Resumen del contenido incluido en la página 1
STATUS 1 2 3 4 5 6 7 8
MPEG2 Encoder WJ-GXE900 900
MPEG2 Decoder WJ-GXD900 900
MPEG2 Decoder WJ-GXD900 900
OPERATE
LINK1 100 1000 ACT
OPERATE
ACT
LINK1 100 1000
OPERATE
STATUS 1 2 3 4 5 6 7 8
STATUS 1 2 3 4 5 6 7 8
MPEG2 Encoder
Model No. WJ-GXE900
MPEG2 Decoder
Model No. WJ-GXD900
Operating Instructions
WJ-GX
Resumen del contenido incluido en la página 2
ENGLISH VERSION Caution: Before attempting to connect or operate this product, please read the label on the bottom. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN For U.S.A NOTE: This equipment has been tested and found to CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to DO NOT REMOVE COVER (OR BACK). provide reasonable protection against harmful interference NO USER-SERVICEABLE PART
Resumen del contenido incluido en la página 3
IMPORTANT SAFETY INSTRUCTIONS 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions. 8) Do not use near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarize
Resumen del contenido incluido en la página 4
CONTENTS CONTENTS IMPORTANT SAFETY INSTRUCTIONS ...........................................................................3 CONTENTS........................................................................................................................4 FEATURES ........................................................................................................................6 PRECAUTIONS ......................................................................................................
Resumen del contenido incluido en la página 5
HOW TO USE THE CGI COMMANDS ............................................................................85 CAMERA CONTROL .................................................................................................86 CAMERA SETTINGS MENUS CONTROL ................................................................88 SWITCHING STREAMING VIDEO ............................................................................90 CONTROLLING START / STOP OF THE ENCODER ....................................
Resumen del contenido incluido en la página 6
FEATURES The MPEG2 Image Delivery System delivers image data as streaming data to a network such as a LAN. This system consists of the encoder that converts an analog video signal (NTSC) to the digital data (MPEG2), and the decoder that converts the digital data (MPEG2) to the analog video signal (NTSC). • This system features the MPEG2 compression scheme. It is possible to send and receive motion pictures at 30 fps, up to 9 Mbps. • This system can be connected with a network that supports TCP
Resumen del contenido incluido en la página 7
PRECAUTIONS ● Refer all work related to the installation of ● Do not use strong or abrasive detergents these products to qualified service per- when cleaning the appliance body. sonnel or system installers. Use a dry cloth to clean the appliance when it is dirty. When the dirt is hard to remove, use a mild detergent ● Do not operate the appliances beyond and wipe gently. their specified temperature, humidity, or power source ratings. ● Network with surge protector Use the appliance at temperatur
Resumen del contenido incluido en la página 8
PRECAUTIONS SYSTEM REQUIREMENTS Setting up and operating the encoder and the decoder with a web browser, and execution of the "Panasonic IP Setup" software are possible with PCs meeting the system requirements described below. ® ® OS Microsoft Windows 98 Second Edition ® ® Microsoft Windows 2000 Professional Service Pack 3 ® ® Microsoft Windows Millennium Edition ® ® Microsoft Windows XP ® ® Microsoft Windows NT Workstation 4.0 Service Pack 6a Computer PC/AT Compatible ® ® CPU Intel Pentium II (
Resumen del contenido incluido en la página 9
TRADEMARKS AND REGISTERED TRADEMARKS • Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation in the U.S. and/or other countries. • Intel and Pentium are trademarks of Intel Corporation. • Ethernet is a registered trademark of Xerox Corporation. • Adobe, Adobe logos, and Acrobat are registered trademarks of Adobe Systems Incorporated in the U.S. and/ or other countries. • Dolby Digital is a registered trademark of Dolby Laboratories. • Other names of companies and p
Resumen del contenido incluido en la página 10
MAJOR OPERA MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS TING CONTROLS AND THEIR FUNCTIONS MPEG2 Encoder Front Panel STATUS 1 2 3 4 5 6 7 8 STATUS 1 2 3 4 5 6 7 8 OPERATE OPERATE AB C ON WJ-GXE900 SW1 SW2 RESET MPEG2 Encoder WJ-GXE900 BLINKING TEMPERATURE WARNING BLINKING TEMPERATURE WARNING ert q w STATUS 6 (LINK2): This indicator lights up when the q Power Indicator (OPERATE) initialization of the software has been completed This indicator lights up when the power of the correctly, and the en
Resumen del contenido incluido en la página 11
DIP1: Normally, select OFF. When ON is selected, the firmware, as the start up program (loaded at the factory), starts up. The value of the settings will not be deleted. DIP2: When ON is selected, the IP address and all the current settings will return to the default settings. DIP3: When ON is selected, the initialization of the IP address will start. (The initialization of the IP address starts only when the DIP4 is set to OFF.) DIP4: When ON is selected, DHCP will be available. DIP5: Normally,
