Resumen del contenido incluido en la página 1
RM.406
Professional DJ Mixer
: : :
LR
A B A B AB AB
OWNER’S MANUAL
STANTON MAGNETICS, Inc.
information@stantondj.com
©2004 Stanton Magnetics, Inc.
Resumen del contenido incluido en la página 2
Please read carefully before use of this product Failure to follow the instructions printed below may void warranty • Follow all security advice printed on your mixer • When removing the unit's AC plug from the power source, grasp and pull the plug, NEVER the cord itself! • Avoid placing your mixer near heat sources, such as power amplifiers. • When in use, place your mixer on a stable surface, away from vibration. Always use care when carrying your mixer. Impact, or heavy vibration may compro
Resumen del contenido incluido en la página 3
Welcome Congratulations and thank-you for purchasing the latest addition to the grow- ing Stanton family. Sporting a new attitude, and a fresh, modern look, the RM.406 is a 4-channel, rackmount mixer loaded with features and innova- tions giving club and mobile DJs a complete, powerful, yet simple tool to mix, create, and perform their best. 1/4" and 1/8" headphone outputs, XLR, RCA, and 1/4" Master and Zone outputs, plus plenty of inputs, including three Mic inputs, and a separate 1/8" jack f
Resumen del contenido incluido en la página 4
RM.406 Top Panel (FUNCTIONS) The controls and functions of the RM.406 are grouped in alphabetical sec- tions (clockwise from upper right corner) for your reference and then listed numerically for more detail. G H : : : A B C L R ABA A B BAB D F E Section A: Output Meters Section B: FX Controls Section C: Output Controls Section D: Cue Controls Section E: Crossfader Controls Section F: MP3 / Aux In Section G: Mic Controls Section H: Channel Controls
Resumen del contenido incluido en la página 5
RM.406 Top Panel (FUNCTIONS) Section A: Output Meters 1 2 A 1. Meter Switch: Switches the display of the Level Meter (#2) between Master or Zone output signals. 2. Level Meter: Displays the left and right Master or Zone output level of the mixer. Red indicates clipping. Section B: FX Controls 3 4 5 B 3. Send Level: Controls the output level (send volume) of the FX Loop when a channel’s effects send (#40) is activated. 4. Return Level: Controls the input level (return volume) of the FX Loop when
Resumen del contenido incluido en la página 6
RM.406 Top Panel (FUNCTIONS) Section C: Output Controls 6 7 8 C LR 11 10 9 6. Master Level: Controls the overall output level of the audio signal sent through the Master connectors (see Output Connections.) 7. Stereo/Mono Switch: Switches the Master output between a stereo or mono signal. Mono mode can be used to accommodate some large PA sys- tems. It can also be engaged in the event of a sudden loss of stereo signal in phonograph cartridge connections [Stereo = UP position.] 8. Zone Level:
Resumen del contenido incluido en la página 7
RM.406 Top Panel (FUNCTIONS) Section D: Cue Controls 12 13 14 D 17 16 15 12. Cue FX: Sends the effected signal from the FX Loop to the Headphone Cue for monitoring (see Section-B.) This allows DJs to hear what the FX Loop sounds like, before sending it to the Master Outputs. 13. Split Cue: Controls how the CUE will be heard in the headphones. In the "stereo" position, the pre-selected Cue (#41) will be heard as a stereo signal in the head- phones (full stereo audio signal in both ears.) In "sp
Resumen del contenido incluido en la página 8
RM.406 Top Panel (FUNCTIONS) Section E: Crossfader Controls 18 19 20 21 E 18. Fader Start (A): Activates this side (A) of the Crossfader (#19) for use with com- ponents with the Fader Start feature. Moving the crossfader away from the left-most position will cause the device (CD / Turntable) to start playing. This allows DJs to activate a device by using the fader as if they were pressing Play. [Fader Start com- patible device (CD / Turntable) is required. Fader Start cables need to be conn
Resumen del contenido incluido en la página 9
RM.406 Top Panel (FUNCTIONS) Section F: MP3/Aux In 22 F 22. MP3 / Aux. Input: This 1/8" Mini-jack (3.5 mm) input was designed for easy access and connectivity to a variety of portable devices (portable MP3 / mini-disc / CD players / iPods.) Use this input instead of having to re-wire the back panel of the mixer or use adapters. Section G: Mic Controls G 23 24 25 26 27 28 29 30 31 32 33
Resumen del contenido incluido en la página 10
Section G: Mic Controls (continued) 23. Mic-1 XLR Input: Primary connection for a standard balanced (XLR) microphone. 24. Mic-2 XLR Input: Secondary connection for a standard balanced (XLR) microphone. 25. Mic-1 1/4" Input: Primary connection for a standard unbalanced (1/4") microphone. 26. Mic-2 1/4" Input: Secondary connection for a standard unbalanced (1/4") microphone. 27. Mic-1 Level: Controls the output level (volume) of Microphone 1 only. 28. Mic-2 Level: Controls the output level (volume
Resumen del contenido incluido en la página 11
