Nuestro propósito es proporcionarte el acceso más rápido posible a los contenidos incluidos en los manuales de instrucciones del aparato Vax RS 232C. Utilizando la vista previa online, puedes ver rápidamente el índice de contenidos y pasar a la página donde encontrarás la solución a tu problema con Vax RS 232C.
Para tu comodidad
Si ver los manuales de instrucción de Vax RS 232C directamente en esta página no es cómodo para ti, puedes utilizar dos soluciones posibles:
Vista en pantalla completa – Para ver cómodamente los manuales de instrucciones (sin descargarlos en tu ordenador) puedes utilizar el modo de vista en pantalla completa. Para activar la vista del manual Vax RS 232C en pantalla completa, utiliza el botón Pantalla completa
Descargar al ordenador – también puedes descargar el manual de instrucciones de Vax RS 232C a tu ordenador y guardarlo en tu colección. Sin embargo, si no quieres ocupar espacio en tu dispositivo, siempre podrás descargarlo de ManualsBase.
Muchas personas prefieren no leer el documento en la pantalla, sino en versión impresa. La opción de impresión también está prevista y puedes utilizarla haciendo clic en el enlace más arriba - Imprimir el manual. No tienes que imprimir el manual completo de Vax RS 232C, solo las páginas que elijas. Ahorra papel.
Resúmenes
A continuación encontrarás resúmenes de los contenidos incluidos en las páginas posteriores del manual de instrucciones para Vax RS 232C. Puedes utilizarlos si quieres ver rápidamente el contenido que se encuentra en la siguientes páginas del manual.
Resúmenes de contenidos
Resumen del contenido incluido en la página 1
9000 Series Mixer/Amplifiers RS-232C Protocol Manual Ver.3.11 2006/11/14 Page 1 of 24
Resumen del contenido incluido en la página 2
TABLE OF CONTENTS Page# 1. SUMMARY…………………………………………………………………….... 3 2. SERIAL PORT SETTING…………………………………………………….... 3 3. COMMAND CONFIGURATION………………………………………………. 4 4. TRANSMISSION DATA AFTER COMMAND RECEPTION……………….. 4 5. CONTROL COMMAND AND SETTING VALUE……………………………. 5 5.1. Channel Fader Gain……………………………………………………………. 5 5.1.1. Channel Fader Gain - Position setting…………………………………… 5 5.1.2 Channel Fader Gain - Step Up/ Step Down…………………………….…. 7 5.2. Crosspoint Gain…………………………………………………
Resumen del contenido incluido en la página 3
1. SUMMARY The RS-232C protocol described in this document is designed to be used to control the 9000 Series Amplifier from a PC and/or remote controller. This specification applies to the 9000 Series firmware version 3.10 or later. Settings that can be controlled are as follows: Channel fader gain Crosspoint gain (Mixer mode only) Preset memory recall Channel ON/OFF Power ON/OFF Tone control (Bass/Treble) EQ settings (ON/OFF, Band number selection, Gain setting, Q
Resumen del contenido incluido en la página 4
3. COMMAND CONFIGURATION Data length (N) Data 1 Data 2 Data N Command is in the range of 80H to FFH. and are in the Command Data length range of 00H to 7FH. Data Data length (N) refers to the length of the subsequent data of Data 1 to Data N. If received data contains more byte data than the Data length, these exceeding data are abandoned. If a next
Resumen del contenido incluido en la página 5
5.1. Channel Fader Gain 5.1.1. Channel Fader Gain - Position setting Set the input and output channel fader gains to a fixed value position. Note: Command cannot be received during power off. 9000Series Amplifier responds with the same data as that received. 91H, 03H, , , 00H: Input channel 01H: Output channel 00H - 07H (Input channel 1 - 8) 00H - 07H (Output channel 1 - 8) Pos
Resumen del contenido incluido en la página 6
Position Gain Position Gain Position Gain Position Gain HEX DEC (dB) HEX DEC (dB) HEX DEC (dB) HEX DEC (dB) 00H 0 - ∞ 22H 34 -36.0 44H 68 -19.0 66H 102 -2.0 01H 1 -70.0 23H 35 -35.5 45H 69 -18.5 67H 103 -1.5 02H 2 -68.0 24H 36 -35.0 46H 70 -18.0 68H 104 -1.0 03H 3 -66.0 25H 37 -34.5 47H 71 -17.5 69H 105 -0.5 04H 4 -64.0 26H 38 -34.0 48H 72 -17.0 6AH 106 0.0 05H 5 -62.0 27H 39 -33.5 49H 73 -16.5 6BH 107 +0.5 06H 6 -60.0 28H 40 -33.0 4AH 74 -16.0 6CH 108 +1.0 07H 7 -59.0 29H 41 -32.5 4B
Resumen del contenido incluido en la página 7
5.1.2 Channel Fader Gain - Step Up/ Step Down Set the input and output channel gain positions by the number of steps. Positions can be varied from the current status by the designated number of steps. One position varies per step. 9000Series Amplifier responds with the same data as that received. The 9000series Amplifier informs position values changed by Step Up or Down. 93H, 03H, , , 00H: Input channel 01H: Output cha