Resumen del contenido incluido en la página 12
MAJOR OPERA MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS TING CONTROLS AND THEIR FUNCTIONS MPEG2 Encoder Rear Panel e Trigger Output Terminal (TRIGGER OUT 1 - 4, G (GND)) qwert y u The trigger output signal (Open collector output, 25 V DC, 50 mA max.) will be supplied from this terminal TRIGGER OUT ALARM IN RESET ON OFF using the contact output controlling CGI commands. POWER 100BASE-TX TERM RS-485 4321G4321GGV + – G ON OFF 4 3 2 1 (Refer to the operating instructions (pdf file) included VIDEO
Resumen del contenido incluido en la página 13
!0 Audio Input Connector (AUDIO IN 1 - 4) !1 Signal Ground Terminal (SIGNAL GND) (–10 dB, 9-pin D-sub) Up to 4 audio devices can be connected. To connect !2 Power Cord audio devices, a cable (WV-CA64, not supplied) is Connect to an AC outlet (120V AC, 60 Hz). required. MPEG2 Decoder Front Panel we LINK1 100 1000 ACT STATUS 1 2 3 4 5 6 7 8 OPERATE MPEG2 Decoder WJ-GXD900 BLINKING TEMPERATURE WARNING q 1 2 3 4 5 6 7 8 LINK1 100 1000 ACT STATUS OPERATE AB C ON WJ-GXD900 SW1 SW2 RESET BLINKING TEMPE
Resumen del contenido incluido en la página 14
MAJOR OPERA MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS TING CONTROLS AND THEIR FUNCTIONS will light up when decoding streaming data to Note: The Main CPU mode is the advanced function video signals. The indicators will blink when the for integrated control. Use these switches with decoder is not receiving streaming data. The the default settings for normal use. indicators will go off when decoding has stopped. DIP6: Reserved STATUS 5 (RUN): This indicator lights up when the DIP7: When ON is se
Resumen del contenido incluido en la página 15
MPEG2 Decoder Rear Panel qe w rtyu 2 1 2 1 ON 1000BASE-T/ MIX QUAD SIGNAL GND 100BASE-TX RESET V+ – G 4 3 4 3 OFF i AUDIO OUT VIDEO OUT POWER q Ethernet Port (100BASE-TX/1000BASE-T) QUAD: Connect a video display device such as a (RJ-45) monitor. 4-images (VIDEO OUT 1 - 4) can be Connect with a network device such as router or hub displayed simultaneously in a monitor. using an Ethernet cable. Depending on the transmission speed between a device and the t Cooling Fan decoder, use the proper cable
Resumen del contenido incluido en la página 16
CONNECTIONS CONNECTIONS Multicast Transmission The multicast transmission will be suitable for the following systems. • When the number of cameras is more than the number of monitors in a system, and switching streaming video to be displayed on the monitors using the decoder • When monitoring pictures of a camera on two or more monitors When the number of cameras is more than number of monitors in the system, and when desig- nating camera channels to be displayed on monitors using a PC Use the C
Resumen del contenido incluido en la página 17
When monitoring pictures of a camera with two or more monitors Use the CGI command to designate pictures of the camera to be displayed on the monitors. Send the CGI command to each decoder and set the receiving IP address of the camera whose pictures are to be displayed on the monitors. Refer to the "SWITCHING STREAMING VIDEO" section of "HOW TO USE THE CGI COMMANDS" on page 90. Camera 1 VIDEO IN 1 STATUS 1 2 3 4 5 6 7 8 10BASE-T/ OPERATE MPEG2 Encoder MPEG2 Encoder WJ-GXE900 100BASE-TX 100BASE
Resumen del contenido incluido en la página 18
CONNECTIONS CONNECTIONS System Example (Switching streaming video) This is a system example with 8 cameras and 4 monitors, and switching streaming video using a PC. Refer to the "SWITCHING STREAMING VIDEO" section of "HOW TO USE THE CGI COMMANDS" on page 90 about the CGI command to switch streaming video. Note: All the "DESTINATION PORT No." of each encoder should be the same. The IP addresses to be assigned for "DESTINATION IP ADDRESS" should be different according to the respective VIDEO IN co
Resumen del contenido incluido en la página 19
Operation Example (Switching streaming video) These are examples to operate the systems introduced on the previous pages. Switching currently monitored streaming video to another streaming video Use the following CGI commands. http://(IP address of the decoder to be controlled)/control4?decode=start&ch=xx&address=aaa.aaa.aaa.aaa:ppppp control4?: Definition to control streaming video (required) decode =start: Identifier to start decoding (required) ch=xx: Number of the VIDEO OUT connector of th
Resumen del contenido incluido en la página 20
CONNECTIONS CONNECTIONS System example (Recording streaming video) This is a system example to control the digital disk recorder (WJ-HD500) from a PC. VIDEO IN 12 3412341234 12 3 4 MPEG2 MPEG2 MPEG2 MPEG2 STATUS 1 2 3 4 5 6 7 8 STATUS 1 2 3 4 5 6 7 8 STATUS 1 2 3 4 5 6 78 STATUS 1 2 3 4 5 6 78 OPERATE OPERATE OPERATE OPERATE Encoder MPEG2 Encoder WJ-GXE900 Encoder MPEG2 Encoder WJ-GXE900 Encoder MPEG2 Encoder WJ-GXE900 Encoder MPEG2 Encoder WJ-GXE900 Video output WV-CA64 WV-CA64 WV-CA64 (D-S
