Resumen del contenido incluido en la página 1
SPARE PART AND OPERATION MANUAL
FOOD MIXER
Model W20D
Resumen del contenido incluido en la página 2
Caution -READ BEFORE OPERATING- Caution Varimixer recommends that mixer operators be at least 18 years of age and be thoroughly trained on the use of the mixer. Varimixer recommends that the following precautions be adopted to help make the mixer operation safer and more efficient. ........- All operators should be at least 18 years of age. - All operators should be thoroughly trained before being allowed to operate the mixer. - NEVER reach into the bowl when the mixer is running. - Do not
Resumen del contenido incluido en la página 3
LIMITED WARRANTY Varimixer warrants its commercial mixers to the original purchaser against defects in material or manufacture for a period of one year from the date of original purchase, subject to the following exclusions and limitations. The warranties provided by Varimixer do not apply in the following instances: EXCLUSIONS 1. In the event that the equipment is improperly installed. Proper installation is the responsibility of the installer, proper installation procedures are covered in the
Resumen del contenido incluido en la página 4
TABLE OF CONTENTS Installation Instructions...................................................................................................2 Cleaning Instructions.....................................................................................................2 Operating Instructions....................................................................................................3 Front Panel Controls.....................................................................................
Resumen del contenido incluido en la página 5
Read this page entirely BEFORE beginning installation. VARIMIXER INSTALLATION INSTRUCTIONS The mixer must be mounted with the rubber feet, which neutralize both shaking and rusting. If the unit is to be installed on top of a table, the unit must be bolted down with the two bolts supplied from the shipping pallet. Before the mixer is connected to power, it should be checked that the voltage and frequency on the rating plate is correct in relation to the place of installation. The rating plate is
Resumen del contenido incluido en la página 6
Operation of the Mixer. Power Up and Default: 1. Turn power on Mixer. (Plug in 115AC) - 1:00 Appears on the display. - The slow speed LED lights. (Left LED) 2. Press the bar arrow between the slow and fast LEDs. - 2:00 Appears on the display. - The fast speed LED lights. (Right LED) 3. Press the bar arrows between the slow and fast LEDs. Note: These are the factory default times for slow and fast speed. The computer will go to factory or stored times on every power up. Setting The Slow Speed Tim
Resumen del contenido incluido en la página 7
Operation of the Mixer. Change Time in Fixed mode: 1. Press and hold the bar arrow key for 5 sec. and release. 2. The fixed time for the slow speed will appear in the display. - The LED for slow speed lights. (Left LED) 3. Press the time up keys under the display to enter the desired time for slow speed. 4. Press the bar arrow key. 5. The fixed time for the fast speed will appear in the display. - The LED for fast speed lights.(Right LED) 6. Press the time up keys under the display to enter the
Resumen del contenido incluido en la página 8
Body 1 2 3 4 5 6 7 8 9 10 14 13 15 12 11 16 17 18 19 20 21 5
Resumen del contenido incluido en la página 9
Body Figure Number Description Part Number 1. Screw STA 5233 2. Top Lid (Painted) 20D-21 3. Rear Access Plate 20N-291 4. Bushing (Lift Handle) STA 2515 5. Upper Column 20N-22.17 6. Plug Button STA 6561 7. Bushings STA 2514 (each) 8. Column Seal 20N-207 9. Plug Button STA 6511 10. Lower Column 20N-22.30 11. Bolt M8X20 STA 5631 12. Leg Left 20N-25.1 13. Leg Right 20N-25.2 14. Plug Button STA 6560 15. Rubber Foot 20N-218 16. NSF Cover Plate 20N-304 17. Suspension Hook 20N-302 18. Column Base Plate
Resumen del contenido incluido en la página 10
Bowl Arms 1 7 6 2 3 4 10 5 11 8 9 12 13 15 14 16 19 17 18 20N-65.1Z 20N-62Z 20N-65.1M 7
Resumen del contenido incluido en la página 11
Bowl Arms Figure Number Description Part Number 1. Ball (Black) STA 3306 2. Bowl Lift Lever 20N-62Z 3. Washer STA 6066 4. Disc With Arrow 20N47.10 5. Retaining Disc 20N-47.11 6. Crank Arm 20N-63M 7. Cotter Pin STA 6204 8. Key STA 2019 9. Snap Ring STA 3407 10. Lift Nut 20N-65.1Z 11. Jam Nut STA 5825 12. Lift Bolt 20N-83.1 13. Bowl Arm Shaft 20N-68.1M 14. Snap Ring 25U STA 3410 15. Bowl Arm 20N-23 16. Snap Ring 25U STA 3410 17. Bowl Lift Lever Assembly 20N-62Z 18. Lift Bolt Assembly 20N-65.1M 19.