RM.406 Top Panel (FUNCTIONS) Section H: Channel Controls (each channel has its own controls which are duplicated for channels 1-4) H 34 35 36 37 38 39 41 40 42 AB 43 34. Input selector switch: Selects phono or line input for the corresponding channel. This is a three way switch allowing input from only one device at a time (Phono or either of two Line level inputs (for connections in rear panel of mixer, see Sections N-R.) 35. Channel EQ (HIGH): Controls High frequency equalization of correspon-
Resumen del contenido incluido en la página 12
RM.406 Top Panel (FUNCTIONS) Section H: Channel Controls (continued) this setting too high may result in a loss of sound quality (distortion.) [Note: For best results set this control in the number 7 (2 O'Clock) position for unity gain. If further adjustment is needed, this is a good reference point.] 37. Channel EQ (MID): Controls Mid frequency equalization of correspon- ding channel (+9/-64 dB.) [Note: -64dB = complete KILL of frequency. Any changes made to EQ settings will affect the ov
Resumen del contenido incluido en la página 13
RM.406 Rear Panel (FUNCTIONS) K L I J M N O P Q R Section I: Power Section J: Master Output Section K: FX (Send & Return) Section L: Zone Output Section M: Sub Output Section N: RCA Outputs Section O: Channel 4 Inputs Section P: Channel 3 Inputs Section Q: Channel 2 Inputs Section R: Channel 1 Inputs Section I: Power I. Power Switch & Connection: This is the ON / OFF power switch for the entire mixer. Only use the supplied adaptor (18v AC 1A) or one authorized by a Stanton dealer or our servi
Resumen del contenido incluido en la página 14
RM.406 Rear Panel (FUNCTIONS) Section J: Master Output J. Master Output Connection: These Right & Left XLR connections are used for the Master Output signal. Volume levels for this output are controlled by the section C front panel controls. NOTE: The TRIM knob sets the maxi- mum volume allowed for this output (be sure it is set properly.) It should be used in conjunction with the Master Fader (#6) as well as individual Gain (#36) and Channel Faders (#42) when establishing optimal overall outp
Resumen del contenido incluido en la página 15
RM.406 Rear Panel (FUNCTIONS) Section P: Channel 3 Inputs P. Channel 3 Input Connections: This group of connections are ALL inputs which are only routed to channel 3 (select input using section H, (#34) from top panel.) Only two lines (L3, L7) and one phono (PH3) OR CD can be used as inputs here (the select switch located here toggles between PH3 / CD.) The 1/8” connection is used only for connecting devices with the Fader Start feature with the appropriate cables (to activate Fader Start for
Resumen del contenido incluido en la página 16
Application Example This is a typical setup you’ll find in many nightclubs: 2 turntables, 2 CD play- ers, plus a microphone for the DJ. Here’s how you would set up your equip- ment with the RM.406: 1. Be sure all equipment is powered “OFF” and all of theRM.406’s Channel faders and Level knobs are at minimum volume. 2. Connect the turntables to the Phono inputs of Channels 1 and 4. Be sure the rear-panel toggle switch for Channel 4 is set to “PH2” or you won’t hear anything. To avoid hum, don’t
Resumen del contenido incluido en la página 17
Superior Sound Technology The audio quality of the RM.406 is nothing short of revolutionary for DJ mix- ers in its price class. The RM.406 was designed by Stanton’s new product development team, seasoned audio professionals who have designed world class professional recording studio and broadcast mixers and product man- agers who are working DJs and work closely with some of the world’s most respected DJs. They have taken their knowledge and experience to create the RM.406, a DJ mixer with super
Resumen del contenido incluido en la página 18
Technical Specifications Line Inputs.................................................................................7 x 2 (RCA) , -10 dBV / >10 kOhm 1 (1/8” stereo mini-jack), 10 dBV / >10kOhm Phono / CD Inputs...................................2 x 2 (RCA), -46 dBV / -10 dBV / 47 kOhm / >10 kOhm Phono..............................................................................1 x 2 (RCA), -46 dBV (Phono) / 47 kOhm Phono / Mic Input..................................1 x 2 (RCA), -46 dBV (Phono)
Resumen del contenido incluido en la página 19
Troubleshooting Problem / Symptom Possible Cause/ Solution Is the power on? Check the power switch. Make sure the channels are assigned properly to the crossfaders. Make sure INPUT GAIN is turned up No Sound and output level control is turned up. Depending on the input, check the rear panel selector switches. Check the top panel channel selector switches. No Sound- Master Output (Booth and Make sure that MASTER TRIM on the rear Zone are OK) panel is turned up. Do the headphones work with the C
Resumen del contenido incluido en la página 20
Troubleshooting Problem / Symptom Possible Cause/ Solution Only plug turntables into this input, do not plug in CD Sound is distorted players or other Line Level sources. Turn down the Phono Input INPUT GAIN CONTROL. Check the EQ settings. Make sure you are using good shielded audio cables. Some less expensive audio cables can be susceptible to hum and interference. Keep your audio cables away from AC power cables and AC transformers. Make sure I hear hum. the mixer is not mounted too close to
