Resumen del contenido incluido en la página 15
6 Maintaining and Troubleshooting Your E-3200 System
Resumen del contenido incluido en la página 16
System Components Contents System board ........................................................... 8 Riser card ............................................................... 10 I/O connectors........................................................ 12 Removing the System Board ................................ 13 Replacing the Processor ........................................ 16 Setting the Jumpers................................................ 20 Installing Memory and Hardware...............
Resumen del contenido incluido en la página 17
System board System board components are identified in the following figure and list. A I H B G F E D C A Back panel I/O connectors B Configuration jumper (J5G1) C Battery D Onboard speaker E Slot 1 processor connector F Fan (active heat sink) connector 8 Maintaining and Troubleshooting Your E-3200 System
Resumen del contenido incluido en la página 18
G DIMM slots H Digital Versatile Disc (DVD) connector I AGP connector System Components 9
Resumen del contenido incluido en la página 19
Riser card The riser card is mounted to the chassis by brackets at its base and two screws at the top. The two screws attach the riser card to a bracket attached to the power supply cage. To enable easy removal of the system board without unplugging cables or connectors, the riser card contains most of the connectors (including the integrated RJ-45 Network interface connector) and slots used by the internal system components. Back of riser card Primary IDE controller Secondary IDE controlle
Resumen del contenido incluido en la página 20
A ATX power connector B SCSI LED connector C JP10: CPU/Chassis Fan connector D Front panel control connector E NLX system board edge connector F PCI/ISA slot (shared) G PCI slots (2) H SW1: Chassis intrusion switch I CN3: TAD/Speakerphone J CN4: CD/DVD audio connector K JP9: Power supply fan connector L JP7: Wake on LAN connector M JP8: Ring in connector System Components 11
Resumen del contenido incluido en la página 1
Maintaining and
Troubleshooting
Your E-3200
System
MAN US E3200 TECH REF R0 7/98
8502684
Resumen del contenido incluido en la página 2
Maintaining and Troubleshooting Your E-3200 System Part #8502684 MAN US E3200 TECH REF R0 7/98 In our effort to use nature’s resources efficiently and wisely, we print all manuals on recycled papers that meet the minimum requirements established by the Federal EPA in its guidelines for recycled paper products.
Resumen del contenido incluido en la página 3
Notices Copyright © 1998 Gateway 2000, Inc. All Rights Reserved 610 Gateway Drive N. Sioux City, SD 57049 USA All Rights Reserved This publication is protected by copyright and all rights are reserved. No part of it may be reproduced or transmitted by any means or in any form, without prior consent in writing from Gateway 2000. The information in this manual has been carefully checked and is believed to be accurate. However, changes are made periodically. These changes are incorporated in ne
Resumen del contenido incluido en la página 4
Contents Preface ..................................................................................... iii Conventions Used in This Guide........................................................... iv Safety Instructions................................................................................... v Case Access ............................................................................ 1 Static Electricity Precautions .................................................................. 2 Open
Resumen del contenido incluido en la página 5
BIOS Setup Utility ...................................................................43 Using the Setup Utility.......................................................................... 44 Updating the BIOS................................................................................ 46 Troubleshooting ......................................................................49 Introduction........................................................................................... 50 Troubleshooti
Resumen del contenido incluido en la página 6
Preface Contents Conventions Used in This Guide ........................... iv Safety Instructions................................................... v
Resumen del contenido incluido en la página 7
Conventions Used in This Guide Throughout this guide, you will see the following conventions: Convention Description Enter Keyboard names are printed in small capitals. Ctrl+Alt+Del A plus sign indicates that the keys must be pressed simultaneously. Setup Commands to be entered, options to select, and messages that appear on your monitor are printed in bold. User’s Guide Names of publications and files are printed in italic. An important note informs you of special Important! circumstance
Resumen del contenido incluido en la página 8
Safety Instructions Warning! Observe the following safety instructions when using your system: Do not attempt to service • Follow all instructions marked on this product and in the the system yourself except as explained elsewhere in documentation. the system documentation. Adjust only those controls • When the system is turned off, a small amount of electrical current covered in the instructions. still runs through the system. Always unplug the system from the electrical outlet before
Resumen del contenido incluido en la página 9
• There is a danger of explosion if the complementary metal-oxide semiconductor (CMOS) battery is replaced incorrectly. Replace the battery with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions. Unplug the system from the wall outlet and refer servicing to • qualified personnel if: The power cord or plug is damaged. • • The power cord or plug is damaged. • Liquid has been spilled into the system. • The system
Resumen del contenido incluido en la página 10
Case Access Contents Static Electricity Precautions .................................. 2 Opening the Case..................................................... 3 Closing the Case ...................................................... 5
Resumen del contenido incluido en la página 11
Static Electricity Precautions Static electricity can permanently damage electronic components in your computer. When opening your computer case, always perform the following procedure: Caution! To prevent electrostatic 1. Wear a grounding wrist strap (available at most electronics stores). damage to your system, follow static electricity 2. Turn off the system power. precautions every time you open your computer case. 3. Touch the back of the power supply fan, located on the back of the
Resumen del contenido incluido en la página 12
Opening the Case Important! Only qualified personnel To perform work in the internal components of the computer, you must should open the system for open the case, which has two removable parts: maintenance. You need a grounding wrist strap and • A chassis cover, that surrounds the sides and top of the system the proper tools to remove the computer’s cover. • A front faceplate (bezel) that covers the front of the system Because the components inside your computer are extremely sensitive
Resumen del contenido incluido en la página 13
4. Lift up the rear of the cover and slide the cover toward the rear of the computer until the lip on the cover is free of the front bezel. Remove the cover. Side view To remove the front bezel 1. Lift the three upper tabs and push them through the slots in the chassis. The top of the bezel unlatches out and away from the chassis. 2. Lift the front of the chassis until the lower bezel tabs clear the chassis locking holes. Remove the bezel. 4 Maintaining and Troubleshooting Your E-3200 Sy
Resumen del contenido incluido en la página 14
Closing the Case Replace the cover as soon as you finish installing or removing components so that dust and dirt (which could damage the computer) do not collect inside the computer. To replace the front bezel 1. Lift the front of the chassis and set the lower chassis tabs into the locking holes on the bezel. 2. Press the bezel into the chassis until the three upper tabs snap into their locking holes. Two of the three upper tabs latch underneath the locking holes. One tab latches over the t
