Resumen del contenido incluido en la página 1
IP Power 9212
User Manual
Resumen del contenido incluido en la página 2
IP POWER 9212 USER MANUAL USER MANUAL IP POWER 9212 Version: X.X 2005.07 VER. X.X, - 1 -
Resumen del contenido incluido en la página 3
Warning: any changes to this equipment without permission may cause damages to your equipment! This equipment has been proved to can be prevented from the influence of harmful electronic jamming in normal business use condition. IMPORTANT NOTICE 1. IP POWER 9212 is deigned to be used in-door, we have no responsibility for the possible damage in out-door use especially in the rain. . 2. Please use the power adaptor provided by the dealer, we have no responsibility for the possible d
Resumen del contenido incluido en la página 4
IP POWER 9212 USER MANUAL Table of Content 1. INTRODUCTION..................................................................................................................... 4 FEATURES....................................................................................................................................... 2.BEFORE YOU START..........................................................
Resumen del contenido incluido en la página 5
1. Introduction The IP Power 9212 is a Network Controller & Sensor with 8 DI & 8 DO. A specific PC or software is not needed; you can easily control devices remotely and check the device status via the Internet anywhere in the world. Using a Browser such as Internet Explore or Netscape, you can securely access the unit. It includes 8 Digital Inputs, 8 Digital Relay Outputs and works like an IO Server. You can integrate it with Home / Office security, Personal entertainment, and Industri
Resumen del contenido incluido en la página 6
IP POWER 9212 USER MANUAL 2. Before you start 9212 package contents One set of IP POWER 9212 Main Board : 9200 Sensor board :9201 Pro Control Board : 9202 Pro One network wire with RJ45 port One 1A, 110~220V adaptor One D-Sub 15 Pin cable One install disc One rapid install manual Minimum System Requirements Minimum Inte
Resumen del contenido incluido en la página 7
3. Interface Description IP Power 9212 has three devices , 9200 is the network module, and the followed picture shows its interface: 9202 is the output module and figure below shows its interface: 9202 is the output module and figure below shows its interface: - 6 -
Resumen del contenido incluido en la página 8
IP POWER 9212 USER MANUAL 4. Hardware & Software installation Before you star to use IP Power 9212, please follow the steps below: Check the package to make sure the contents is complete. Prepare one Ethernet HUB, or Router Check the voltage of the power supply to make sure it is AC 110-240 volt Hardware Installation : Connect RJ45 first then POWER jack 1 Connect the 9200 to HUB thr
Resumen del contenido incluido en la página 9
NOTE: Because of the polarity protective function, it won’t damage the product if you reverse the polarity in installation. But it will cause the product cannot work properly 2. Source mode ( Voltage signal ) -- IN1 & IN4: can be connected to voltage signal detectors such as smoke detector, light detector and gas detector. 3. Sink mode ( Resistance signal ) —IN5 & IN8: can be connected to magnetic reed switch as the follow figures It can be installed in th
Resumen del contenido incluido en la página 10
IP POWER 9212 USER MANUAL Source mode ( Voltage input) : IN1-IN4 contacts are active signal sensor. If the voltage difference between the two contacts in one set within 0V~3V, 9212 shows ON. It the voltage difference within 4V~24V, 9212 shows OFF. So user can detect the change of equipment. Such as smoke detector, light detector and gas detector. NOTE: 1. The data in this figure is the ave
Resumen del contenido incluido en la página 11
Step 1 Cut off the live wire. Use a test pencil or screwdriver with voltage tester to identify the live wire between the two wires of electrical wire. NOTICE: this method must cut off the electrical wire of the household appliance. Please make the decision after reading method 5-2 and 5-3. Step 2: Use a test pencil or screwdriver with voltage tester to identify the live wire between the two wires of electrical wire. Cut off the live wire and connect to the port of IP
