 GND 6 D4 I/O 6 P
Resumen del contenido incluido en la página 16
Some signals which are connected to the target system are emulated by the M34519T-MCU. Table 3.6 lists the connections of the target system and each pin. Table 3.6 Connection of the target system and each pin Signal Item 4519 Group 4584 Group • P20/SCK • P20--P23 • P21/SOUT • P30/INT0, P31/INT1 • P22/SIN • P40--P43 • P30/INT0, P31/INT1 • P50--P53 • P32, P33 • P60/AIN0, P61/AIN1 Pins connected directly to the target system • P40/AIN4--P43/AIN7 • P62, P63 (12 types 23 pins) • P50--P53 • D6/CNTR0 •
Resumen del contenido incluido en la página 17
(3) Connector J6 Connector J6 is a connector used to connect oscillator circuit board OSC-2. Table 3.8 lists the pin assignments of connector J6. Figure 3.5 shows the pin layout of connector J6. Figure 3.6 shows a connection diagram of oscillator circuit board OSC-2 (6.0 MHz). Table 3.8 Pin assignments of connector J6 Pin No. Signal Function 1 VCC Power supply 2 GND GND 3 CLK Clock input 4 GND GND Figure 3.5 Pin layout of connector J6 Figure 3.6 Connection diagram of the oscillator circuit CAUTI
Resumen del contenido incluido en la página 18
3.6 Connection to the Target System Connections of the M34519T-MCU and target systems are shown in Figure 3.7 below. 50-wire normal-pitch cable M34513T-PTCA M34513T-PTCA M34513T-PTCB M34513T-PTCC TQPACK032SA FFC-50BSM1 ME-2-1 (1) Connection to 2.54-mm-pitch (2) Connection to IC socket (3) Connection to 32-pin LQFP 50-pole dual-in-line pin for 32-pin SDIP foot pattern Figure 3.7 Connections to target systems ( 18 / 36 )
Resumen del contenido incluido en la página 19
(1) Connection to 2.54-mm-pitch 50-pole dual-in-line pins (for 42-pin SSOP) Connect this product to 50-pole dual-in-line pins using the included 50-wire normal-pitch cable. Use the following products: (1) 100-wire half-pitch cable (40 cm) (2) Pitch converter board PCA4029 (3) 50-wire normal-pitch cable (10 cm) Table 3.9 lists the connector assignments of the 50-wire normal-pitch cable, and Figure 3.8 shows the pin layout of the 50-wire normal-pitch cable. Be careful not to connect the cable in a
Resumen del contenido incluido en la página 20
(2) Connection to the IC socket for 32-pin SDIP Attach pitch converter board M34513T-PTCA to the 50-wire normal-pitch cable, and connect it to an IC socket for 32-pin SDIP on the target system. Use the following products: (1) 100-wire half-pitch cable (40 cm) (2) Pitch converter board PCA4029 (3) 50-wire normal-pitch cable (10 cm) (4) Pitch converter board M34513T-PTCA Table 3.10 lists the connector assignments of pitch converter board M34513T-PTCA. When attaching the pitch converter board, chec