5.2. Crosspoint Gain Set the crosspoint switch gain. 9000Series Amplifier responds with the same data as that received. This command is enabled when in the mixer mode only. Note: Command cannot be received during power off. 95H, 05H, , , , , 00H: Input channel 00H - 07H (Input channel 1 - 8)
Resumen del contenido incluido en la página 10
CROSSPOINT GAIN TABLE value Gain Value Value Value Gain (dB) Gain (dB) Step Down (dB) HEX DEC HEX DEC HEX DEC HEX DEC 00H 0 - ∞ 22H 34 -37.0 44H 68 -3.0 65H 101 -6.0 step 01H 1 -70.0 23H 35 -36.0 45H 69 -2.0 66H 102 -7.0 step 02H 2 -69.0 24H 36 -35.0 46H 70 -1.0 67H 103 -8.0 step 03H 3 -68.0 25H 37 -34.0 47H 71 0.0 68H 104 -9.0 step 04H 4 -67.0 26H 38 -33.0 48H 72 1.0 69H 105 -10.0 step 05H 5 -66.0 27H 39 -32.0 49H 73 2.0 6AH 106 -11.0 step 06H 6 -65.0 28H 40 -31.0
Resumen del contenido incluido en la página 11
5.3. Preset Memory Recall Recalls any desired preset memories. 9000Series Amplifier responds with the same data as that received. Note: Settings to be stored in preset memories are referred to as “SCENE” in mixer mode and “EVENT” in matrix mode. In 'Matrix mode', the command of 'EVENT end' is not provided. Therefore, it is recommended to use ‘Preset memory recall’ command only for Mixer mode ‘SCENE’ activation. In the case of using this command for ‘EVENT’ activation in Matrix
Resumen del contenido incluido en la página 12
5.4. Channel ON/OFF This performs ON/OFF setting of the Input or Output channel. 9000Series Amplifier responds with the same data as that received. 92H, 03H, , , 00H: Input channel 01H: Output channel 00H - 07H (Input channel 1 - 8) 00H - 07H (Output channel 1 - 8) 00H: Channel OFF 01H: Channel ON Example 1: Setting the Input Channel 1 to ON 92H, 03H, 00H, 00H, 01H Ex
Resumen del contenido incluido en la página 13
5.6. Tone Control Performs Bass and Treble gain settings of the input/output channels. 9000Series Amplifier responds with the same data as that received.. Note: Command cannot be received during power off. AAH, 04H, , , , 00H: Input channel 01H: Output channel 00H - 07H (Input channel 1 - 8) 00H - 07H (Output channel 1 - 8) 00H: Bass Gain 01H: Treble Ga
Resumen del contenido incluido en la página 14
TONE CONTROL GAIN POSITION TABLE Value Gain (dB) Value Gain (dB) HEX DEC HEX DEC 00H 0 -12.0 0DH 13 +1.0 01H 1 -11.0 0EH 14 +2.0 02H 2 -10.0 0FH 15 +3.0 03H 3 -9.0 10H 16 +4.0 04H 4 -8.0 11H 17 +5.0 05H 5 -7.0 12H 18 +6.0 06H 6 -6.0 13H 19 +7.0 07H 7 -5.0 14H 20 +8.0 08H 8 -4.0 15H 21 +9.0 09H 9 -3.0 16H 22 +10.0 0AH 10 -2.0 17H 23 +11.0 0BH 11 -1.0 18H 24 +12.0 0CH 12 0 Value Step Down Value Step Up HEX DEC HEX DEC 21H 33 -1.0 step 2DH 45 +1.0 step 22H 34 -2.0 step 2EH 46
Resumen del contenido incluido en la página 15
5.7. EQ Settings Perform EQ settings (ON/OFF, Band number, Gain, Q and Center frequency) of the input/output channels. 9000Series Amplifier responds with the same data as that received. Band number, Gain, Q, and Center frequency cannot be received when EQ is set to OFF. They can be valid only when EQ is set to ON. Note: Command cannot be received during power off. A1H, 07H, , , , , , ,
5.8. Loudness Compensation Settings Perform loudness compensation settings of the Input / Output channels. 9000Series Amplifier responds with the same data as that received. Note: Command cannot be received during power off. ABH, 03H, , , 00H: Input channel 01H: Output channel 00H - 07H (Input channel 1 - 8) 00H - 07H (Output channel 1 - 8) 00H: Loudness OFF 01H: Loudnes
Resumen del contenido incluido en la página 18
5.9. Filter Settings Perform Filter (HPF/LPF) settings of Input / Output channels. 9000Series Amplifier responds with the same data as that received. Note: Command cannot be received during power off. A2H, 04H, , , , 00H: Input channel 01H: Output channel 00H - 07H (Input channel 1 - 8) 00H - 07H (Output channel 1 - 8) 00H: High Pass Filter 01H: Low Pass Filter
Resumen del contenido incluido en la página 19
5.10. Input Sensitivity Setting Performs input sensitivity setting of Input channel. 9000Series Amplifier responds with the same data as that received. Input sensitivity setting is enabled only for the channel on which the D-001T or AN-001T is used. Note: Command cannot be received during power off. ACH, 02H, , 00H - 07H (Input channel 1 - 8) INPUT SENSITIVITY TABLE Value Sense Value Sense (dB) (dB) HEX DEC HEX DEC 00
Resumen del contenido incluido en la página 20
6. Channel Name Request Reads input and output channels’ names. The 9000 Series Amplifier responds with the channel name to this command. F0H, 03H, 40H, , 00H: Input channel 01H: Output channel 00H - 07H (Input channel 1 - 8) 00H - 07H (Output channel 1 - 8) Example: Acquiring the Input Channel 1’s name. F0H, 03H, 40H, 00H, 00H Response data are provided below. C0H, 09H, , <