Resumen del contenido incluido en la página 12
Pulley System 4 5 6 7 1 3 2 8 9
Resumen del contenido incluido en la página 13
Pulley System Figure Number Description Part Number 1. Belt 20P-91 2. Motor Pulley 6J19 3. Planetary Pulley 6J60 4. Bolt 3/8-16X3/4 Local Purchase Item 5. Washer STA 6009 6. Bolt M6X16 STA 5432 7. Washer STA 6008 8. Motor 20D-85.64 10
Resumen del contenido incluido en la página 14
Planetary Head 1 2 3 4 5 6 7 8 12 13 9 14 15 10 16 20 17 11 21 18 22 19 23 24 25 27 28 26 29 30 31 32 33 20N-2.1Z 20N-2.1Z 20N-3 20N-2 34 35 20-36 20N-30 20-33 20N-101 11
Resumen del contenido incluido en la página 15
Planetary Head Figure Number Description Part Number 1. Snap Ring STA 3414 2. Bearing 6206 20-98 3. Snap Ring STA 3518 4. Bolt M6X16 STA 5432 5. Main Bearing Head 20N-3 6. Snap Ring STA 3518 7. Bearing 6206 20-98 8. Distance Piece 20-37 9. Gear Wheel Rim 20N-1 10. Bolt M8X30 STA 5626 11. Main Shaft 20N-30 12. Snap Ring STA 3470 13. Eccentric Disc 20-36 14. Bearing 6006 20-100 15. Snap Ring STA 3515 16. Snap Ring STA 3414 17. Seal 20N-108R 18. Needle Bearing Race See item 25 19. Groove Pin STA 6
Resumen del contenido incluido en la página 16
Attachment Drive 1 2 3 4 5 6 7 8 9 11 10 12 13 14 15 1 1/2” 2” I.D. I.D. 20N-10.6M 20N-10.5M 20N-10.6M #17 Hub #12 Hub 13
Resumen del contenido incluido en la página 17
Attachment Drive Figure Number Description Part Number 1. Snap Ring STA 3410 2. Wormwheel 20N-9 3. Snap Ring STA 3512 4. Bearing 15-105 5. Distance Piece 20N-37 6. Bearing 15-105 7. Key STA 2031 8. Shaft F/ #17 Hub 20N-50 8A. Shaft F/ #12 Hub 20J-50 9. O-ring STA 3127 10. Hub F/ #17 (2” I.D.) 20N-8 10A. Hub F/ #12 (1 1/2” I.D.) 20J-8 11. Thumb Screw F/ #17 STA 5561 11A. Thumb Screw F/ #12 4R-125 12. Gasket 20N-211 13. Lock Washer STA 6038 14. Bolt STA 5631 15. Cover F/ #17 15-214 15A. Cover F/
Resumen del contenido incluido en la página 18
Computer Display Control 2 6 1 3 4 7 5 15
Resumen del contenido incluido en la página 19
Computer Display Control Figure Number Description Part Number 1. Control Panel Assembly 20E-605M with start/stop buttons and computer display. 2. Start Button Assembly 31-174.2 3. Stop Button Assembly 31-174.3 4. Screw STA 5230 5. Interface Board Assembly 20E-606 6. Front Plate Casting 20N-650.5 7. Ribbon Cable 8073882 8. Cube Relay 8070834 16
Resumen del contenido incluido en la página 20
Bowl Screen 2 3 4 10 5 8 6 11 9 7 12 13 1 14 15 16 18 17 17
