Manual de instrucciones de AMX Enhanced Master RS-232 Controller AXB-EM232

Resumen del contenido incluido en la página 1

instruction manual
AXB-EM232
Enhanced Master RS-232 Controller
Axcess Central Controllers

Resumen del contenido incluido en la página 2

AMX Limited Warranty and Disclaimer AMX Corporation warrants its products to be free of defects in material and workmanship under normal use for three (3) years from the date of purchase from AMX Corporation, with the following exceptions: • Electroluminescent and LCD Control Panels are warranted for three (3) years, except for the display and touch overlay components that are warranted for a period of one (1) year.  Disk drive mechanisms, pan/tilt heads, power supplies, MX Series products, a

Resumen del contenido incluido en la página 3

Table of Contents Table of Contents Product Information .................................................................................................1 Product Information........................................................................................................... 1 Specifications .................................................................................................................... 2 Installation .....................................................................

Resumen del contenido incluido en la página 4

Table of Contents ii AXB-EM232 Enhanced Master RS-232 Controller

Resumen del contenido incluido en la página 5

Product Information Product Information Product Information The AXB-EM232 Enhanced Master RS-232 Controller (FIG. 1) is an AXlink bus device that functions like an AMX Master Card in a single compact enclosure. It is fully compatible with the Axcess Control System and can be used either as a stand-alone device or with other AMX bus devices. The AXB-EM232 runs complete Axcess programs, and controls other AXlink components and two devices using RS-232 as a control protocol. It can also control

Resumen del contenido incluido en la página 6

Product Information Specifications The following table lists the specifications for the AXB-EM232. AXB-EM232 Product Specifications Power 12 VDC, 160 mA Asynchronous data communication • Baud rates: 300, 600, 1200, 2400, 4800, 9600, 19200, or 38400  Data bits: 7 or 8  Stop bits: 1 or 2  Parity: None, Odd, Even, Mark, or Space Memory 64 KB battery protected memory, expandable to 256 KB Front Panel Components: AXlink status LED Green LED lights to indicate AXlink communication as status as

Resumen del contenido incluido en la página 7

Product Information Installation Setting the internal jumpers Some RS-232 devices require that the bus be terminated at 100 ohms. Follow these steps if your device requires this termination. 1. Discharge the static electricity from your body. 2. Unplug the two-pin power connector. 3. Remove the two screws on the front panel. 4. Remove the front panel, and slide the circuit board out of the enclosure. 5. Remove the jumper on pin trio E1 from pins 2-3 and place it on pins 1-2 (FIG. 2). 100 1 E1 2

Resumen del contenido incluido en la página 8

Product Information Refer to the following table when setting the DIP switches. Communication Parameters DIP Switch Settings Switch 1 2 3456 7 8 Function Stop Bits Data Bits Parity Baud Rates Setting Off Off Off Off Off Off Off Off Value 2 bits 7 bits Unused 300 On On On Off Off On Off Off 1 bit 8 bits Unused 600 Off On Off Off On Off Unused 1,200 On On Off On On Off Unused 2,400 Off Off On Off Off On Mark 4,800 On Off On On Off On Even 9,600 Off On On Off On On Odd 19,200 On On On On On On No

Resumen del contenido incluido en la página 9

Product Information Using Ports 1 and 2 for RS-232 data communication 1. Connect the RS-232 wiring to Port 1, as shown in FIG. 4. GND GND RX1 TX Device RX TX1 485EN RS232/422 Port 1 RX1- RX1+ not used TX1- TX1+ FIG. 4 RS-232 Port 1 wiring 2. Connect the RS-232 wiring to Port 2, as shown in FIG. 5. GND GND RX2 TX Device RX TX2 RS232 Port 2 not used CTS2 RTS2 FIG. 5 RS-232 Port 2 wiring 3. Configure the AXB-EM232 for hardware handshaking (request to send, clear to send) by connecting the RS-232

Resumen del contenido incluido en la página 10

Product Information Using Port 1 for RS-422 communication Wire the AXB-EM232 for communicating via RS-422 by connecting the RS-422 wiring to Port 1, as shown in FIG. 7. RS-422 communication is available only through Port 1. GND RX1 TX1 485EN RS232/422 Device TX- Port 1 RX1- TX+ RX1+ RX- TX1- RX+ TX1+ FIG. 7 RS-422 Port 1 wiring Using Port 1 for RS-485 data communication To wire the AXB-EM232 for communicating via RS-485, connect the RS-485 wiring to Port 1, as shown in FIG. 8. RS-485 communic

Resumen del contenido incluido en la página 11

Product Information RS-232 male program connector Use either an AMX RS-232 cable (FG 10-726 ) for a DB-25 connector or AMX Programming cable (FG10-727) for a DB-9 port to connect your PC to the AXB-EM232 and download the Axcess program. Do not use a null modem cable. Program Connector and Pinouts Pin Signal Pin 1 2RXD 3TXD 4 +12 VDC Pin 9 5GND 7 +12 VDC Only an AMX Programming cable or equivalent is to be used due to the voltage on pins 4 and 7. Failure to do so could damage the com port on a

Resumen del contenido incluido en la página 12

Product Information 5. Carefully slide one battery out of its socket, and insert the new battery. 6. Plug the 2-pin power connector in to reapply power. Wait one minute; then, remove the power connector again. 7. Carefully slide the other battery out of its socket, and insert the new battery. 8. Plug in the 2-pin power connector. 9. Slide the circuit board back into the enclosure. 10. Replace the front panel and refasten the two screws. 11. Reconnect any connectors you removed. Mounting the AXB

Resumen del contenido incluido en la página 13

Programming Programming Use the NetLinx Studio software program to create and edit an Axcess Control program for the AXB-EM232: ! The AXB-EM232 occupies address 0. ! Port 1 is AXlink Device 1, and Port 2 is AXlink Device 2. ! To communicate directly with the AXB-EM232, use Terminal Emulation mode. ! To display a list of the commands in the Terminal Emulation mode, type help or ? and press ENTER. ! For online help while in Axcess, press F6. Program the AXB-EM232 as you would the AXC-EM Enhanced

Resumen del contenido incluido en la página 14

Programming Send_Strings This device also has some special Send_String escape sequences. If any of the three-character combinations in the following table are found anywhere within a Send_String program instruction, they will be treated as a command and not the literal characters. Send_String sequences "27,17," Sends a break character of the specified length of time. "27,18,1" Sets the 9 data bit to 1 for all subsequent characters to be transmitted.

Resumen del contenido incluido en la página 15

Programming 11 AXB-EM232 Enhanced Master RS-232 Controller

Resumen del contenido incluido en la página 16

AMX reserves the right to alter specifications without notice at any time. brussels • dallas • los angeles • mexico city • philadelphia • shanghai • singapore • tampa • toronto* • york 3000 research drive, richardson, TX 75082 USA • 469.624.8000 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 © 032-004-1013 10/03 2003 AMX Corporation. All rights reserved. AMX, the AMX logo, the building icon, the home icon, and the light bulb icon are all trademarks of AM