Resumen del contenido incluido en la página 12
IP POWER 9212 USER MANUAL 3. You an control multi power by use the power extension cord NOTICE: Do not connect too much energy intensive electrical equipment such as air conditioner, electrical heater, microwave over or over in the same electrical outlet. Too much electrical currency may cause fire. This product not guaranties the possible damage because of too muc
Resumen del contenido incluido en la página 13
2. All the IP 92XX series, IP Kamera 9000 series/ IP Video 9100 series in the same subnet of the Ethernet will be found and be display in the window by the software. The default name of IP Sensor 9212 is IP POWER. IPEditV3 can adjust Name / Gateway / IP / Netmask / HTTP Port1) 2- 1 : Change Name : MAXIMUM 10 DIGIT 2-2 : After Change Gateway , IP, Netmask (xxx.xxx.xxx.0 ~ xxx.xxx.xxx.254) or Port1(1~32767) , the device will tu
Resumen del contenido incluido en la página 14
IP POWER 9212 USER MANUAL 3. If can not get in the 92XX web page , please set the segment of IP 9060(A) to be same as your PC. * You can get your PC network information – IP Addres, Subnet Mask and Default Gateway by step: start execute key “cmd” in dialog key “ipconfig” in MS-DOS mode The last digit of IP address can be any number between 1~
Resumen del contenido incluido en la página 15
6. Control and settings through the Internet Type the new IP address of IP Power 9212 in the address field and you can enter the login web page. Input the default password 12345678(you can change the password as you wish), click the OK and then you can enter the Web Control page. 1)Maximum 8 digit for Password Sensor of IP Power 9212 : Read IO Source mode ( Voltage input) : IN1-IN4 contacts are active signal sensor. If the voltage difference be
Resumen del contenido incluido en la página 16
IP POWER 9212 USER MANUAL IN5-IN8 contacts are short circuit sensor. If the resistance between the two contacts in one set within 0 Ω~200 Ω, 9212 shows ON. If the resistance within 500 Ω~ ∞, 9212 shows OFF. So user can detect the movement of equipment through the magnetic reed switch or other kind of reactive sensors. NOTE: 1. The data in this figure is the average measure value. To ensure the
Resumen del contenido incluido en la página 17
Click the test-itself button and you will see the figure above. The states of OUT1, OUT2, OUT3 and OUT4 will separately keep in ON for 1 second, 3 seconds, 6 seconds and 8 seconds, then all back to OFF. After one period, four outputs will keep in OFF state for the same time. This process will repeat until you click the reset or cancel button. 2. Set the output’s state to ON/OFF Click the output you want to change, set it to ON or OFF state and click apply button to finish the s
Resumen del contenido incluido en la página 18
IP POWER 9212 USER MANUAL Setting the password for IP Power 9212 Click the change password option at the left window and you can enter the change password page. Follow the instructions, fill in the old password and new password, then click the apply button to confirm. Setting the IP address for IP Power 9212 1. Setting a fixed IP address for IP Power 9212. Click the setup o
Resumen del contenido incluido en la página 19
5) When setup the setting please confirm the IP Address & Controlled IP Address is same address. Special Hardware Inter-Control - 92XX series : Use 9201 / 9212 ( DI part) to control ( IP Power 9212 & 9202 / IP Sensor 9201 / IP Motor 9203 ) 1. 92XX series Inter-Control function : Use DI (Digital Input ) sensor device as main controller ( Like 9212 or 9201 ) to controlled device B ( like 9212 / 9202 / 9203) Correspondence connectors : Ma
Resumen del contenido incluido en la página 20
IP POWER 9212 USER MANUAL B. Light : This device can control 9202 / 9212 (IP Power) - by change the default setting of : Normal close or normal open C. Motor : This device can control 9203(IP Motor) –control the direction of turning.. 3. Controlled IP Address: Setting the Ip Address of controlled device . In Inter - control mode when transfer , . the Out Light(P6.1/P6.2) wi
